Intratone Intracall 14-0144 User Manual

INSTALLING AND CONNECTING THE

INTRATONE INTRACALL INTERCOM

GENERAL POINTS

The INTRACALL (14-0144) audio intercom is ideal for professional and private use. It
connects to an Intratone Telecom module for optimised installation and management.

This guide describes the connection and set-up procedure for the INTRATONE
INTRACALL intercom.

The Intratone INTRACALL intercom

Operating warranty:

The intercom is guaranteed within a temperature range of -20°C to +70°C and a level of
relative humidity not exceeding 70%.

End-of-life recycling of the product:

The intercom and its accessories must not be disposed of with unsorted
municipal waste, but must follow the WEEE (Waste Electrical and Electronic
Equipment) collection and recycling channel).

V233 – 5024 – AA Page 1 / 9

TABLE OF CONTENTS

GENERAL POINTS ----------------------------------------- 1
TABLE OF CONTENTS ----------------------------------- 2
DIMENSIONS ------------------------------------------------- 3

A) DIMENSIONS OF THE BUILT-IN WALL BOX AND SURFACE-MOUNTED BOX -------- 3
B) INTERCOM DIMENSIONS --------------------------------------------------------------- 4

WIRING -------------------------------------------------------- 5

A) WIRING WITH A 3G UNIT AND A RELAY BOARD (12-0110) ------------------------ 5
B) WIRING WITH A TWO-DOOR CENTRAL UNIT (03-0101) ---------------------------- 6

EQUIPMENT CONFIGURATION ------------------------ 7

A) EQUIPMENT PROGRAMMING ---------------------------------------------------------- 7
B) INTERCOM SETTINGS ------------------------------------------------------------------ 8

POST-INSTALLATION CHECK ------------------------- 8
TROUBLESHOOTING ------------------------------------- 8
CERTIFICATE OF CONFORMITY ---------------------- 9

V233 – 5024 – AA Page 2 / 9

DIMENSIONS

Top

Botto

Surface-

mounted box

(optional)

Top

Botto

Built-in wall

box

(included)

A) DIMENSIONS OF THE BUILT-IN WALL BOX AND SURFACE-MOUNTED BOX

V233 – 5024 – AA Page 3 / 9

B) INTERCOM DIMENSIONS

V233 – 5024 – AA Page 4 / 9

WIRING

Power supply
12-24 DC 2A

3G

Module

Optional

assembly for

door opening

Exit push button and

door contact input

Wiring info:

-Twisted cable, 0.8 mm
diameter

-100 metres max.

03-0102 CIC12

A) WIRING WITH A 3G UNIT AND A CIC12 CENTRAL UNIT (03-0102)

Up to three 12-0110 relay cards maximum can be added to this central unit to allow four
doors to be opened together or separately.

V233 – 5024 – AA Page 5 / 9

B) WIRING WITH A TWO-DOOR CENTRAL UNIT (03-0101)

Power supply
12-24 DC 2A

Module

3G

Pushbutton, mail

alert and door

contact input

03-0101

See central unit
guide

Wiring info:

-Twisted cable, 0.8mm diameter

-100 metres max. between each
system component

Intercom wiring to connectors 3 and 4 is the same when an extension board is used

(12-0109).

V233 – 5024 – AA Page 6 / 9

Configurer

Configurer

EQUIPMENT CONFIGURATION

Create

Create

A) EQUIPMENT PROGRAMMING

The call number programming procedure for this intercom is configured online on

www.intratone.com

After logging into your account and creating your apartment building, just declare your
Intracall intercom using the “Create” button and follow the instructions on screen.

After naming it, and depending on your configuration, you will be asked for the serial
number of the central unit and the GSM unit contract reference.

CENTRAL UNIT: hardware match

To configure the call numbers, click on your access point to the apartment block and then
click on the “Configure” button.

Define caretaker call(s)

You can then define up to 8 different numbers for each 24-hour period using the time slots
configurable online.

Call programming example:

 NB: For 3G audio subscriptions, the number of programmed numbers must not

exceed the number of records stated in your subscription.

V233 – 5024 – AA Page 7 / 9

B) INTERCOM SETTINGS

Failure

Reason

Resolution

Audio interference

Poor 3G unit reception

Move unit, install an antenna

Call button ineffective

No call number recorded

Check programming

No back-lighting on name
holders

Check power supply at
intercom terminals

Resident can hardly hear
visitors during calls

Microphone obstructed

Clean the microphone port

The intercom calls the
telephone correctly but no
sound or voice synthesis
heard

Incorrect wiring on the A+
and/or A- terminal blocks

Check audio bus wiring

Use the “Configure me” item in the “Central units” menu to adjust different settings. For

instance: volume, number of ring tones, etc.

POST-INSTALLATION CHECK

- Checking audio call quality during a call.

- Check that the resident is able to open the door by pressing the * key on the
telephone (default) while calling.

TROUBLESHOOTING

 Contact our technical services ([phone]) 

V233 – 5024 – AA Page 8 / 9

CERTIFICATE OF CONFORMITY

V233 – 5024 – AA Page 9 / 9