intersil ISL29000 DATA SHEET

查询ISL29000供应商
®
ISL29000
Data Sheet June 20, 2005
Ambient Light Photo Detect IC
The ISL29000 is a light-to-current optical sensor combining a photodiode and a current amplifier on a single monolithic IC. Output current is directly proportionate to the light intensity on the photodiode. Its sensitivity is superior to that of a phototransistor and exhibits little variation. Its spectral sensitivity matches closely to the luminous efficiency and linearity.
Housed in an ultra-compact surface mount clear plastic package, this device is excellent for power saving control function in cell phones, PDAs, and other handheld applications.
Pinout
ISL29000
(5-PIN DFN)
TOP VIEW
VCC
OUTPUT
FN6117.0
Features
• Monolithic IC containing photodiode and amplifier
• Converts light intensity to current
• 2.5V to 5.5V supply range
• Low supply current - 1µA
• Excellent output linearity of luminance
• Ultra-compact and light surface mount package
• Pb-Free plus anneal available (RoHS compliant)
Applications
• Mobile phones
• Notebook PCs
•PDAs
• Video cameras
• Digital cameras
Ordering Information
GND
EN
NC
PART NUMBER PACKAGE
ISL29000IROZ (See Note)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
5-Pin ODFN
(Pb-free)
TAPE &
REEL PKG. DWG. #
- MDP0052
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
All other trademarks mentioned are the property of their respective owners.
Copyright © Intersil Americas Inc. 2005. All Rights Reserved.
ISL29000
Absolute Maximum Ratings (T
Supply Voltage between V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . TBD
and GND . . . . . . . . . . . . . . . . . . . .6V
SD
= 25°C)
A
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = T
Electrical Specifications V
= 3V, TA = 25°C, fluorescent light, unless otherwise specified.
CC
A
PARAMETER DESCRIPTION CONDITION MIN TYP MAX UNIT
I
CC
Supply Current RL = 1k, EV = 1000lx 74 µA
EV = 0 0.2 µA
I
I
I
LEAK
V
O-MAX
T
T
T
T
V
V
L1
L2
R
F
D
S
LO
HI
Light Current EV = 1000lx 45 61 75 µA
Light Current EV = 100lx 6.5 µA
Dark Current EV = 0 0.06 µA
Maximum Output Compliance Voltage At 95% of normal output current,
2.7 V
EV = 1000lx
Rise Time (See Note) RL = 5k, EV = 1000lx 27 50 µs
Fall Time (See Note) RL = 5k, EV = 1000lx 78 110 µs
Delay Time for Rising Edge (See Note) RL = 5k, EV = 1000lx 80 110 µs
Delay Time for Falling Edge (See Note) RL = 5k, EV = 1000lx 35 50 µs
Maximum Voltage at EN Pin to Enable 0.6 V
Minimum Voltage at EN Pin to Disable 1.8 V
NOTE: Switching time measurement is based on Figures 1 and 2.
V
CC
PULSE
DRIVE
ISL29000
R
FIGURE 1. RISE/FALL TIME MEASUREMENT
PULSE DRIVE
CH1
T
D
1V
V
OUT
CH2
0.1V
V
OUT
T
R
L
100µs
T
S
VS=3V
=27°C
T
A
80%
20%
T
F
FIGURE 2.
2
FN6117.0
June 20, 2005
Loading...
+ 3 hidden pages