Intersil Corporation HC55184, HC55183, HC55182, HC55181, HC55180 Datasheet

HC55180, HC55181, HC55182, HC55183, HC55184

Data Sheet October 1998 File Number 4519.4

Extended Reach Ringing SLIC Family

The RSLIC18 family of
ringing subscriber line
interface circuits (RSLIC)
supports analog Plain Old

TelephoneService (POTS) in
short and medium loop length, wireless and wireline
applications. Ideally suited for remote subscriber units, this
family of products offers flexibility to designers with high
ringing voltage and low power consumption system
requirements.

The RSLIC18 family operates to 100V which translates
directly to the amount of ringing voltage supplied to the end
subscriber. With the high operating voltage, subscriber loop
lengths can be extended to 500Ω (i.e., 5,000 feet) and
beyond.

Other key features across the product family include: low
power consumption, ringing using sinusoidal or trapezoidal
waveforms, robust auto-detection mechanisms for when
subscribers go on or off hook, and minimal external discrete
application components. Integrated test access features are
also offered on selected products to support loopback
testing as well as line measurement tests.

There are five product offerings in the RSLIC18 family:
HC55180, HC55181, HC55182, HC55183 and HC55184.
The architecture for this family is based on a voltage feed
amplifier design using low fixed loop gains to achieve high
analog performance with low susceptibility to system
induced noise.

Block Diagram

POL CDC VBHVBL

RINGING

PORT

VRS

ILIM

DC

CONTROL

BATTERY

SWITCH

Features

• Battery Operation to 100V

• Low Standby Power Consumption of 50mW

• Peak Ringing Amplitude 95V, 5 REN

• Sinusoidal or Trapezoidal Ringing Capability

• Integrated CODEC Ringing Interface

• Integrated MTU DC Characteristics

• Low External Component Count

• Pulse Metering and On Hook Transmission

• Tip Open Ground Start Operation

• Thermal Shutdown with Alarm Indicator

• 28 Lead Surface Mount Packaging

• Dielectric Isolated (DI) High Voltage Design

• HC55180

- Silent Polarity Reversal

- 53dB Longitudinal Balance

- Loopback Test Capability

• HC55181

- Integrated Battery Switch

- Silent Polarity Reversal

- 58/53dB Longitudinal Balance

- Loopback and Test Access Capability

• HC55182

- Integrated Battery Switch

- 58/53dB Longitudinal Balance

- Loopback and Test Access Capability

• HC55183

- Integrated Battery Switch

- 45dB Longitudinal Balance

• HC55184

- Integrated Battery Switch

- Silent Polarity Reversal

- 45dB Longitudinal Balance

Applications

TIP

RING

SW+

SW-

2-WIRE

PORT

TEST

ACCESS

TRANSMIT

DETECTOR

RTD RD

SENSING

LOGIC

E0

28

DET ALM

• Wireless Local Loop (WLL)

• Digital Added Main Line (DAML)/Pairgain

• Integrated Services Digital Network (ISDN)

• Small Office Home Office (SOHO) PBX

4-WIRE

PORT

VRX
VTX

-IN
VFB

• Cable/Computer Telephony

CONTROL

LOGIC

BSEL

F2
F1
F0

SWC

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

Related Literature

• AN9814, User’s Guide for Development Board

• AN9824, Modeling of the AC Loop

• AN TBD, Interfacing to DSP CODECs

RSLIC18™ is a trademark of Intersil Corporation.

http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999

HC55180, HC55181, HC55182, HC55183, HC55184

Ordering Information (PLCC Package Only)

LOOP

BATSWPOL

PART NUMBER 100V 85V

REV

FULL
TEST

BACK
ONLY LB = 53dB LB = 58dB

TEMP.

RANGEoC PACKAGE

PACKAGE

NO.

