How it Works
Intersil Corporation
Loading...
HC55130
Datasheet
35 pgs392.06 Kb0

Intersil Corporation HC55151, HC55150, HC55143, HC55142, HC55141 Datasheet

...
HC55120, HC55121, HC55130, HC55131, HC55140,
TM
HC55141, HC55142, HC55143, HC55150, HC55151
Data Sheet June 2000
Low Power Universal SLIC Family
The UniSLIC14 family achieves its ultra low power operation through: Its automatic single and dual battery selection (based on line length) and battery tracking anti clipping to ensure the maximum loop coverage on the lowest battery voltage. This architecture is ideal for power critical applications such as ISDN NT1+, Pairgain and Wireless local loop products.
The UniSLIC14 family has many user programmable features. This family of SLICs delivers a low noise, low component count solution for Central Office and Loop Carrier universal voice grade designs. The product family integrates advanced pulse metering, test and signaling capabilities, and zero crossing ring control.
The UniSLIC14 family is designed in the Intersil “Latch” free Bonded Wafer process. This process dielectrically isolates the active circuitry toeliminate anyleakage paths as foundin our competition’s JI process. This makes the UniSLIC14 family compliant with “hot plug” requirements and operation in harsh outdoor environments.
Block Diagram
RRLY
TRLY1 TRLY2
DT
DR
TIP
RING
BGND
AGND
V
BH
V
BL
V
CC
RING AND TEST
RELAY DRIVERS
ZERO CURRENT
CROSSING
RING TRIP
DETECTOR
POLARITY REVERSAL
2-WIRE
INTERFACE
BATTERY
SELECTION
AND
BIAS
NETWORK
STATE
DECODER
AND
DETECTOR
LOGIC
LOOP CURRENT
DETECTOR
GKD/LOOP LENGTH
DETECTOR
LINE FEED
CONTROL
4-WIRE INTERFACE
VF SIGNAL PATH
PULSE METERING
SIGNAL PATH
SPM
C1 C2
C3 C4
C5 SHD
GKD_LVM
CRT_REV_LVM
ILIM RSYNC_REV ROH CDC RDC_RAC RD
V
TX
V
RX
PTG ZT C
H
File Number 4659.5
Features
• Ultra Low Active Power (OHT) < 60mW
• Single/Dual Battery Operation
• Automatic Silent Battery Selection
• Power Management/Shutdown
• Battery Tracking Anti Clipping
• Single 5V Supply with 3V Compatible Logic
• Zero Crossing Ring Control
- Zero Voltage On/Zero Current Off
• Tip/Ring Disconnect
• Pulse Metering Capability
• 4 Wire Loopback
• Programmable Current Feed
• Programmable Resistive Feed
• Programmable Loop Detect Threshold
• Programmable On-Hook and Off-Hook Overheads
• Programmable Overhead for Pulse Metering
• Programmable Polarity Reversal Time
• Selectable Transmit Gain 0dB/-6dB
• 2 Wire Impedance Set by Single Network
• Loop and Ground Key Detectors
• On-Hook Transmission
• Common Pinout
• HC55121
- Polarity Reversal
• HC55130
- -63dB Longitudinal Balance
• HC55140
- Polarity Reversal
- Ground Start
- Line Voltage Measurement
- 2 Wire Loopback
- -63dB Longitudinal Balance
• HC55142
- Polarity Reversal
- Ground Start
- Line Voltage Measurement
- 2.2V
Pulse Metering
RMS
- 2 Wire Loopback
• HC55150
- Polarity Reversal
- Line Voltage Measurement
- 2.2V
Pulse Metering
RMS
- 2 Wire Loopback
Applications
• Related Literature
- AN9871, User’s Guide for UniSLIC14 Eval Board
4-1
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Ordering Information
MAX
PART
NUMBER
HC55120CB 30
HC55120CM 30
HC55121IB 30
HC55121IM 30
HC55130IB 45 63dB -40 to85M28.3
HC55130IM 45 63dB -40 to85N28.45
HC55131IM 45
HC55140IB 45
HC55140IM 45
HC55141IM 45
HC55142IB 45
HC55142IM 45
HC55143IM 45
HC55150CB 45
HC55150CM 45
HC55151CM 45
HC5514XEVAL1 Evaluation board
LOOP
CURRENT
(mA)
POLARITY
REVERSAL
GND
START
GND KEY
•
•
•• • •
•• • •
••• • •
••• • •
••• • ••
••• • • •
••• • • •
••• • •••
••••
••••
•••••
LINE
VOLTAGE
MEASUREMENT
†
PULSE
METERING
2 TEST RELAY
DRIVERS
† Available by placing SLIC in Test mode.
2 WIRE
LOOP-
BACK
LONGITUDINAL
†
•
BALANCE
53dB 0 to 70 M28.3
53dB 0 to 70 N28.45
53dB -40 to85M28.3
53dB -40 to85N28.45
63dB -40 to85N32.45x55
63dB -40 to85M28.3
63dB -40 to85N28.45
63dB -40 to85N32.45x55
63dB -40 to85M28.3
63dB -40 to85N28.45
63dB -40 to85N32.45x55
55dB 0 to 70 M28.3
55dB 0 to 70 N28.45
55dB 0 to 70 N32.45x55
TEMP
RANGE
o
C)
(
PKG.
NO.
