InterVac F-120, H-120, CM-120 Installation And Operating Manual

interVac~

RECORD THIS INFORMATION FOR
FUTURE REFERENCES

MODEL NUMBER _
DATE OF PURCHASE _
PLACE OF PURCHASE _

DESIGN CORP

THE BUILT-IN VACUUM SYSTEM

Manual # F-H-CM-e, Rev.:05/08
Part#W500

INSTALLATION AND OPERATING MANUAL

MODEL F-120

for flush mounting inside a wall only

MODEL H-120

for surface mounting against a wall only

MODEL CM-120

for surface mounting or converting to flush mounting

C@US

USTED

Important: Instructions must stay with unit. Owner read carefully.

WARNING:

This manual must be read and understood before installation, adjustment, service or

maintenance is performed. This unit should be installed by a qualified technician.

Modification of this product can be extremely hazardous and could result in

personal injury or property damage.

InterVac Design Corp., Palm City, FL 34990

Phone [phone] • Toll Free 1-888-499-1925

www.intervacdesign.com • e-mail: [e-mail]

1

interVac-1

IMPORTANT SAFETY INSTRUCTIONS

Polarization Instructions for models H120 and CM120 (with cord) only.
These appliances have a polarized plug (one blade is wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

When using an electrical vacuum cleaner, basic precautions should always be followed including the following:
Read all instructions carefully before using this vacuum cleaner.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

1. Do not leave appliance when plugged in. Unplug from an
electrical outlet when not in use and before servicing.

2. Do not use outdoors or on wet surfaces.

3. Never operate this vacuum cleaner without a dust bag and filters
in place.

4. Close attention is necessary when used by or near children .00
not allow unit to be used as a toy.

5. Use only for intended use as described in this manual. Use only
the manufacturer's recommended attachments and dust bag.

6. Do not use with damaged cord or plug. Ifappliance is not working

as itshould, has been dropped, damaged, left outdoors, orfell into
water, return the vacuum cleaner to InterVac or an authorized
service dealer for examination and repair.

7. Do not put any object into openings. Do not use with any openings

blocked; keep free of dust,lint, hair and any other material that
may reduce air flow. When the secondary filter becomes dirty,
rinse in warm water or replace with a new filter. Filter should be
completely dry before using.

8. Never drop or insert any object into any opening.

9. Turn off all controls before unplugging.

10.

Do not pull or carry by cord, do not use cord as a handle, do not
close adooron the cord, orpull cord around sharp edges or
corners. Do not run appliance over cord. Keep cord away from
heated surfaces.

11. Do not unplug by pulling on cord. To unplug, grasp the plug, not
the cord.

12. Keep hair, loose clothing, fingers, and all parts of body away

from any openings and all moving parts.

13. Do not pick up anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

14. Use extra caution when cleaning on stairs.

15. Do not handle plug or appliance with wet hands.

16. Do not pick up flammable or combustible liquids such as

gasoline, or use in areas where they may be present.

17. Do not place objects against the vacuum cleaner. Keep area

clear.

18. Do not step on the hose or pull the hose forcibly.

19. Do not pick up large objects such as waste paper or cloth,

which may clog the hose.

20. Do not install this vacuum cleaner in an area exposed to high

temperatures.

21. Install this vacuum cleaner in a dry place.

22. Do not attempt to service the vacuum cleaner. Unit is sealed

and can not be opened without damage to the unit. For service,
call your local authorized service dealer, or InterVac Design's
Customer Care Center.

SAVE THESE INSTRUCTIONS

LIMITED WARRANTY

InterVac Design Corp. will repair the power unit with new or rebuilt parts, free of charge for seven (7) years from the date of
original purchase inthe event of a defect in materials or workmanship. No cash refunds. Excluded are the following items that
require normal replacement:

Disposable dust bags, filters, vacuum cleaner tools and vacuum hoses.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original purchase will be
required before warranty performance is rendered.
You must return your warranty card or registeron our website in orderto be covered under these provisions.
This warranty only covers failures due to defects in materials or workmanship which occurs during normal use and does not
cover damage which occurs in shipment or failures which are caused by products not supplied by InterVac Design, or failures
which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, or commercial use
such as hotel, office, restaurant or rental use of the product, or service by anyone other than an authorized service center, or
damage that is attributable to acts of God.
There are no expressed warranties except as listed above.

LIMITS AND EXCLUSIONS:

INTERVAC DESIGN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESSED AND

IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO THEAPPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an

implied warranty last, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights
that vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your
dealer or our service center. Ifthe problem is not handled to your satisfaction, than write to the Customer Service Center at the
company address.

2

interVac-

MODEL: H120 or CM120
surface mounted with power cord attached

TIP: if you do not like to surface mount the vacuum with screws you can use Velcro, ask for our kit

#

A015

External to Wood Surfaces: (see Fig.: A)

Step 1.

Step 2.

Step 3.
step 4.

TIP:

Step 5.

To cover with the vacuum hose as much area as possible, choose a wall or surface that is centrally located

and has an electrical outlet close by.

Cut paper template from instruction manual, page 8. Tape the template to the wall or a surface at a comfortable
operating height or a minimum of 6 inches above the floor. Mark the 4 centers accurately.
Carefully remove template from the wall and place it into the operating manual for future references.

Attach the enclosed #8 screws to the wall as marked on the template. Keep the screw heads 1/8" from the wall.
Slide the key holes on the back of the vacuum cleaner over the 4 screw heads and secure by pushing down.

If vacuum cleaner is loose re-tighten screws.

If vacuum cleaner is mounted on its back or side or very low, it may slide off the screw heads when you pull too hard on the

vacuum hose. To prevent this, fasten a small block against the top of the unit.

Check to be sure dust bag and motor filter (under dust bag) are in place.

External to Drywall (% thick) Surfaces: (see Fig.: A)

Step 1.

Step 2.

Step 3.

Step 4.
Step

5.

Step 6.

Step 7.
Step 8.

Step 9.

TIP:

To cover with the vacuum hose as much area as possible, choose a wall or surface that is centrally located

and has an electrical outlet close by.
Tape the paper template #W600 on page 8 to a wall at a comfortable operating height or a minimum of 6 inches
above the floor.
With an awl or similar object mark the center of the key holes accurately. Carefully remove template from the
wall and place it into the operating manual for future references.
With a 3/32 drill bit, pre-drill all 4 holes.

Now use a 5/16 drill bit to enlarge the 4 holes to the correct size.
Squeeze the two arms of the anchor together and insert through the hole. Very lightly hammer the anchor

flush with the dry-wall surface.

Insert the red key-pin to toggle the anchor open behind the dry-wall, remove red key. Do not hammer key.

Attach the four screws (#8) through the anchors into the wall. Keep the screw heads 1/8" from the

wall surface.
Slide the key holes on the back of the vacuum cleaner over the 4 screw heads and push down.
If the vacuum cleaner is loose on the screws re-tighten screw heads a little more.
If vacuum cleaner is mounted on its back or side or very low, it may slide off the screws heads when you pull too hard on the

vacuum hose. To prevent this, fasten a small wood block against the top of the unit.

Fig.: A

Minimum height 6" from floor

Fig.: B

Paper Template: # W600 see page 8

for surface mounting

Tape template to wall

Paper Template: # W601 or # W602

for flush mounting

3