Intex MegaMixer AMX110, MegaMixer AMX620, MegaMixer AMX622 Operating/safety Instructions Manual
FU L LY GUARANTEED
OPERATING & SAFETY
INSTRUCTIONS
AMX110 AMX620 AMX622
intex.com.au • portamix.co.nz
BUILDING E XCE LLENCE
BUILDING E XCE LLENCE
TECHNICAL DATA
TECHNICAL DATA AMX110 AMX620 AMX622
Power Input 1050 W 1600W 1600W
Voltage 230V/50Hz 230V/50Hz 230V/50Hz
Number of Gears 1 2 2
No-Load-Speed 0 - 550
Protection/ Class of Protection
Certification CE, GS CE, GS CE, GS
Thread for fixing the Tool M14X2 M14X2 QR H13
Mixing Paddle (φ max.) 120mm 140mm
Double
Insulation/¨
180-460/300700min-1
Double
Insulation/¨
100-420/15060 0min-1
Double
Insulation/¨
2 x 120mm special
set or 1 x 140mm
QR H13
SAFETY INSTRUCTIONS
Safe operation of this machine is possible only when the operation instructions, and the safety
precautions are read completely and the instructions contained therein are strictly observed.
• Never use the machine in an explosive or inflammable atmosphere where
danger of explosion exits.
• Serious injury can occur through misuse or accident. Do not work in a cluttered or unsafe
working area. Keep children away from mixing equipment.
• The machine must not be damp and must not be operated in a wet environment.
• Always wear eye, respiratory and hearing protection equipment and suitable protective clothing.
• Always inspect cable and plug before using machine. All repairs must be carried out by a
qualified professional.
• Machines that are used with wet materials or in damp areas should be used with a residual
current circuit breaker. Use only extension cables that are intended for outdoor use and are
protected against splash water.
• Ensure the machine is turned off before connecting to the power socket.
• Keep the power cable away from the machine mixing helix.
• Ensure long hair, loose clothing and fashion accessories are well tied back away
from the mixing shafts.
• When working with the machine, always hold it firmly with both hands and ensure a firm stable
working position. Secure the vessel with the mixed substance against moving on the floor.
• Do not carry the machine by the power cord.
• Disconnect the machine from the power source before attaching or removing the mixing
helix or attempting any repairs to the machine.
STARTING OPERATION & USE
Check if the data on the nameplate is corresponding with the actual mains voltage.
IMPROPER USE MAY DAMAGE THE POWER TOOL OR CAUSE INJURY:
• Only use mixing paddles up to the specified diameter.
• The variable speed feature is designed to allow gentle start up and shut down to avoid splashing
and wastage. To avoid the motor overheating or burning out, use the machine on full power
when mixing under load.
CONNECTING THE M14 THREADED MIXING-PADDLE:
Thread the mixing-paddle clock-wise into the mixer spindle until the hex nut on the mixer shaft is in
contact with the spindle. Do not operate the machine unless the mixing helix is correctly fitted.
CONNECTING THE DOUBLE COUNTER- ROTATING MIXING HELIXES:
Push down the chuck sleeve by hand (picture 1); Connect the paddle into the spline shaft directly
(picture 2) and release the chuck sleeve (picture 3).
(picture 1) (picture 2) (picture 3)
2 › INTEX GR OUP M EGAMIXE R MAN UAL | w intex.com. au w intex.co m. au | . I NTE X GRO UP MEGAMI XER MANUA L › 3
BUILDING E XCE LLENCE
BUILDING E XCE LLENCE
ENSURE THAT THE MIXING HELIXES ARE FIRMLY HELD IN THE
CHUCK B EFORE STARTING OPERATION.
SWITCHING ON AND OFF:
By pressing the switch button the machine is brought into operation and it
stops when this is released.
PERMANENT RUN:
After switching the machine on, the machine can be help on by pressing the lock button.
To release and turn off, press then release the switch.
CHANGING GEAR (2 SPEED GEARBOX MODELS)
Ensure that the motor is turned of and rotation has stopped.
Depress the gear change slide button and shift to next gear position.
DISCONNECTING THE M14 THREADED MIXING-PADDLE:
Using a flat open-end wrench on the spindle flats of the mixing tool and machine spindle,
unthread the mixing-paddle from the spindle by turning it anti-clockwise.
MAINTENANCE
• Before use ensure the ventilation holes on the motor housing are clear and clean.
Periodically these vents should be cleaned out.
• After approx. 100 hours of operation, check the motor brushes and replace if necessary.
Clean the motor housing.
• After approx. 200 hours of operation, renew the grease filling in the gearbox.
To verify that the protective insulation remains intact, the machine much be subjected to a
technical safety test afterwards. For this reason, this work much be performed exclusively by
a professional workshop.
The unit should be stored in a dry place where it is protected against moisture.
4 › INTEX GR OUP M EGAMIXE R MAN UAL | w intex.com. au w intex.com.au | . INTEX GR OUP M EGAMIXE R MAN UAL › 5
Loading...