HC55180CIM
HC55180DIM
HC55181AIM
HC55181BIM
HC55181CIM
HC55181DIM
HC55182AIM
HC55182BIM
HC55182CIM
HC55182DIM
HC55183ECM 75V
HC55184ECM 75V
HC5518XEVAL1 Evaluation board platform, including CODEC.

••••

•• ••

•••• •

••• • •

•••• •

••• • •

•• • •

•• • •

•• • •

•• • •

•

••

Device Operating Modes

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45

-40 to 85 28 Ld PLCC N28.45
45dB 0 to 70 28 Ld PLCC N28.45
45dB 0 to 70 28 Ld PLCC N28.45

OPERATING

MODE F2 F1 F0 E0 = 1 E0 = 0 DESCRIPTION HC55180 HC55181 HC55182 HC55183 HC55184

Low Power
Standby

Forward Active 0 0 1 SHD GKD Forward battery loop feed.
Unused 0 1 0 n/a n/a This is a reserved internal

Reverse Active 0 1 1 SHD GKD Reverse battery loop feed.
Ringing 1 0 0 RTD RTD Balanced ringing mode

Forward Loop
Back

Tip Open 1 1 0 SHD GKD Tip amplifier disabled and

Power Denial 1 1 1 n/a n/a Device shutdown.

0 0 0 SHD GKD MTU compliant standby

mode with active loop
detector.

test mode.

supporting both sinusoidal,
trapezoidal and ringing
waveforms with DC offset.

1 0 1 SHD GKD Internal device test mode.

ring amplifier enabled.
Intended for PBX type
applications.

•••••

•••••

•• •

•••••

•••

•••

•••••

29

Pinouts

HC55180, HC55181, HC55182, HC55183, HC55184

HC55180

(PLCC)

TOP VIEW

RD

RING

NC

17

27

POL

ILIM

26

RTD

25

CDC

24

VCC

23
22

-IN
VFB

21

VTX

20

VRX

19

18

VRS

NC
NC
NC

F2
F1
F0
E0

TIP

VBL

VBH

13

3

ALM

14

BGND

15

AGND

12

28

16

NC

4

5
6
7

8

9
10
11

12

DET

SW+

SW-

SWC

F2
F1
F0
E0

NC
NC
NC

F2
F1
F0
E0

HC55181

(PLCC)

TOP VIEW

RD

RING

NC

17

27

POL

ILIM

26

RTD

25

CDC

24

VCC

23
22

-IN
VFB

21

VTX

20

VRX

19

18

VRS

SW+

SW-

SWC

F2
F1
F0
E0

5
6
7

8

9
10
11

TIP

VBL

VBH

13

3

ALM

14

BGND

15

AGND

12

BSEL

28

16

4

5
6
7

8

9
10
11

12

DET

HC55183

(PLCC)

TOP VIEW

RD

RING

NC

ILIM

27

26

RTD

25

CDC

24

VCC

23
22

-IN
VFB

21

VTX

20

VRX

19

17

18

NC

VRS

NC
NC
NC

F2
F1
F0
E0

4

5
6
7

8

9
10
11

12

DET

14

BGND

15

AGND

TIP

12

16

BSEL

28

VBL

VBH

4

3

5
6
7

8

9
10
11

12

13

DET

ALM

12

VBH

VBH

4

DET

3

13

ALM

HC55182

(PLCC)

TOP VIEW

VBL

3

13

14

ALM

HC55184

(PLCC)

TOP VIEW

BGND

VBL

14

AGND

BGND

15

AGND

TIP

12

15

BSEL

TIP

12

BSEL

28

16

RING

28

16

NC

RING

27

17

NC

27

17

RD

POL

RD

NC

26

18

26

18

ILIM

25
24
23
22
21
20
19

VRS

ILIM

25
24
23
22
21
20
19

VRS

RTD
CDC
VCC

-IN
VFB

VTX
VRX

RTD
CDC
VCC

-IN
VFB

VTX
VRX

30

HC55180, HC55181, HC55182, HC55183, HC55184

Absolute Maximum Ratings T

Maximum Supply Voltages

VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +7V

VCC - V
VCC - V

Uncommitted Switch Voltage . . . . . . . . . . . . . . . . . . . . . . . -110V

ESD (Human Body Model). . . . . . . . . . . . . . . . . . . . . . . . . . . . 500V

