109
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
OOWWNNEERR’’SS MMAANNUUAALL
Krystal Clear™
Model 633T
Filter Pump
IMPORTANT
SAFETY RULES
Read, understand, and follow all
instructions carefully before
installing and using this product.
IIMMPPOORRTTAANNTT!!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance,
Visit www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
Don’t forget to try these other fine Intex products: pools, pool accessories,
inflatable pools and in-home toys, airbeds and boats available at fine
retailers or visit our website.
For illustrative purposes only.
109-***-R2-1212
109
SAVE THESE INSTRUCTIONS
Page 2
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
TTAABBLLEE OOFF CCOONNTTEENNTTSS
Warnings.......................................................................... 3
Parts List & Reference................................................... 4-6
Setup Instructions.......................................................... 7-9
Operating Instructions................................................... 10
Operating Time Table...................................................... 11
Pool Care and Chemicals............................................... 12-13
Long Term Storage......................................................... 13
Troubleshooting Guide................................................... 14
Common Pool Problems................................................ 15
General Aquatic Safety.................................................. 16
Limited Warranty............................................................. 17
Pool Safety Sign............................................................. 18
Intex Service Center Locations..................................... 19
109
SAVE THESE INSTRUCTIONS
Page 3
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
SSAAFFEETTYY RRUULLEESS
This product is for use with storable pools only. Do not use with permanently-installed
pools. A storable pool is constructed so that it is capable of being readily disassembled
for storage and reassembled to its original integrity. A permanently-installed pool is
constructed in or on the ground or in a building such that it cannot be readily
disassembled for storage.
CAUTION
WARNING
These product warnings, instructions and safety rules provided with the product represent
some common risks of water recreation devices and do not cover all instances of risk and
danger. Please use common sense and good judgement when enjoying any water activity.
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
• To reduce the risk of injury, do not permit children to use this product. Always
supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Assembly and disassembly by adults only.
• Risk of electric shock. Connect only to a grounding type receptacle, this product
is provided with a ground-fault circuit interrupter. If replacement of the plug or cord
is needed, use only identical replacement parts.
• Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
• The unit is provided with a ground-fault circuit interrupter (GFCI). To test the GFCI,
push the test button. The GFCI should interrupt power. Push the reset button, power
should be restored. If the GFCI fails to operate in this manner. The GFCI is
defective. If the GFCI interrupts power to the pump without the test button being
pushed, a ground current is flowing, indicating the possibility of an electric shock.
Do not use this pump. Disconnect the pump and have the problem corrected by a
qualified service representative before using.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
• To reduce the risk of electric shock, replace damaged cord immediately. Use a
qualified electrician to replace the cord.
• To reduce the risk of electric shock, do not use extension cords, timers, plug
adaptors or converter plugs to connect unit to electric supply; provide a properly
located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
• Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI
since the ALCI will not protect people.
• Position this product away from pool, so as to prevent children from climbing on it
and access the pool.
• Do not operate this product when pool is occupied.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT OR
OTHER SERIOUS INJURY OR DEATH.
109
SAVE THESE INSTRUCTIONS
Page 4
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
PPAARRTTSS LLIISSTT
1
9
4
5
13 14 15
2
11 12
8
6
PARTS LIST
3
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
10
7
16
109
SAVE THESE INSTRUCTIONS
Page 5
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
a
nd become familiar with all the parts.
When ordering parts, be sure to quote the model number and part numbers.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
1
2
3
4
5
6
7
8
REF. NO.
DESCRIPTION
QTY.
SPARE PART NO.
1
2
2
1
1
1
1
2
THREADED FILTER HOUSING COLLAR
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
VALVE O-RING
FILTER HOUSING COVER
FILTER HOUSING O-RING
FILTER CARTRIDGE (59905)
AIR RELEASE VALVE B (WITH O-RING)
PUMP HOSE WITH NUTS
10491
10460
10264
10490
11330
10725
11009
2
3
4
5
1
6
8
7
3
2
109
SAVE THESE INSTRUCTIONS
Page 6
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
PPAARRTTSS RREEFFEERREENNCCEE
PARTS REFERENCE (continued)
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
9
10
11 12 13 14 15
When ordering parts, be sure to quote the model number and part numbers.
