Contents
ⅠⅠ
Installation Manual
1. Hardware Installation
2. Software Installation
ⅡⅡ
User Manual
3. User Manual- Server
01. Main Program
02. Search Program
03. AVI Backup Manager
04. Backup Manager
4. User Manual- Client
01. NetClient Program
02. WebClient Program
※※
Annex
Annex 1. I/O Device
Annex 2. Dynamic IP
Annex 3. IP Router
Ⅰ
Installation manual - Hardware Installation
11.. HHaarrddwwaarree IInnssttaallllaattiioonn
Please check contents before installation: DVR Board, Extension
Cable, Audio & PTZ Installation, etc., if you are missing any parts
please contact your local dealer.
1. DVR Board & Extension Cable Installation
1-1. Insert the DVR Board to an empty PCI Slot in DVR PC.
<DVR Board>
<Mainboard>
1-2. Use Extension Cable to connect cameras.
<Extension Cable-1>
2. DVR Audio Installation
2-1. Prepare DVR PC and MIC.
2-2. Connect the MIC to the Mainboard MIC Port of DVR PC OR
the Audio IN port on DVR Board. Please connect the Speaker to
the back panel of DVR PC.
<DVR System Back Panel>
<MIC>
<Speaker>
Either connect the MIC to Audio IN port of DVR Board OR Mainboard MIC port.
- H Board: Connect the 4CH MIC(B) to DVR Board(A) starting
from the left.
<4CH>
<DVR Board>
<DVR Board>
<Extension Cable-2>
<H DVR Board>
4
5
Ⅰ
Installation manual - Hardware Installation
- HP Board: Connect the 8CH MIC(B) to DVR Board(A) starting
from the top.
<8CH>
<HP DVR Board>
- RC Board: Connect the 4CH MIC(B) to DVR Board(A) starting
from the left.
<4CH>
3. P/T/Z Installation
3-1. P/T/Z Cable
[A] Cable : Connect to COM port of DVR PC
[B] Cable : Connect to DVR Board
[C] Cable : Connect to Receiver Cable
<DVR System>
B
A
<DVR Board>
C
<P/T/Z Cable>
4. Real Display(RD) Board Installation
4-1.
Insert the Real Display Board into an empty PCI Slot in DVR PC.
4-2. Use Cable to connect Real Display Board with DVR Board.
A
<RD Board>
<Mainboard>
<DVR Board>
Real Display Board cannot be used alone, it must be used with S, H, HPLUS
6
<RC DVR Board>
DVR Boards.
B
7
Ⅰ
Installation manual - Software Installation
5. I/O Board Installation
5-1. Prepare Sensor, Alarm, I/O Board and I/O Extension Board for I/O
Board Installation.
< 8 port In/Out Connection>
4CH Input
5CH Output
I/O Extension Board
4CH Input
3CH Output
A : Industrial Case System can use In/Out port separately when additional
Back Panel is available.
A
<I/O Board>
< 16 port In/Out Connection>
To use 16 port In/Out,
A : Slave Board must remove jumper.
B : Master Board must install jumper.
<DVR Board>
A
1. Software Installation
You can install SmartDVR Software by using SmartDVR Formula CD
or downloading from INTOTECH website, www.intotech.co.kr.
Software CD consists of Server Package (Main program, WebClient
program, Apache HTTP Server program), Client Package (NetClient
program) & AVI Codec. User Manual is also available from SW CD.
[Main Program Installation]
Insert SmartDVR Formula CD into CD-ROM drive or run
DvrSetup.exe file; the following installation screen will appear .
Click the icon below and Main Program installation will
automatically proceed.
<I/O Slave Board>
B
8
<I/O Master Board>
WebClient -> SmartDVR Formula
9
Installation Step : Apache HTTP Server (Web Server) ->
Ⅰ
Installation manual - Software Installation
1. SmartDVR Apache HTTP Server (Web Server) Installation
1-1 Installation wizard tool will appear. Click [Next].
1-2 Read the License Agreement and if you agree to the
contents, select [I accept…] and click [Next].
1-3 Click [Next] after checking server information of Apache
HTTP Server.
1-4 Insert Network Domain, Server Name, Administrator’s
E-mail Address.
(This procedure is only a formality. In general cases, follow example)
Select [Run as a service for All Users – Recommended]
and click [Next].
10
11
Ⅰ
Installation manual - Software Installation
1-5 Select Setup Type as [Complete] and click [Next].
1-6 Click [Next] without change of setting. Note: Do not change
the directory!
1-7 After the setting is finished, click [Install] and start installation.
1-8 After the installation is done, click [Finish].
12
13
Ⅰ
Installation manual - Software Installation
1-9 After the installation is finished, a message confirming the
change of the Server port of Apache will appear.
2 SmartDVR WebClient Installation
2-1 After the Installation Wizard Tool is appeared, click [Next].
2-2 Check the contents of License Agreement; if you agree to the
contents, click [Yes].
2-3 After the installation is done, click [Finish].
14
15
Ⅰ
Installation manual - Software Installation
3 SmartDVR Formula Installation
3-1 After Installation Wizard Tool is appeared, Click [Next].
3-2 Check the details of License Agreement; if you agree to the
contents, click [Yes].
3-3 After choosing [Destination Folder] for installation, click
[Next].
3-4 After the installation is done, click [Finish].
16
17
Ⅰ
Installation manual - Software Installation
3-5 Driver Installation: Wizard automatically installs drivers
according to each board type.
3-6 Reboot PC after all the installation.
4. SmartDVR Formula Uninstallation
4-1 Goto [Start] – [Control panel] and click [Add/Remove
Program].
4-2 Select [SmartDVR Formula] and click [Change/Remove].
5 NetClient Installation
5-1 After the Installation Wizard Tool is appeared, click [Next].
5-2 After choosing [Destination Folder] for installation, click [Next].
18
Click the icon below and NetClient Program installation will proceed.
19
Loading...