intersil ICL3217E DATA SHEET
查询ICL3207E供应商
®
ICL3207E, ICL3217E
Data Sheet June 2004
+/- 15kV ESD Protected, +3V to +5.5V, Low
Power, 250kbps, RS-232
Transmitters/Receivers
The Intersil ICL32X7E devices are 3V to 5.5V powered
RS-232 transmitters (five)/receivers (three) which meet
ElA/TIA-232 and V.28/V.24 specifications, even at
V
= 3.0V. Additionally, they provide ±15kV ESD
CC
protection (IEC61000-4-2 Air Gap) and
Model protection on transmitter outputs and receiver inputs
(RS-232 pins). Targeted applications are ISDN Terminal
Adaptors, PDAs, Palmtops, peripherals, and notebook and
laptop computers where the low operational, and even lower
standby, power consumption is critical. The ICL3217E’s
efficient on-chip charge pumps, coupled with an automatic
powerdown function, reduces the standby supply current to
a 1µA trickle. Small footprint packaging, and the use of
small, low value capacitors ensure board space savings as
well. Data rates greater than 250kbps are guaranteed at
worst case load conditions. This family is fully compatible
with 3.3V-only systems, mixed 3.3V and 5V systems, and
5V-only systems, and is a lower power, pin-for-pin
replacement for ‘207E and ‘237E type devices.
The ICL3217E features an automatic powerdown function
which powers down the on-chip power-supply and driver
circuits. This occurs when an attached peripheral device is
shut off or the RS-232 cable is removed, conserving system
power automatically, without changes to the hardware or
operating system. The ICL3217E powers up again when a
valid RS-232 voltage is applied to any receiver input.
Table 1 summarizes the features of the devices represented
by this data sheet, while application Note AN9863
summarizes the features of each device comprising the
ICL32XXE 3V family.
±15kV Human Body
FN4914.5
Features
• Pb-Free Available as an Option (see Ordering Info)
• ESD Protection for RS-232 I/O Pins to
±15kV (IEC61000)
• 5V Lower Power Replacement for MAX207E, HIN207E,
HIN237E
• Meets EIA/TIA-232 and V.28/V.24 Specifications at 3V
• Latch-Up Free
• On-Chip Voltage Converters Require Only Four External
0.1µF Capacitors
• RS-232 Compatible with V
• Automatic Powerdown (I
= 2.7V
CC
= 1µA, ICL3217E Only)
CC
• Receiver Hysteresis For Improved Noise Immunity
• Guaranteed Minimum Data Rate . . . . . . . . . . . . . 250kbps
• Guaranteed Minimum Slew Rate . . . . . . . . . . . . . . . 6V/µs
• Wide Power Supply Range . . . . . . . Single +3V to +5.5V
Applications
• Battery Powered, Hand-Held, and Portable Equipment
• Laptop Computers, Notebooks, Palmtops
• Modems, Printers and other Peripherals
• ISDN Terminal Adaptors and Set Top Boxes
• Related Literature
- Technical Brief TB363, Guidelines for Handling and
Processing Moisture Sensitive Surface Mount
Devices (SMDs)
Pinout
ICL3207E, ICL3217E (SOIC, SSOP)
T3
OUT
T1
OUT
T2
OUT
R1
IN
R1
OUT
T2
IN
T1
IN
GND
V
CC
C1+
V+
C1-
1
2
3
4
5
6
7
8
9
10
11
12
TOP VIEW
T4
24
OUT
R2
23
IN
R2
22
OUT
T5
21
IN
T5
20
OUT
T4
19
IN
T3
18
IN
R3
17
OUT
R3
16
IN
V-
15
C2-
14
C2+
13
TABLE 1. SUMMARY OF FEATURES
NO. OF MONITOR
NO. OF TXNO. OF
PART NUMBER
ICL3207E 5 3 0 250 NO NO NO
ICL3217E 5 3 0 250 NO NO YES
RX
RX (R
1
) DATA RATE
OUTB
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
(kbps)
RX ENABLE
FUNCTION?
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2000, 2001, 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
MANUAL
POWER-
DOWN?
AUTOMATIC
POWERDOWN
FUNCTION?
ICL3207E, ICL3217E
Ordering Information
(NOTE 1)
PART NO.
ICL3207ECA 0 to 70 24 Ld SSOP M24.209
ICL3207ECAZ
(See Note 2)
ICL3207ECB 0 to 70 24 Ld SOIC M24.3
ICL3207ECBZ
(See Note 2)
ICL3217ECA 0 to 70 24 Ld SSOP M24.209
ICL3217ECAZ
(See Note 2)
ICL3217ECB 0 to 70 24 Ld SOIC M24.3
ICL3217ECBZ
(See Note 2)
ICL3217EIA -40 to 85 24 Ld SSOP M24.209
ICL3217EIAZ
(See Note 2)
ICL3217EIB -40 to 85 24 Ld SOIC M24.3
ICL3217EIBZ
(See Note 2)
NOTES:
1. Most surface mount devices are available on tape and reel; add
“-T” to suffix.
2. Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin
plate termination finish, which is compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
TEMP.