9
10
11
12
13
14
15
16
REF. NO.
DESCRIPTION
QTY.
SPARE PART NO.
2
2
2
2
1
1
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
HOSE O-RING
STEP WASHER
STRAINER NUT
FLAT STRAINER RUBBER WASHER
THREADED STRAINER CONNECTOR
ADJUSTABLE POOL INLET NOZZLE
STRAINER GRID
10747
10262
10745
10256
10255
10744
11074
10253
9
10
11 12 13 14
16
109
SAVE THESE INSTRUCTIONS
Page 7
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
1. Grasp the strainer and plunger valve
mechanism.
2. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 1). Be
careful not to lose the step rubber
washer (11). Place the plunger valve on the
ground in a safe place.
3. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat
washer (13) on the connector (14).
4. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert
the connector (14) into one of the pre-cut
holes with the washer remaining on the
connector to be placed against the inside
of the liner wall.
5. Before assembly, lubricate the threads
with a petroleum jelly. Then, with the flat
side of the strainer nut (12) facing the
outside wall of the liner in a clockwise
motion screw the strainer nut (12) back onto
the threaded connector (14) (see
drawing 2).
6. Finger tighten the strainer nut (12) onto the
threaded connector (14).
7. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
8. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 3).
9. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. not, grasp the handle at the top
and push down turning the handle in a
clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from flowing
out during filling of the pool (see
drawings 4.1 & 4.2).
The strainer grid prevents large objects from jamming and/or damaging the
filter pump. The plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. If your pool
h
as inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The parts numbers here onward, refer to the
parts depicted in the Parts List section of this manual. To install, do the
following:
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP
1
2
3
4.1
4.2
13 14 16
INSIDE
LINER WALL
INSIDE
LINER
WALL
12
2
1
1
2
1
2
109
SAVE THESE INSTRUCTIONS
Page 8
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
POOL INLET - NOZZLE & PLUNGER VALVE SETUP
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
5
7
8.1
8.2
INSIDE
LINER
WALL
POOL
9
2
1
1
2
1
2
6
13 14 15
INSIDE
LINER WALL
12
WATER
FLOW
1. Grasp the nozzle and plunger valve
mechanism.
2. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14) (see drawing 5). Be
careful not to lose the step rubber
washer (11). Place the plunger valve on the
ground in a safe place.
3. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat washer (13)
on the connector (14).
4. Install the nozzle and plunger valve at the
upper position of the pool inlet. From the
inside of the pool liner insert the
connector (14) into one of the pre-cut holes
with the washer remaining on the connector
to be placed against the inside of the liner
wall.
5. Before assembly, lubricate the threads with
a petroleum jelly. Then, with the flat side of
the strainer nut (12) facing the outside wall
of the liner in a clockwise motion screw the
strainer nut (12) back onto the threaded
connector (14) (see drawing 6).
6. Finger tighten the adjustable pool inlet
nozzle (15) and the strainer nut (12) onto
the threaded connector (14).
7. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
8. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 7).
9. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the handle
in a clockwise direction until the plastic
protruding notch anchors in the "0/1"
position. This will prevent water from
flowing out during filling of the pool (see
drawings 8.1 & 8.2).
10. Adjust the direction of the nozzle head
pointing away from the pool outlet for a
better circulation result (see drawing 9).
11. The pool liner is now ready to be filled with
water. Consult the above-ground-pool
owner’s manual for the filling instructions.
109
SAVE THESE INSTRUCTIONS
Page 9
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
SSEETTUUPP IINNSSTTRRUUCCTTIIOONNSS
FILTER PUMP HOSE CONNECTION SETUP
1. Remove the Krystal Clear™ filter pump and hoses from the packaging.
2. Place the filter pump in such a manner, that you can easily assemble the
hose (8) connections to the plunger valve.