(180, 181, 182) . . . . . . . . . . . . . . . . . . . . . . . . . 110V

BAT

(183, 184) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85V

BAT

=25oC Thermal Information

A

Thermal Resistance (Typical, Note 1) θJA(oC/W)

PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Maximum Junction Temperature Plastic . . . . . . . . . . . . . . . . 150oC

Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(PLCC - Lead Tips Only)

Operating Conditions

Temperature Range

Industrial (I suffix). . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC

Commercial (C suffix). . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC

Positive Power Supply (VCC). . . . . . . . . . . . . . . . . . . . . . . +5V ±5%

Negative Power Supply (VBH, VBL) (180, 181, 182) . -16V to -100V

Negative Power Supply (VBH, VBL) (183, 184) . . . . . . -24V to -75V

Uncommitted Switch (loop back or relay driver). . . . . . +5V to -100V

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationofthe
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE:

1. θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications Unless Otherwise Specified, T

VBH= -100V, -85V or -75V, VCC = +5V, AGND = BGND = 0V, loop current limit = 25mA. All AC Parameters are
specified at 600Ω 2-wire terminating impedance over the frequency band of 300Hz to 3.4kHz. Protection
resistors = 0Ω. These parameters apply generically to each product offering.

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

RINGING PARAMETERS (Note 2)

VRS Input Impedance (Note 3) 480 - - kΩ
Differential Ringing Gain VRS to 2-wire, R
4-Wire to 2-Wire Ringing Off Isolation Active mode, referenced to VRS input. - 60 - dB
2-Wire to 4-Wire Transmit Isolation Ringing mode referenced to the differential ringing

AC TRANSMISSION PARAMETERS (Notes 5, 6)
Receive Input Impedance (Note 3) 160 - - kΩ
Transmit Output Impedance (Note 3) --1Ω
4-Wire Port Overload Level THD = 1% 3.1 3.5 - V
2-Wire Port Overload Level THD = 1% 3.1 3.5 - V
2-Wire Return Loss 300Hz ≤ f < 1kHz 30 45 - dB

Longitudinal Current Capability (Per Wire) (Note 3) Test for False Detect 20 - - mA

4-Wire to 2-Wire Insertion Loss -0.20 0.0 +0.30 dB
2-Wire to 4-Wire Insertion Loss -6.22 -6.02 -5.82 dB
4-Wire to 4-Wire Insertion Loss -6.22 -6.02 -5.82 dB
Idle Channel Noise 2-Wire C-Message - 16 19 dBrnC

Idle Channel Noise 4-Wire C-Message - 10 13 dBrnC

DC PARAMETERS (Note 6)
Loop Current Limit Programming Range (Note 5) Max Low Battery = -52V 15 - 45 mA
Loop Current During Low Power Standby Forward polarity only. 18 - 26 mA

= 0oC to 70oC for the HC55183, 184 only, all others -40oC to 85oC, VBL = -24V,

A

amplitude.

1kHz ≤ f ≤ 3.4kHz 35 45 - dB

Test for False Detect, Low Power Standby 10 - - mA

Psophometric - -73.5 -71 dBmp

Psophometric - -79.5 -77 dBmp

Die Characteristics

Substrate Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bipolar-DI

= ∞ (Note 4) 78 80 82 V/V

LOAD

-60- dB

BAT

PK
PK

RMS
RMS

31

HC55180, HC55181, HC55182, HC55183, HC55184

Electrical Specifications Unless Otherwise Specified, T

VBH= -100V, -85V or -75V, VCC = +5V, AGND = BGND = 0V, loop current limit = 25mA. All AC Parameters are
specified at 600Ω 2-wire terminating impedance over the frequency band of 300Hz to 3.4kHz. Protection
resistors = 0Ω. These parameters apply generically to each product offering. (Continued)

