Intersil Corporation HFA1145-883 Datasheet

June 1994

HFA1145/883

High Speed, Low Power, Current Feedback Video

Operational Amplifier with Output Disable

Features

• This Circuit is Processed in Accordance to MIL-STD­883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.

• Low Supply Current. . . . . . . . . . . . . . . . . . 5.9mA (Typ)

• Wide -3dB Bandwidth . . . . . . . . . . . . . . . 360MHz (Typ)

• High Slew Rate. . . . . . . . . . . . . . . . . . . . 1000V/µs (Typ)

• Excellent Gain Flatness (to 50MHz) . . . . .±0.07dB (Typ)

• Excellent Differential Gain . . . . . . . . . . . . . 0.02% (Typ)

• Excellent Differential Phase . . . . . . . . . 0.03 Deg. (Typ)

• High Output Current . . . . . . . . . . . . . . . . . . 60mA (Typ)

• Output Enable / Disable Time. . . . . . 180ns/35ns (Typ)

Applications

• Multiplexed Flash A/D Driver

• RGB Multiplexers / Preamps for Multimedia Systems

• Video Switching and Routing

• Pulse and Video Amplifiers

• Wideband Amplifiers

Description

The HFA1145/883 is a high speed, low power current
feedback amplifier built with Intersil’ proprietary
complementary bipolar UHF-1 process.

This amplifier features a TTL/CMOS compatible disable
control, pin 8, which when pulled low, reduces the supply
current and forces the output into a high impedance state.
This allows easy implementation of simple, low power video
switching and routing systems. Component and composite
video systems also benefit from this op amp’s excellent gain
flatness, and good differential gain and phase specifications.

Multiplexed A/D applications will also find the HFA1145/883
useful as the A/D driver/multiplexer.

The HFA1145/883 is a low power , high performance upgrade
for the CLC410.

Ordering Information

TEMPERATURE

PART NUMBER

HFA1145MJ/883 -55oC to +125oC 8 Lead CerDIP

RANGE PACKAGE

• RF/IF Signal Processing

• Medical Imaging Systems

Pinout

NC

-IN

+IN

V-

HFA1145/883

(CERDIP)

TOP VIEW

1
2

-

+

3
4

8

DISABLE

7

V+

6

OUT

5

NC

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207

| Copyright © Intersil Corporation 1999

3-214

Spec Number 511116-883

File Number 3726

Specifications HFA1145/883

Absolute Maximum Ratings Thermal Information

Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V

Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to V-

Output Current (Note 1) . . . . . . . . . . . . . . . . Short Circuit Protected

Output Current (50% Duty Cycle, Note 1) . . . . . . . . . . . . . . . .60mA

Junction Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC

ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .> 2000V

Storage Temperature Range . . . . . . . . . . . . . .-65oC ≤ TA≤ +150oC

Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

Operating Conditions

Operating V

Operating Temperature Range. . . . . . . . . . . . .-55oC ≤ TA≤ +125oC

Device Tested at: V

PARAMETERS SYMBOL CONDITIONS

Input Offset Voltage V

Common Mode
Rejection Ratio

Power Supply
Rejection Ratio

Non-Inverting Input (+IN)
Current

+IN Current Common
Mode Sensitivity

+IN Resistance +R

(±VS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±5V

SUPPLY

TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS

= ±5V, AV= +1, RF= 510Ω, R

SUPPLY

VCM= 0V 1 +25oC-55mV

IO

CMRR ∆VCM= ±1.8V

V+ = 3.2V, V- = -6.8V
V+ = 6.8V, V- = -3.2V

∆VCM= ±1.2V
V+ = 3.8V, V- = -6.2V
V+ = 6.2V, V- = -3.8V

PSRRP ∆V

SUPPLY

V+ = 6.8V, V- = -5V
V+ = 3.2V, V- = -5V

∆V

SUPPLY

V+ = 6.2V, V- = -5V
V+ = 3.8V, V- = -5V

PSRRN ∆V

SUPPLY

V+ = 5V, V- = -6.8V
V+ = 5V, V- = -3.2V

∆V

SUPPLY

V+ = 5V, V- = -6.2V
V+ = 5V, V- = -3.8V

I

BSP

CMS

VCM= 0V 1 +25oC -15 15 µA

∆VCM= ±1.8V

IBP

V+ = 3.2V, V- = -6.8V
V+ = 6.8V, V- = -3.2V

∆VCM= ±1.2V
V+ = 3.8V, V- = -6.2V
V+ = 6.2V, V- = -3.8V

Note 2 1 +25oC 800 - kΩ

IN

SOURCE

= ±1.8V

= ±1.2V

= ±1.8V

= ±1.2V

Thermal Resistance θ

CerDIP Package . . . . . . . . . . . . . . . . . 115oC/W 30oC/W

Maximum Package Power Dissipation at +75oC

CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.87W

Package Power Dissipation Derating Factor above +75oC

CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.7mW/oC

RL ≥ 50Ω

= 0Ω, RL = 100Ω, V

=0V,DIS = Floated, Unless Otherwise Specified.

OUT

GROUP A

SUBGROUPS TEMPERATURE

2, 3 +125oC, -55oC -10 10 mV

1 +25oC47-dB
2 +125oC44-dB

3 -55oC44-dB

1 +25oC50-dB
2 +125oC46-dB

3 -55oC46-dB

1 +25oC50-dB
2 +125oC46-dB

3 -55oC46-dB

2, 3 +125oC, -55oC -25 25 µA

1 +25oC - 1.25 µA/V
2 +125oC - 2.85 µA/V

3 -55oC - 2.85 µA/V

2, 3 +125oC, -55oC 350 - kΩ

JA

LIMITS

θ

JC

UNITSMIN MAX

3-215

Spec Number 511116-883