N
ote: Some regional regulations may require the filter pump to be
mounted on a stationary platform. There are two mounting holes located
in the pump base for this reason. Consult your local authorities for
filter-pump mounting requirements.
3. Grasp the two pump hoses (8) and connect the hose nuts to the filter pump.
4. In a counter-clockwise motion unscrew the threaded filter housing collar (1)
from the filter housing. Place it in a safe place.
5. The Filter Pump is an airtight system. In a counter-clockwise motion turn both
air release valves (2 & 7) 1 - 2 turns to open.
DO NOT remove air release valves as water will expel with force if the
motor is turned on and injury may occur.
6. Grasp and remove the filter housing cover (4). Check to see if a cartridge is
inside the housing. If yes, replace the cover, finger tighten the housing collar (1)
back onto the filter housing.
7. Gently finger tighten the sediment release valve located at the bottom of the
housing to be sure that water does not leak out.
8. When the pool is filled connect the hose from the bottom of the filter housing to
the highest strainer assembly. You will find the hose connection at the bottom of
the plunger valve assembly. Use the hose nut to attach the hose.
9. Connect the second hose which is fixed to the middle of the motor housing to
the remaining liner connection.
WARNING
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
WATER LEVEL
ADJUSTABLE POOL
INLET NOZZLE
PLUNGER VALVE
ASSEMBLY
HOSE NUT
OUTLET HOSE
INSIDE
LINER WALL
THREADED
STRAINER
CONNECTOR
FILTER HOUSING
COLLAR
FILTER CARTRIDGE
INSIDE
FILTER HOUSING
COVER
AIR RELEASE
VALVE
MOTOR
HOUSING
HOSE O-RING
POWER CORD
INLET HOSE
OUTSIDE
LINER WALL
(ILLUSTRATION NOT TO SCALE)
W
A
T
E
R
F
L
O
W
W
A
T
E
R
F
L
O
W
HOSE O-RING
109
SAVE THESE INSTRUCTIONS
Page 10
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
OOPPEERRAATTIINNGG IINNSSTTRRUUCCTTIIOONNSS
1
. Make sure the filter pump is switched off. The switch is located on the motor
housing.
2. Connect the power cord to a GFCI protected electrical outlet.
3. Grasp a plunger valve handle. Turn the handle counter-clockwise, pull up until
it stops, and then turn it clockwise until the metal protruding notch anchors in
the "0/1" position. Repeat for the second plunger valve. This opens the valves,
allowing water to flow into the filter pump.
4. With water flowing into filter pump, the water pressure will allow the air trapped
inside to escape from the air release valves (2 & 7). When all the air has
escaped water will flow out of the valves (2 & 7). When this occurs gently finger
tighten the valves (2 & 7) in a clockwise direction.
5. To operate the filter pump on “TIMER” mode:
A. Set the timer dial to the desired operating hours. See operation time table.
See Fig. 10
B. Turn on the pump by pressing the switch to “ ” position, the filter pump is
now filtering the water and will stop after the operating hours are
completed. The built-in timer will now operate for the number of hours
selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “I” position, the filter pump is
now filtering the water.
B. To turn off the pump, press the switch to “O” position.
To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open the
air release valves, wait until water starts to flow out of the air release
valves, close air release valves.
IMPORTANT
Risk of electric shock. Connect this product only to a grounding type
receptacle protected by a ground-fault circuit interrupter (GFCI). Contact a
qualified electrician if you cannot verify that the receptacle is protected by
a GFCI.
