intersil ISL22316WMUEP DATA SHEET
®
www.BDTIC.com/Intersil
Single Digitally Controlled Potentiometer (XDCP™)
ISL22316WMUEP
Data Sheet December 17, 2007
Low Noise, Low Power I2C® Bus, 128 Taps
The ISL22316WMUEP integrates a single digitally controlled
potentiometer (DCP) and non-volatile memory on a
monolithic CMOS integrated circuit.
The digitally controlled potentiometer is implemented with a
combination of resistor elements and CMOS switches. The
position of the wipers are controlled by the user through the
2
I
C bus interface. The potentiometer has an associated
volatile Wiper Register (WR) and a non-volatile Initial Value
Register (IVR) that can be directly written to and read by the
user. The contents of the WR controls the position of the
wiper. At power-up, the device recalls the contents of the
DCP’s IVR to the WR.
The DCP can be used as a three-terminal potentiometer or
as a two-terminal variable resistor in a wide variety of
applications including control, parameter adjustments and
signal processing.
Device Information
The specifications for an Enhanced Product (EP) device are
defined in a Vendor Item Drawing (VID), which is controlled
by the Defense Supply Center in Columbus (DSCC).
“Hot-links” to the applicable VID and other supporting
application information are provided on our website.
Pinout
ISL22316WMUEP
(10 LD MSOP)
TOP VIEW
SCL
SDA
A1
A0
SHDN
1
2
3
4
5
10
V
CC
9
R
H
R
8
W
7
R
L
GND
6
FN6622.0
Features
• Specifications per DSCC VID V62/08603-01XB
• Full Mil-Temp Electrical Performance from -55°C to +125°C
• Controlled Baseline with One Wafer Fabrication Site and
One Assembly/Test Site
• Full Homogeneous Lot Processing in Wafer Fab
• No Combination of Wafer Fabrication Lots in Assembly
• Full Traceability Through Assembly and Test by
Date/Trace Code Assignment
• Enhanced Process Change Notification
• Enhanced Obsolescence Management
• Eliminates Need for Up-Screening a COTS Component
• 128 Resistor Taps
2
C Serial Interface
•I
- Two Address Pins, Up To Four Devices/Bus
• Non-volatile Storage of Wiper Position
• Wiper Resistance: 70Ω Typical @ 3.3V
• Shutdown Mode
• Shutdown Current 5µA Max
• Power Supply: 2.7V to 5.5V
•10kΩ Total Resistance
• High Reliability
- Endurance: 1,000,000 Data Changes Per Bit Per
Register
- Register Data Retention:
- 10 years @ T ≤ +125°C
- 15 years @ T ≤ +90°C
- 50 years @ T ≤ +55°C
•10 Ld MSOP
Ordering Information
VENDOR PART NUMBER
(Notes 1, 2) VENDOR ITEM DRAWING PART MARKING
ISL22316WMUEP V62/08603-01XB 2316M 10 -55 to +125 10 Ld MSOP M10.118
NOTES:
1. Add “-TK” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. Devices must be procured to the VENDOR PART NUMBER.
1
1-888-INTERSIL or 1-888-468-3774
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
RESISTANCE OPTION
(kΩ)
| Intersil (and design) and XDCP are registered trademarks of Intersil Americas Inc.
All other trademarks mentioned are the property of their respective owners.
TEMP.
RANGE (°C) PACKAGE
Copyright Intersil Americas Inc. 2007. All Rights Reserved
PKG.
DWG. #
Block Diagram
www.BDTIC.com/Intersil
ISL22316WMUEP
V
CC
SCL
SDA
A0
A1
SHDN
I2C
INTERFACE
POWER-UP
INTERFACE,
CONTROL
AND
STATUS
LOGIC
NON-VOLATILE
REGISTERS
GND
Pin Descriptions
MSOP PIN SYMBOL DESCRIPTION
2
1 SCL Open drain I
2 SDA Open drain Serial data I/O for the I2C interface
3 A1 Device address input for the I
4 A0 Device address input for the I
5SHDNShutdown active low input
6 GND Device ground pin
7R
8R
9R
10 V
L
W
H
CC
“Low” terminal of DCP
“Wiper” terminal of DCP
“High” terminal of DCP
Power supply pin
C interface clock input
2
C interface
2
C interface
WR
RH
RW
RL
2
FN6622.0
December 17, 2007
Loading...