RANGE (°C) PACKAGE
0 to 70 24 Ld SSOP (Pb-Free) M24.209
0 to 70 24 Ld SOIC (Pb-Free) M24.3
0 to 70 24 Ld SSOP (Pb-Free) M24.209
0 to 70 24 Ld SOIC (Pb-Free) M24.3
-40 to 85 24 Ld SSOP (Pb-Free) M24.209
-40 to 85 24 Ld SOIC (Pb-Free) M24.3
PKG.
DWG. #
Pin Descriptions
PIN FUNCTION
V
System power supply input (3.0V to 5.5V).
CC
V+ Internally generated positive transmitter supply (+5.5V).
V- Internally generated negative transmitter supply (-5.5V).
GND Ground connection.
C1+ External capacitor (voltage doubler) is co nnecte d to this l ead.
C1- External capacitor (voltage doubler) is co nnecte d to this l ead.
C2+ External capacitor (voltage inverter) is connected to this lead.
C2- External capacitor (voltage inverter) is connected to this lead.
T
TTL/CMOS compatible transmitter inputs.
IN
T
±15kV ESD Protected, RS-232 level (nominally ±5.5V)
OUT
transmitter outputs.
R
±15kV ESD Protected, RS-232 compatible receiver inputs.
IN
R
TTL/CMOS level receiver outputs.
OUT
2
Typical Operating Circuit
VCC †
TTL/CMOS
LOGIC LEVELS
+
0.1µF
ICL3207E, ICL3217E
ICL32X7E
9
V
CC
T
T
T
T
T
C
1
C2 †
T1
T2
T3
T4
T5
10
C1+
+
†
12
C1-
13
C2+
+
14
C2-
7
IN
6
IN
18
IN
19
IN
21
IN
C3 (OPTIONAL CONNECTION)
+
11
V+
V-
1
2
3
4
5
+
†
C
3
15
C4 †
+
2
T1
OUT
3
T2
OUT
1
T3
24
T4
20
T5
OUT
OUT
OUT
RS-232
LEVELS
† - FOR V
FOR V
R1
R2
R3
= 3.3V, C1 - C4 = 0.1µF or 0.22µF
CC
= 5V, C1 - C4 = 0.1µF OR 1µF
CC
OUT
OUT
OUT
5kΩ
5kΩ
5kΩ
4
R1
IN
23
R2
RS-232
IN
LEVELS
16
R3
IN
5
R
1
22
R
17
2
R
3
GND
8
3
ICL3207E, ICL3217E
Absolute Maximum Ratings Thermal Information
VCC to Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
V+ to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 7V
V- to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.3V to -7V
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14V
Input Voltages
T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 6V
IN
R
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25V
IN
Output Voltages
T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±13.2V
OUT
R
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VCC + 0.3V
OUT
Short Circuit Duration
T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous
OUT
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . See Specification Table
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
3. θ
JA
Thermal Resistance (Typical, Note 3)
θ
(‘/W)
JA
24 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 75
24 Ld SSOP Package . . . . . . . . . . . . . . . . . . . . . . . 100
Maximum Junction Temperature (Plastic Package) . . . . . . . 150°C
Maximum Storage Temperature Range . . . . . . . . . .-65°C to 150°C
Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions
Temperature Range
ICL32X7ECX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
ICL32X7EIX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C
Electrical Specifications Test Conditions: V
Typicals are at T
= 3V to 5.5V, C1 - C4 = 0.1µF; Unless Otherwise Specified.
CC
= 25°C
A
TEMP
PARAMETER TEST CONDITIONS
(°C) MIN TYP MAX UNITS
DC CHARACTERISTICS
Supply Current, Automatic
All R
Open (ICL3217E Only) 25 - 1.0 10 µA
IN
Powerdown
Supply Current,
All Outputs Unloaded 25 - 0.3 1.0 mA
Automatic Powerdown Disabled
TRANSMITTER INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold Low T
Input Logic Threshold High T
Input Leakage Current T
Output Leakage Current
IN
IN
IN
VCC = 3.3V Full 2.0 - - V
V
= 5.0V Full 2.4 - - V
CC
Full - - 0.8 V
Full - ±0.01 ±1.0 µA
Full - ±0.05 ±10 µA
(ICL3217E Only)
Output Voltage Low I
Output Voltage High I
= 1.6mA Full - - 0.4 V
OUT
= -1.0mA Full VCC-0.6 VCC-0.1 - V
OUT
AUTOMATIC POWERDOWN (ICL3217E Only)
Receiver Input Thresholds to
ICL3217E Powers Up (Figure 4) Full -2.7 - 2.7 V
Enable Transmitters
Receiver Input Thresholds to
ICL3217E Powers Down (Figure 4) Full -0.3 - 0.3 V
Disable Transmitters
Receiver Threshold to
Transmitters Enabled Delay (t
Receiver Positive or Negative
WU
)
25 - 100 - µs
25 - 30 - µs
Threshold to Transmitters
Disabled Delay
RECEIVER INPUTS
Input Voltage Range Full -25 - 25 V
Input Threshold Low V
Input Threshold High V
= 3.3V 25 0.6 1.2 - V
CC
= 5.0V 25 0.8 1.5 - V
V
CC
= 3.3V 25 - 1.5 2.4 V
CC
V
= 5.0V 25 - 1.8 2.4 V
CC
4
Loading...