WARNING
OPERATING INSTRUCTIONS
2
4
6
8
12
ON
OFF
TIMER
FIG 10
TIMER DIAL (HOURS)
109
SAVE THESE INSTRUCTIONS
Page 11
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
E
nglish
OPERATING TIME TABLE
This table shows the required operating time for average use of the filter pump with AGP's. The
filter pump running time should be 1 hour longer than the required operating time of the
Saltwater System.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80%
for Easy Set & Oval Pool)
100% Water
Capacity
Recommend
operating hours
per day
(
Gals)
(
Liters)
(
M
3
) (
Gals)
(
Hours)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET
®
POOL
CIRCULAR
METAL
FRAME POOL
ULTRA FRAME
POOL
SEQUOIA SPIRIT
®
POOL SET
OVAL FRAME
POOL
RECT. ULTRA
FRAME POOL
15' x 33" (457cm x 84cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 42" (488cm x 107cm)
16' x 48" (488cm x 122cm)
18' x 42" (549cm x 107cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
15' x 36" (457cm x 91cm)
15' x 42" (457cm x 107cm)
15' x 48" (457cm x 122cm)
16' x 48" (488cm x 122cm)
16' x 52" (488cm x 132cm)
18' x 48" (549cm x 122cm)
18' x 52" (549cm x 132cm)
20' x 48" (610cm x 122cm)
20' x 52" (610cm x 132cm)
24' x 48" (732cm x 122cm)
24' x 52" (732cm x 132cm)
16' x 48" (488cm x 122cm)
18' x 52" (549cm x 132cm)
22' x 52" (671cm x 132cm)
26' x 52" (792cm x 132cm)
16'8" x 49" (508cm x 124cm)
18'8" x 53" (569cm x 135cm)
18' x 10' x 42" (549cm x 305cm x 107cm)
20' x 12' x 48" (610cm x 366cm x 122cm)
24' x 12' x 48" (732cm x 366cm x 122cm)
28' x 12' x 48" (853cm x 366cm x 122cm)
28' x 12' x 52" (853cm x 366cm x 132cm)
18' x 9' x 52" (549cm x 274cm x 132cm)
24' x 12' x 52" (732cm x 366cm x 132cm)
32' x 16' x 52" (975cm x 488cm x 132cm)
2587
2822
3284
3736
3754
4273
4786
5455
5894
3282
3861
4440
5061
5501
6423
6981
7947
8638
11483
12481
5061
6981
10472
14667
5061
6981
2885
4393
5407
6420
6925
4545
8080
14364
9792
10681
12430
14141
14209
16173
18115
20647
22309
12422
14614
16805
19156
20821
24311
26423
30079
32695
43463
47241
19156
26423
39637
55515
19156
26423
10920
16628
20465
24300
26211
17203
30583
54368
12.2
13.4
15.5
17.7
17.8
20.2
22.6
25.8
27.9
13.8
16.2
18.7
21.3
23.1
27.0
29.4
33.4
36.3
48.3
52.5
21.3
29.4
44.0
61.7
21.3
29.4
13.7
20.8
25.6
30.4
32.8
19.1
34.0
60.4
3233
3527
4105
4671
4692
5342
5983
6819
7367
3647
4290
4934
5623
6112
7136
7757
8830
9598
12758
13868
5623
7757
11635
16297
5623
7757
3607
5491
6758
8025
8657
5050
8978
15960
2
2
2
2
2
4
4
4
4
2
2
2
4
4
4
4
4
4
6
6
4
4
6
8
4
4
2
4
4
4
4
4
4
8
109
SAVE THESE INSTRUCTIONS
Page 12
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
MMAAIINNTTEENNAANNCCEE
POOL CARE AND CHEMICALS
CLEANING OR REPLACING FILTER CARTRIDGES
• All pools require care to keep the water clear and hygienically clean. With
proper chemical control, your filter will help attain this objective. Consult your
pool supply dealer for instructions regarding the proper use of chlorine,
a
lgaecide and other chemical agents required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations
could occur.
• Daily pH checking and chemical treatment of the water is very important and
can not be overemphasized. Chlorine, algaecide and maintenance of proper pH
levels are required when filling the pool as well as during the season. Consult
your local swimming pool supply store for instructions.
• The season's first filling of the pool may have brackish water requiring extra
water additives and extra filter changes. Do not allow swimming in pool until the
pH level is balanced. Consult your local swimming pool supply store for
instructions.
• Keep spare filter cartridges on hand. Replace cartridges every two weeks.
• Chlorinated water may damage lawns, gardens or shrubbery as children play
in the pool and splash water outside the pool. Lawn areas underneath the
pool liner will be destroyed. Note that some types of grass may grow through
the liner.
