Intersil Corporation HIN14C89E Datasheet

HIN14C89E
PRELIMINARY
Data Sheet January 1999 File Number
Low Power Quad RS-232 Receiver
The HIN14C89E is a high-ESD tolerant, very low power, quad RS-232 receiver interface circuit that is designed to meet EIA/TIA-232, EIA/TIA-562, and CCITT V.28 specifications.
The receivers can handle up to ±25V, and have a 3 to 7k input impedance. The receivers havehysteresis and on-chip noise filtering to improve noise rejection and make external filtering components unnecessary. The outputs are TTL and CMOS compatible and operate at 240Kbps.
Ordering Information
PART
NUMBER
HIN14C89ECP 0 to 70 14 Ld PDIP E14.3 HIN14C89ECBN 0 to +70 14 Ld SOIC M14.15
TEMP. RANGE
(oC) PACKAGE
PKG.
NO.
Pinout
HIN14C89E
(PDIP, SOIC)
TOP VIEW
4647
Features
• Pin-Compatible ESD Upgrade for “1489” Socket
• Meets All RS-232C Specifications
• Enhanced ESD Protection
- ±15KV Human Body Model
- ±15KV IEC1000-4-2, Air-Gap Discharge
- ±8KV IEC1000-4-2, Contact Discharge
• Latch-Up Free During an ESD Event
• Very Low Power Consumption (1µA Typical)
• 240Kbps Data Rate (Typical)
• 4 Receivers per Package
- ±25V Input Voltage Range
- 3 to 7k Input Impedance
- 0.5V Hysteresis to Improve Noise Rejection
• All Critical Parameters are Guaranteed Over the Entire Commercial Temperature Range
- Functionally Interchangeable and Pin Compatible with
MAX1489E, MC1489, MC14C89A, SN75189, SN75C189, DS1489, DS14C89, and DS14C89A
INPUT A
NC
OUTPUT A
INPUT B
NC
OUTPUT B
GND
V
1 2 3 4 5 6 7
14
INPUT D
13
NC
12 11
OUTPUT D
10
INPUT C
9
NC
8
OUTPUT C
CC
Applications
• Computers - Portable and Mainframe
• Peripherals - Printers and Terminals
• Modems
• Dataloggers
468
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207
| Copyright © Intersil Corporation 1999
HIN14C89E
Absolute Maximum Ratings Thermal Information
VCC to Ground. . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) < VCC < 6V
Input Voltages
Input A - D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25V
Output Voltages
Output A - D. . . . . . . . . . . . . (GND -0.3V) < VRXOUT < (V+ +0.3V)
Short Circuit Duration
Output A - D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continuous
Continuous Total Power Dissipation (TA = 25oC)
Plastic Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .375mW
Derate -7.0 mW/C above 70oC ESD Classification: EIC1000-4-2 Class 4 Compliant
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Thermal Resistance (Typical, Note 1) θJA (oC/W)
14 Ld PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . 90
14 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . 120
Maximum Junction Temperature (Plastic Package) . . . . . . . .150oC
Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300oC
Temperature Ranges
HIN14C89EC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC
Electrical Specifications Test Conditions: V
= +5V ±10%, TA = Operating Temperature Range
CC
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
Output Voltage High, V Output Voltage Low, V Output Short Circuit Current, I
OH
OL
OS
(Note 2) Supply Current, I
Input Voltage Range, V Input Voltage High, V Input Voltage Low, V Input Hysteresis, V Input Resistance, R
CC
lN
lH
lL
HYST
lN
Output Propagation Delay, Low to High, t Output Propagation Delay, High to Low, t Output Propagation Delay Skew, [t
t
SKEW
Output Transition Time, t Input Noise Rejection, t
TR
N
PLH
+ t
PLH PHL
PHL
I
= -3.2mA 2.5 4.1 - V
OUT
I
= 3.2mA - 0.17 0.4 V
OUT
Shorted to GND - -11 ­Shorted to V
CC
-35-
- 1 100 µA
-25 - 25 V
- 2.15 2.60 V
0.75 1.4 - V
- 0.7 - V
3.0 5.0 7.0 k
- 1.9 4.0 µS
- 2.0 4.0 µS
],
V
= 10% to 90% - 110 - nS
OUT
- 120 - nS
Pulse Amplitude = 5V - 0.8 - µS
mA
Guaranteed Data Rate, DR VCC = 5V 120 240 - kbps ESD Protection Human Body Model (Note 3)
IEC1000-4-2 (Contact Discharge) IEC1000-4-2 (Air-Gap Discharge)
- ±15
±8
±15
-
NOTES:
2. Guaranteed by design.
3. RlNpins to GND.
kV
469
Loading...
+ 2 hidden pages