Intex JR. TWIN ROLL´N GO AIRBED KIT User Manual

(69PO) 3 IN 1 VALVE ENGLISH 4.875” X 7.25” 10/21/2013

3 IN 1 VALVE INSTRUCTION

Quick-inflation cap

Quick-inflation cap O-ring

Quick-exhaust cap

TO INFLATE WITH QUICK-INFLATION VALVE

1. Ensure the quick-exhaust and the optional inflation caps are securely tightened.

2. Turn the quick-inflation cap fully counterclockwise. See Fig 1-a.

3. Pull the quick-inflation cap to open. See Fig 1-b.

4. Insert the inflation opening of an air pump directly into the quick-inflation valve. See Fig 2.

5. Inflate the product to approximately 80% of desired firmness. CAUTION: To prevent

bursting, do not over inflate or use high pressure air compressor.

6. Align the two " " on the cap with the arrows on both side of the quick-exhaust cap tabs and push in firmly. See Fig 3-a.

7. Turn the quick-inflation cap fully clockwise to close. See Fig 3-b.

69PO

TO INFLATE WITH OPTIONAL INFLATION

Optional inflation cap

VALVE

8. Ensure the quick-exhaust and the quick-inflation caps are

Quick-exhaust cap O-ring

securely tightened.

9. Pull the optional inflation cap

Rubber diaphragm

tab to open. See Fig 4.

Fig 4

10. Insert the nozzle of an air pump into the inflation valve. See Fig 5.

11. Inflate the product to approximately 80% of desired firmness. CAUTION: To prevent

bursting, do not over inflate or use high pressure air compressor.

Fig 1

12. Close the optional inflation cap

Fig 5

securely after inflation. See Fig 6.

TO ADJUST

13. If the product is too firm, open the quick-inflation cap, repeat

Fig 6

Fig 2

steps #2 and #3.

14. Gently press one of the 3 protruding tabs on the quick-inflation valve to release a small amount of air. CAUTION: Do not bend or

fold down the black rubber diaphragm. See Fig 7.

15. When the desired firmness is achieved, replace the quick-inflation cap back. See

Fig 3

Fig 3.

Fig 7

SAVE THESE INSTRUCTIONS

Page 1

069-*PO-R0-1410

SAVE THESE INSTRUCTIONS

Page 2

TO DEFLATE

16. Press the two tabs inwards on each side of the quick-exhaust cap and pull outwards to open. See Fig 8 - 9.

(69PO) 3 IN 1 VALVE ENGLISH 4.875” X 7.25” 10/21/2013

69PO 69PO69PO

Fig 8

Fig 9

17. For packaging purpose, you may use an air pump to remove the remaining air completely from the airbed. See Fig 10.

Fig 10

CLICK

"CLICK"

Fig 11

18. When the product is completely deflated, replace the quick-exhaust cap back. See Fig 11-a & 11-b.

IMPORTANT: Press down both tabs to ensure the "quick-exhaust cap" is firmly secured onto the sitting base. Notice the "CLICK" sound from both tabs.

©2013 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd. - Intex Recreation Corp. All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle Rechte vorbehalten. Made in China/Fabriqué en Chine/Hecho en China/Hergestellt in China.

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex

Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V.,

�

Venneveld 9, 4705 RR Roosendaal – The Netherlands Consumer Service 1-800-234-6839 www.intexcorp.com

SAVE THESE INSTRUCTIONS

Page 3