• Filter run time depends on pool size, weather and usage level. Experiment with
various run times so as to produce clean clear water.
It is recommended that the filter cartridge be replaced at least
every 2 weeks.
1. Make sure the filter pump is turned off, then disconnect the power cord from
the electrical outlet.
2. Close both plunger valves. Grasp a plunger valve handle. Turn the handle
counter-clockwise, push down until it stops and then turn it clockwise until the
plastic protruding notch anchors in the "0/1" position. Repeat for the second
plunger valve. This prevents the water from flowing out of the pool.
3. Gently turn the top air release valve once or twice in a counter-clockwise
direction. The housing cover can now be easily removed.
4. In a counter-clockwise direction remove the filter housing collar (1). Place it in a
safe location.
5. Remove the housing cover (4).
6. Now remove the used filter cartridge.
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always
follow the chemical manufacturer’s directions, and the health and hazard
warnings.
109
SAVE THESE INSTRUCTIONS
Page 13
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
MMAAIINNTTEENNAANNCCEE
CLEANING OR REPLACING FILTER CARTRIDGES (continued)
LONG TERM STORAGE
1. Before emptying your pool for long term storage, or relocation, be sure the
water is directed towards an acceptable drain water receptacle away from the
house. Check local regulations for specific directions regarding disposal of
swimming pool water.
2. Disconnect power cord from electrical outlet.
3. Now, drain the pool.
4. When the pool is empty, disconnect all hoses from pump and plunger valves
and remove the strainers from the pool wall.
5. Drain all water from the filter pump.
6. Leave filter pump pieces & hoses outside to thoroughly air dry.
7. Twist the plunger collar counter-clockwise removing the water flow control
mechanism from the plunger housing.
8. Coat the following O-rings and washers with petroleum jelly for long term
storage:
• Air release valve & sediment O-rings (3).
• Filter housing cover O-ring (5).
• Pump hose O-rings (10).
• Strainer valve assembly step washers (11).
• Flat strainer rubber washers (13).
9. Discard the used filter cartridge. Put aside 1 or 2 new cartridges for next
season’s use.
10. It is best to place all dry pieces in the original packaging for storage or place
them in an airtight plastic bag.
11. Store the unit and accessories in a dry place. The storage's temperature should
be controlled, between 32 degrees Fahrenheit (0 degrees Celsius) and 104
degrees Fahrenheit (40 degrees Celsius) storage location.
7. Examine the inside of the filter housing.
8
. If dirt or sediment is located on the bottom of the housing then:
A. In a counter-clockwise motion gently unscrew and remove the sediment
valve (2) located at the bottom of the housing. Place it in a safe place.
B. With a bucket of water or a garden hose pour water into the housing
flushing out the sediment.
C. Screw back the sediment valve (2) in a gentle clockwise motion. Do not
over-tighten.
9. Place a new cartridge filter in the housing.
10. Return the housing cover (4) to its position and in a clockwise direction rescrew
the housing collar (1) onto the filter housing.
11. Turn both plunger valve handles in a counter-clockwise direction, pull up until
they stop, and then turn them clockwise until the metal protruding notch
anchors in the "0/1" position.
12. When the trapped air has escaped through the air release valve gently
retighten the valve (2) in a clockwise direction.
13. Reconnect the power cord.
14. Turn on the pump.
IMPORTANT
It is best to store away your poolsystem in its original packaging.
109
SAVE THESE INSTRUCTIONS
Page 14
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
TROUBLESHOOTING GUIDE
TTRROOUUBBLLEESSHHOOOOTTIINNGG GGUUIIDDEE
IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.
• Filter cord must be plugged into a 3 wire
outlet that is protected by a Class A
G
round Fault Circuit Interrupter.
• Reset circuit breaker. If circuit breaker trips
repeatedly, your electrical system may
have a defect. Turn off circuit breaker and
c
all an electrician to correct the problem.
• Let motor cool down.
• Adjust the chlorine and pH level. Consult
your local swimming pool supply stores.
