Intersil Corporation HS-0508RH, HS-0509RH Datasheet
HS-0508RH, HS-0509RH
Data Sheet August 1999
Radiation Hardened Single 8/Differential
4-Channel CMOS Analog Multiplexers
These radiation hardened monolithic CMOS multiplexers
each include an array of eight analog switches, a digital
decode circuit for channel selection, a voltage reference for
logic thresholds, and an ENABLE input for device selection
when several multiplexers are present.
The Dielectric Isolation (DI) process used in fabrication of
these devices eliminates the problem of latch-up. Also, DI
offers much lower substrate leakage and parasitic
capacitance than conventional junction-isolated CMOS.
Switches are guaranteed to break-before-make, so that two
channels are never shorted together. The switching
threshold for each digital input is established by an internal
+5V reference, providing a guaranteed minimum 2.4V for
logic “1” and maximum 0.8 for logic “0”. This allows direct
interface without pull-up resistors to signals from most logic
families: CMOS, TTL, DTL and some PMOS. For protection
against transient overvoltage, the digital inputs include a
series 200Ω resistor and a diode clamp to each supply. The
HS-0508RH is an eight channel single-ended multiplexer,
and the HS-0509RH is a four channel differential version. If
input overvoltage protection is needed, the HS-0548RH and
HS-0549RH multiplexers are recommended.
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus(DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-95692. A “hot-link” is provided
on our homepage for downloading.
http://www.intersil.com/spacedefense/space.htm
File Number
3977.2
Features
• Electrically Screened to SMD # 5962-95692
• QML Qualified per MIL-PRF-38535 Requirements
4
• Gamma Dose. . . . . . . . . . . . . . . . . . . . . . 1 x 10
RAD(Si)
• No Latch-Up
• No Channel Interaction During Overvoltage
• Low On Resistance . . . . . . . . . . . . . . . . . . . .<200Ω (Typ)
• 44V Maximum Power Supply
• Break-Before-Make Switch
• Analog Signal Range . . . . . . . . . . . . . . . . . . . . . . . . ±15V
• Access Time. . . . . . . . . . . . . . . . . . . . . . . . . <300ns (Typ)
Applications
• Data Acquisition Systems
• Control Systems
• Telemetry
Ordering Information
INTERNAL
ORDERING NUMBER
5962D9569201VEA HS1-0508RH-Q -55 to 125
5962D9569201VEC HS1B-0508RH-Q -55 to 125
5962D9569202VEA HS1-0509RH-Q -55 to 125
5962D9569202VEC HS1B-0509RH-Q -55 to 125
MKT. NUMBER
TEMP. RANGE
(oC)
Pinouts
HS-0508RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
A0
ENABLE
-VSUPPLY
IN 1
IN 2
IN 3
IN 4
OUT
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
1
A1
A2
GND
+VSUPPLY
IN 5
IN 6
IN 7
9
IN 8
HS-0509RH GDIP1-T16 (CERDIP)
OR CDIP2-T16 (SBDIP)
TOP VIEW
16
1
A0
IN 1A
IN 2A
IN 3A
IN 4A
OUTA
2
3
4
5
6
7
8
| Copyright © Intersil Corporation 1999
ENABLE
-VSUPPLY
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
A1
15
GND
14
+VSUPPLY
13
IN 1B
12
IN 2B
IN 3B
11
10
IN 4B
9
OUT B
Functional Diagrams
HS-0508RH HS-0509RH
HS-0508RH, HS-0509RH
IN1
IN2
IN8
5V
REF
†DIGITAL INPUT
PROTECTION
DECODER/
DRIVER
LEVEL
SHIFT
†
†
†
A0 A1 EN
A2
OUT
†
HS-0508RH TRUTH TABLE
A2 A1 A0 EN “ON” CHANNEL
X X X L NONE
LLLH 1
LLHH 2
LHLH 3
LHHH 4
HLLH 5
HLHH 6
HHLH 7
HHHH 8
IN1A
IN4A
IN1B
IN4B
5V
REF
†DIGITAL INPUT
PROTECTION
DECODER/
DRIVER
LEVEL
SHIFT
†
†
A0 A1
EN
OUT A
OUT B
†
HS-0509RH TRUTH TABLE
A1 A0 EN “ON” CHANNEL PAIR
X X L NONE
LLH 1
LHH 2
HLH 3
HHH 4
2
Loading...