Intersil Corporation HS-201HSRH Datasheet

TM

HS-201HSRH

Data Sheet June 2000

Radiation Hardened High Speed, Quad
SPST, CMOS Analog Switch

The HS-201HSRH is a monolithic CMOS analog switch
featuring power-offhigh input impedance, very fast switching
speeds and low ON resistance. Fabrication on our DI RSG
process assures SEL immunity and only very slight
sensitivity to low dose rate (ELDRS). These Class V/Q
devices are tested and guaranteed for 300krad (Si) total
dose performance.

Power-off high input impedance enables the use of this
device in redundant circuits without causing data bus signal
degradation. ESD protection, overvoltage protection, fast
switching times, low ON resistance, and guaranteed
radiation hardness, make the HS-201HSRH ideal for any
space application where improved switching performance is
required.

Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center (DSCC). The SMD numbers
listed here must be used when ordering flight units.

Detailed electrical specifications for this device are
contained in SMD 5962-99618. A ”hot-link” is provided
on our homepage for downloading.

www.intersil.com/spacedefense/space.asp

Ordering Information

INTERNAL

ORDERING NUMBER

5962F9961801VEC HS1-201HSRH-Q -55 to 125
5962F9961801QEC HS1-201HSRH-8 -55 to 125

MKT. NUMBER

TEMP.

RANGE (oC)

File Number 4874

Features

• Electrically Screened to DSCC SMD 5962-99618

• QML Qualified per MIL-PRF-38535

• Radiation Performance

- Guaranteed Total Dose Performance . . . . . 300krad (Si)

- SEL Immune. . . . . . . . . . . . . . . . . . . . .DI RSG Process

- Only Very Slightly Sensitive to Low Dose Rates
(Vertical PNP and NPN device architectures)

• Overvoltage Protection (Power On, Switch Off). . . . . . . ±30V

• Power Off High Impedance . . . . . . . . . . . . . . . . . . . ±17V

• Fast Switching Times

-t

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110ns (Max)

ON

-t

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80ns (Max)

OFF

• Low “ON” Resistance . . . . . . . . . . . . . . . . . . . 50Ω (Max)

• Pin Compatible with Industry Standard 201 Types

• Operating Supply Range . . . . . . . . . . . . . . . . . ±10V to ±15V

• Wide Analog Voltage Range (±15V Supplies) . . . . . . . ±15V

• TTL Compatible

Applications

• High Speed Multiplexing

• Sample and Hold Circuits

• Digital Filters

• Operational Amplifier Gain Switching Networks

• Integrator Reset Circuits

5962F9961801VXC HS9-201HSRH-Q -55 to 125
5962F9961801QXC HS9-201HSRH-8 -55 to 125
5962F9961801V9A HS0-201HSRH-Q -55 to 125
HS1-201HSRH/PROTO HS1-201HSRH/PROTO -55 to 125

1

1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000

Pinout

HS1-201HSRH, SBDIP (CDIP2-T16)

HS9-201HSRH, FLATPACK (CDFP4-F16)

TOP VIEW

16

1

A1

2

OUT1

3

IN1

4

V-

5

GND

6

IN4

7

OUT4

8

A4

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

A2

15

OUT2

14

IN2

13

V+

12

NC

11

IN3

10

OUT3

9

A3

Die Characteristics

HS-201HSRH

DIE DIMENSIONS

2667µm x 4623µm (105 mils x 182 mils)
Thickness: 483µm ±25.4µm (19 mils ±1 mil)

INTERFACE MATERIALS

Glassivation

Type: Phosphorus Silicon Glass (PSG)
Thickness: 8.0kÅ +/-1.0kÅ

Metallization

Type: Ti/AlCu
Thickness: 16.0kÅ +/- 2kÅ

Substrate

Rad Hard Silicon Gate, Dielectric Isolation

Metallization Mask Layout

OUT4 IN4 GND V- IN1

HS-201HSRH

Backside Finish

Silicon

ASSEMBLY RELATED INFORMATION

Substrate Potential

Unbiased (DI)

ADDITIONAL INFORMATION

Worst Case Current Density

5

2

<2.0 x 10

A/cm

Transistor Count

328

OUT1

A4

A3

OUT3 IN3 V+ IN2 OUT2

A1

A2

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.

Intersil semiconductor products are sold by description only. Intersil Corporation reservesthe right to make changes in circuit design and/or specifications at any time with­out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site www.intersil.com

2