PARAMETER TEST CONDITIONS MIN TYP MAX UNITS

LOOP DETECTORS AND SUPERVISORY FUNCTIONS

Switch Hook Programming Range 5 - 15 mA
Switch Hook Programming Accuracy Assumes 1% external programming resistor - 2 10 %
Dial Pulse Distortion --1%
Ring Trip Comparator Threshold 2.3 2.6 2.9 V
Ring Trip Programming Current Accuracy - - 10 %
Ground Key Threshold 10 12 13.5 mA
Thermal Alarm Output IC junction temperature - 175 -

LOGIC INPUTS (F0, F1, F2, E0, SWC)

Input Low Voltage - - 0.8 V
Input High Voltage 2.0 - - V
Input Low Current VIL = 0.4V -20 - - µA
Input High Current VIH = 2.4V - - 5 µA

LOGIC OUTPUTS (DET, ALM)

Output Low Voltage IOL = 5mA - - 0.4 V
Output High Voltage IOH = 100 µA 2.4 - - V

POWER SUPPLY REJECTION RATIO

VCC to 2-Wire f = 300Hz - 40 - dB

VCC to 4-Wire f = 300Hz - 45 - dB

VBL to 2-Wire 300Hz ≤ f ≤ 3.4kHz - 30 - dB
VBL to 4-Wire 300Hz ≤ f ≤ 3.4kHz - 35 - dB
VBH to 2-Wire 300Hz ≤ f ≤ 3.4kHz - 33 - dB
VBH to 4-Wire 300Hz ≤ f ≤ 1kHz - 40 - dB

= 0oC to 70oC for the HC55183, 184 only, all others -40oC to 85oC, VBL = -24V,

A

o

f = 1kHz - 35 - dB
f = 3.4kHz - 28 - dB

f = 1kHz - 43 - dB
f = 3.4kHz - 33 - dB

1kHz < f ≤ 3.4kHz - 45 - dB

C

NOTES:

2. These parameters are specified at high battery operation. For the HC55180 the external supply is set to high battery voltage, for the HC55181,
HC55182, HC55183 and HC55184, BSEL = 1.

3. These parameters are controlled via design or process parameters and are not directly tested. These parameters are characterized upon initial
design release and upon design changes which would affect these characteristics.

4. Differential Ringing Gain is measured with VRS = 0.795 V
for -75V devices.

5. These parameters are specified at low battery operation. For the HC55180, the external supply is set to low battery voltage, for the HC55181,
HC55182, HC55183 and HC55184, BSEL = 0.

6. Forward Active and Reverse Active performance is guaranteed for the HC55180, HC55181 and HC55184 devices only. The HC55182 and
HC55183 are specified for Forward Active operation only.

for -100V devices, VRS = 0.663 V

RMS

for -85V devices and VRS = 0.575 V

RMS

32

RMS

Electrical Specifications Unless Otherwise Specified, T

loop current limit = 25mA. All AC Parameters are specified at 600W 2-wire terminating impedance over the frequency band of 300Hz to 3.4kHz.
Protection resistors = 0W.

HC55180 (Note 7) HC55181, HC55182 HC55183, HC55184

PARAMETER

RINGING PARAMETERS (Note 2)

Ringing Voltage
Open Circuit
(Note 8)

33

Ringing Voltage
Load = 1.3K
(Notes 8, 10)

Tip Centering Voltage VB = -85V, RL = ∞ - 2.5 - VBH = -85V, RL = ∞ - - 2.5 VBH = -75V, RL = ∞ -- 3V

Ring Centering Voltage VB = -85V, RL = ∞ - 2.5 - VBH = -85V, RL = ∞ - - 2.5 VBH = -75V, RL = ∞ -- 3V