• Clean or replace cartridge.
• Check the cartridge for holes. Replace if
damaged.
• Operate the filter for longer periods.
• Clean the strainer screen at the inlet.
• Clear any obstructions in the intake hose by
discharging it inside pool wall.
• Tighten hose nuts, check hoses for
damage, check pool water level.
• Clean cartridge more often.
• Clean inside the plunger valve.
• Pull valve handle to full upright position.
• Install the nozzle at the upper position of
pool inlet, and the strainer at the lower
position of pool outlet.
• Fill pool to correct water level.
• Clean strainer screens at pool inlet.
• Tighten hose nuts, check hose for damage.
• Clear any sticks or leaves in the intake
hose.
• Turn and pull valve handle to full upright
position.
• Remove cover & check for O-ring.
• Tighten cover (Manually).
• Replace or clean cartridge.
• Tighten or reinstall hose nut.
• Open air release valve, wait until water
starts to flow out of the valves, then
close it.
• The lower position of pool outlet connects
to filter pump water inlet. The upper position
of pool inlet connects to filter pump water
outlet.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
THE WATER
FLOW IS VERY
SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
HOSE LEAKING
AIR LOCK
• The motor is not plugged in.
• The fuse box needs checking.
• The GFCI circuit breaker
is tripped.
• Motor too hot and overload
protection shut motor off.
• Improper chlorine or pH
levels.
• Filter cartridge is dirty.
• Damaged cartridge.
• Excessively dirty pool.
• The strainer screen is
restricting the water flow.
• Clogged inlet or discharge.
• An air leak on the intake line.
• Scale or buildup on cartridge.
• Excessively dirty pool.
• Dirty filter cartridge.
• The nozzle and strainer
connection are reversed.
• Low water level.
• Strainer screen plugged up.
• An air leak on the intake hose.
• Faulty motor or the impeller
is jammed.
• An air lock inside the cartridge
chamber.
• O-ring missing.
• Cover is not tight.
• Filter cartridge is dirty.
• Hose nuts are not well-fitted.
• There’s air trapped in the
pump housing and inlet hose.
• The inlet and outlet hoses
connection are reversed.
TROUBLE CAUSE SOLUTION
109
SAVE THESE INSTRUCTIONS
Page 15
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
COMMON POOL PROBLEMS
CCOOMMMMOONN PPRROOBBLLEEMMSS
P
ROBLEM DESCRIPTION CAUSE SOLUTION
ALGAE
COLORED
WATER
FLOATING
MATTER IN
WATER
CHRONIC
LOW WATER
LEVEL
SEDIMENT
ON POOL
BOTTOM
SURFACE
DEBRIS
• Chlorine and pH levels
n
eed adjustment.
• Copper, iron or maga
nese in water being
oxidized by the added
chlorine.
This is common.
• "Hard water" caused
by a too high pH level.
• Chlorine content is low.
• Foreign matter in
water.
• Rip or hole in pool
liner or hoses.
• The drain valves are
loose.
• Heavy use, getting in
and out of pool.
• Pool too close to
trees.
• Super chlorinate with shock
t
reatment. Correct pH to your
pool store's recommended
level.
• Vacuum pool bottom.
•
Maintain proper chlorine
level.
• Adjust pH level to the
recommended level.
• Run filter until water is clear.
• Clean cartridge frequently.
• Correct the pH level. Check
with your pool dealer for
advice.
• Adjust the chlorine level.
• Clean or replace your filter.
• Repair with a patch kit.
• Finger tighten all caps.
• Use Intex pool vacuum to
clean bottom of pool.
• Use Intex pool skimmer.
• Greenish water.
•
Green or black
spots on pool liner.
• Pool liner is
slippery and/or has
a
bad odor.
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Water is cloudy or
milky.
• Level is lower than
on previous day.
• Dirt or sand on
pool floor.