AC TRANSMISSION PARAMETERS (Notes 5, 6)
2-Wire Longitudinal Balance

(Notes 12, 13)
4-Wire Longitudinal Balance (Note 11) - - - Grade A, B - 67 - Grade E - 58 - dB

2-Wire to 4-Wire Level Linearity
4-Wire to 2-Wire Level
Linearity
Referenced to -10dBm

DC PARAMETERS

Loop Current Accuracy
(Notes 5, 6)

Open Circuit Voltage
(|Tip - Ring|, Note 6)

Low Power Standby
Open Circuit Voltage
(Tip - Ring, Note 2)

TEST ACCESS FUNCTIONS

Switch On Voltage (Note 14) - - - IOL = 45mA - 0.30 0.60 (Note 14) - - - V
Loopback Max Battery - - 52 - - 52 (Note 15) - - 52 V

THD ≤ 0.5%
VB = -85V

THD ≤ 0.5%
VB = -100V

THD ≤ 2.5%
VB = -85V

THD ≤ 2.0%
VB = -100V

VB = -100V, RL = ∞ - 2.0 - VBH = -100V, RL = ∞ - - 2.0 (Note 9) - - - V

VB = -100V, RL = ∞ - 2.0 - VBH = -100V, RL = ∞ - - 2.0 (Note 9) - - - V

(Note 11) - - - Grade A, B 58 62 - Grade E 45 53 - dB
Grade C, D - 59 - Grade C, D 53 59 - (Note 11) - - - dB

Grade C, D - 64 - Grade C, D - 64 - (Note 11) - - - dB
+3 to -40dBm, 1kHz - 0.025 - +3 to -40dBm, 1kHz - 0.025 - +3 to -40dBm, 1kHz - 0.025 - dB

-40 to -50dBm, 1kHz - 0.050 - -40 to -50dBm, 1kHz - 0.050 - -40 to -50dBm, 1kHz - 0.050 - dB

-50 to -55dBm, 1kHz - 0.100 - -50 to -55dBm, 1kHz - 0.100 - -50 to -55dBm, 1kHz - 0.100 - dB

IL = 25mA - 7 - IL = 25mA - - 7 IL = 25mA - - 10 %

VB = -16V - 7.5 - VBL = -16V 6.5 7.5 9.5 VBL = -16V - 7.5 - V
VB = -24V 14 15.5 17 VBL = -24V 14 15.5 17 VBL = -24V 14 15.5 17 V
VB = -85V - 50 - BSEL = 1, VBH = -85V - 50 - BSEL = 1, VBH = -75V - 50 - V
VB = -100V - 50 - BSEL = 1, VBH= -100V - 50 - (Note 9) - - - V
VB = -48V 43 45 47 VBH = -48V 43 45 47 VBH = -48V 43 45 47 V
VB = -85V 46 49 52 VBH = -85V 46 49 52 VBH = -75V 46 49 52 V
VB = -100V 46 49 52 VBH = -100V 46 49 52 (Note 9) - - - V

= 0oC to 70oC for the HC55183, 184 only, all others -40oC to 85oC, VBL = -24V, VCC = +5V, AGND = BGND = 0V,

A

-80-THD≤ 0.5%
VBH = -85V

-95-THD≤ 0.5%
VBH = -100V

-80-THD≤ 2.5%
VBH = -85V

-95-THD≤ 2.0%
VBH = -100V

80 - - THD ≤ 0.5%

VBH = -75V

95 - - (Note 9) - - - V

80 - - THD ≤ 3.0%

VBH = -75V

95 - - (Note 9) - - - V

70 - - V

70 - - V

UNITSTEST CONDITIONS MIN TYP MAX TEST CONDITIONS MIN TYP MAX TEST CONDITIONS MIN TYP MAX

PEAK

PEAK

HC55180, HC55181, HC55182, HC55183, HC55184

PEAK

PEAK