• Leaves, insects
etc.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
109
SAVE THESE INSTRUCTIONS
Page 16
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
SSAAFFEETTYY GGUUIIDDEELLIINNEESS
GENERAL AQUATIC SAFETY
Water recreation is both fun and therapeutic. However, it involves
inherent risks of injury and death. To reduce your risk of injury, read
and follow all product, package and package insert warnings and
instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation,
but do not cover all instances or risk and or danger.
For additional safeguards, also familiarize yourself with the following
general guidelines as well as guidelines provided by nationally
recognized Safety Organizations:
• Demand constant supervision.
• Learn to swim.
• Take the time to learn CPR and first aid.
• Instruct anyone who is watching your children about potential pool
hazards and about the use of protective devices such as locked doors,
barriers, etc.
• Teach children what to do in case of an emergency.
• Always use common sense and good judgement when enjoying any
water activity.
• Supervise, supervise, supervise.
For additional information on safety, please visit
• The Association of Pool and Spa Professionals: The Sensible Way to
Enjoy Your Aboveground/Onground Swimming Pool www.nspi.org
• American Academy of Pediatrics: Pool Safety for Children www.aap.org
• Red Cross www.redcross.org
• Safe Kids www.safekids.org
• Home Safety Council: Safety Guide www.homesafetycouncil.org
• Toy Industry Association: Toy Safety www.toy-tia.org
SAFETY IN YOUR POOL
Safe swimming depends on constant attention to the rules. The "NO DIVING"
sign within this manual can be posted near your pool to help keep everyone
alert to the danger. You may also wish to copy and laminate the sign for
protection from the elements.
109
SAVE THESE INSTRUCTIONS
Page 17
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
E
nglish
PARTS LIST
Your Krystal Clear™ Filter-Pump has been manufactured using the highest quality
materials and workmanship. All Intex products have been inspected and found free of
defects prior to leaving the factory. This Limited Warranty applies only to the Krystal Clear™
Filter-Pump and accessories listed below.
The provisions of this Limited Warranty apply only to the original purchaser and is not
transferable. This Limited Warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this manual, as proof of
purchase will be required and must accompany warranty claims or the Limited Warranty is
invalid.
Krystal Clear™ Filter-Pump Warranty – 2 Years
Hoses, Plunger Valves & Fittings Warranty – 180 days
If a manufacturing defect is found within the periods noted above, please contact the
appropriate Intex Service Center listed in this manual. The Service Center will determine the
validity of the claim. If the Service Center directs you to return the product, please carefully
package the product and send with shipping and insurance prepaid to the Service Center.
Upon receipt of the returned product, the Intex Service Center will inspect the item and
determine the validity of the claim. If the provisions of this warranty cover the item, the item
will be repaired or replaced at no charge.
Any and all disputes regarding the provisions of this Limited Warranty shall be brought
before an informal dispute settlement board and unless and until the provisions of these
paragraphs are carried forth, no civil action may be instituted. The methods and
procedures of this settlement board shall be subject to the rules and regulations set forth by
the Federal Trade Commission (F.T.C.). IMPLIED WARRANTIES ARE LIMITED TO THE
TERMS OF THIS WARRANTY AND IN NO EVENT SHALL INTEX, THEIR AUTHORIZED
AGENTS OR EMPLOYEES BE LIABLE TO THE BUYER OR ANY OTHER PARTY FOR
DIRECT OR CONSEQUENTIAL DAMAGES OR LIABILITIES. Some states, or jurisdictions
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This Limited Warranty does not apply if the products are subject to negligence, abnormal
use or operation, accident, improper operation, improper voltage or current contrary to
operating instructions, or to damage by circumstances beyond Intex’s control, including but
not limited to, ordinary wear and tear and damage caused by exposure to fire, flood,
freezing, rain, or other external environmental forces. This Limited Warranty applies only to
those parts and components sold by Intex. The Limited Warranty does not cover
unauthorized alterations, repairs or disassembly by anyone other than Intex Service Center
personnel.
DO NOT GO BACK TO THE PLACE OF PURCHASE FOR RETURN
OR REPLACEMENT. IF YOU ARE MISSING PARTS OR NEED
ASSISTANCE, PLEASE CALL US TOLL-FREE (FOR U.S. AND
CANADIAN RESIDENTS): 1-800-234-6839 OR VISIT OUR WEBSITE:
WWW.INTEXSTORE.COM.
Proof of Purchase must accompany all returns or the warranty claim will be invalid.
LIMITED WARRANTY
109
SAVE THESE INSTRUCTIONS
Page 18
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
E
nglish
• UNITED STATES INTEX RECREATION CORP.
• CANADA 1665 Hughes Way
L
ong Beach, CA 90801
Tel: 1-800-234-6839
Fax: 310-549-2900
Website: www.intexcorp.com (U.S./Canada only)
Consumer Service Hours: 8:30 am to 5:00 pm
Pacific Time, Mon. thru F
RI. only.
• MEXICO KAY INTERNACIONAL, S.A. DE C.V.
Avenida San Jeronimo #550-5° Piso, Col.
J
ardines del Pedregal, C.P. 01900
México D.F.
Tel: 01-800-347-4020 (Collect Call)
Tel: 55-9172-8035
Fax: 55-9172-8047
E-mail: servicenter@kayinternacional.com
Website: www.intexmexico.com.mx
• PANAMA SUPRO MUNDIAL S.A./
• PARAGUAY PRODUCTOS SUPERIORES S.A.
• ECUADOR Boulevard Andrews, Albrook,
• HONDURAS Panama, Rep. of Panama
• EL SALVADOR Tel: 507-300-3800
• NICARAGUA Fax: 507-300-3813
E-mail: suproadmin@supropanama.com
• COSTA RICA CENTURY USA, LLC
• DOMINICAN REPUBLIC 4731 W. Atlantic Ave., Suite B-3
• GUATEMALA Delray Beach, FL 33445, USA
• COLOMBIA Tel: 561-495-0648
• VENEZUELA Fax: 561-495-4782
E-mail: sales@centuryusa.com
• MIDDLE EAST REGION FIRST GROUP INTERNATIONAL
Al Moosa Group Building, 1st Floor,
Office 102 & 103, UMM Hurair Road,
Karama, Dubai, UAE
Tel: 00971-4-3373322
Fax: 00971-4-3375115
E-mail: info@firstgroupinternational.com
Website: www.firstgroupinternational.com
• ASIA INTEX DEVELOPMENT CO. LTD.
8th Floor,
Dah Sing Financial Centre
108 Gloucester Road,
Wanchai, Hong Kong
Tel: 852-28270000
Fax: 852-23118200
E-mail: xmservicesupport@intexcorp.com.cn
Website: www.intexdevelopment.com
For answers to most frequently asked questions, please visit www.intexcorp.com.
Non U.S. Residents, please visit www.intexdevelopment.com.
COUNTRIES/REGIONS SERVICE CENTER LOCATIONS
(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 12/01/2011
English
For Residents of the U.S. & Canada:
INTEX RECREATION CORP.
Attn: Consumer Service
1665 Hughes Way
Long Beach, CA 90801
Phone: 1-800-234-6839
Fax: (310) 549-2900
Consumer Service Hours:
8:30 am to 5:00 pm Pacific time
Monday thru Friday only
Website: www.intexcorp.com
For Residents outside of the U.S. and Canada:
Please refer to the Service Center Locations
I N T E X
®
©2011 Intex Marketing Ltd. - Intex Development Co. Ltd. Intex Trading Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los
derechos reservados/Alle Rechte vorbehalten.
Printed in China/Imprimé en Chine/Impreso en
China/Gedruckt in China.
®™ Trademarks used in some countries of the world under
license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países
del mundo bajo licencia de/Warenzeichen verwendet in
einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd.
to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd.,
G.P.O Box 28829, Hong Kong & Intex Recreation Corp.,
P.O. Box 1440, Long Beach, CA 90801 • Distributed in the
European Union by/Distribué dans l’Union Européenne
par/Distribuido en la unión Europea por/Vertrieb in der
Europäischen Union durch/Intex Trading B.V., P.O. Box nr.
1075 – 4700 BB Roosendaal – The Netherlands
Loading...