SOIC
PLCC
SOIC
PLCC
SOIC
PLCC
PLCC
SOIC
PLCC
PLCC
SOIC
PLCC
PLCC
SOIC
PLCC
PLCC
Device Operating Modes
C3 C2 C1 DESCRIPTION HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
0 0 0 Open Circuit
4-Wire Loopback
0 0 1 Ringing 0 1 0 Forward Active 0 1 1 Test Forward Active
2 Wire Loopback and Line Voltage Measurement
1 0 0 Tip Open Ground Start 1 0 1 Reserved 1 1 0 Reverse Active 1 1 1 Test Reverse Active
Line Voltage Measurement
4-2
••••••
••••••
••••••
• •••
••
••••••
• •••
•••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Absolute Maximum Ratings T
Temperature, Humidity
Storage Temperature Range . . . . . . . . . . . . . . . . -65oC to 150oC
Operating Temperature Range. . . . . . . . . . . . . . . -40oC to 110oC
Operating Junction Temperature Range. . . . . . . . -40oC to 150oC
Power Supply (-40oC ≤ TA≤ 85oC)
Supply Voltage VCC to GND . . . . . . . . . . . . . . . . . . . .-0.4V to 7V
Supply Voltage VBLto GND. . . . . . . . . . . . . . . . . . . .-VBHto 0.4V
Supply Voltage VBH to GND, Continuous. . . . . . . . . .-75V to 0.4V
Supply Voltage VBH to GND, 10ms . . . . . . . . . . . . . .-80V to 0.4V
Relay Driver
=25oC Thermal Information
A
Thermal Resistance (Typical, Note 1) θ
28 Lead PLCC Package. . . . . . . . . . . . . . . . . . . . . . 52oC/W
28 Lead SOIC Package . . . . . . . . . . . . . . . . . . . . . . 45oC/W
32 Lead PLCC Package. . . . . . . . . . . . . . . . . . . . . . 66.2oC/W
Continuous Power Dissipation at 85oC
28 Lead PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5W
28 Lead SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.0W
32 Lead PLCC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.4W
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . . . . . 300oC
(PLCC, SOIC - Lead Tips Only) Derate above 70oC
JA
Ring Relay Supply Voltage . . . . . . . . . . . . . . . . . . . . . .0V to 14V
Ring Relay Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Digital Inputs, Outputs (C1, C2, C3, C4, C5, SHD, GKD_LVM)
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.4V to V
Output Voltage (SHD, GKD_LVM Not Active). . . . . . -0.4V to V
CC CC
Output Current (SHD,GKD_LVM) . . . . . . . . . . . . . . . . . . . . . 5mA
ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500V
Gate Count. . . . . . . . . . . . . . . . . . . . . . . .543 Transistors, 51 Diodes
Tip and Ring Terminals
Tipx or Ringx, Current, Pulse < 10ms, T Tipx or Ringx, Current, Pulse < 1ms, T Tipx or Ringx, Current, Pulse < 10µs, T Tipx or Ringx, Current, Pulse < 1µs, T Tipx or Ringx, Pulse < 250ns, T
REP
> 10s . . . . . . . . . .2A
REP
> 10s . . . . . . . . . . .5A
REP
> 10s . . . . . . . . .15A
REP
> 10s . . . . . . . . . .20A
REP
> 10s 20A
Tipx and Ringx Terminals (-40oC ≤ TA ≤ 85oC)
Tipx or Ringx Current. . . . . . . . . . . . . . . . . . . . -100mA to 100mA
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on an evaluation PC board in free air.
Typical Operating Conditions
These represent the conditions under which the device was developed and are suggested as guidelines.
PARAMETER CONDITIONS MIN TYP MAX UNITS
Ambient Temperature HC55120, HC55150/1 0 - 70
HC55121, HC55130/1, HC55140/1,
-40 - 85
HC55142/3
o
C
o
C
VBH with Respect to GND -58 - -8 V VBL with Respect to GND V
BH
-0 V
VCC with Respect to GND 4.75 - 5.25 V
4-3
Electrical Specifications T
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
R
= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C
OH
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
to the part. (NA) symbol used to indicate the test does not apply to the part.
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
2-WIRE PORT
Overload Level, Off Hook Forward and Reverse
Overload Level, On Hook Forward and Reverse
4-4
Input Impedance (Into Tip and Ring) - ZT/200 - Ω Longitudinal Impedance (Tip, Ring)
1% THD, I
DCMET
≥ 18mA
3.2 - - V
(Note 2, Figure 1) 1% THD, IDCMET ≤ 5mA
1.3 - - V
(Note 3, Figure 1)
0 < f < 100Hz (Note 4, Figure 2) - 0 - Ω/Wire Forward
Forward and Reverse
LONGITUDINAL CURRENT LIMIT (TIP, RING)
On-Hook, Off-Hook (Active), RL = 736Ω Forward and Reverse
No False Detections, (Loop Current), LB > 45dB (Notes 5, 6, Figures 3A, 3B)
28 - - mA
PEAK
PEAK
Wire Forward
/
RMS
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
Only
Forward
Only
Forward
•
•
Only
Forward
Only
•••
•••
••••••
Forward
Only
Only
•
Only
Forward
•
Only
•••
•••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
V
TIP
V
R
TR
L
I
DCMET
RING VRX
TX
E
RX
FIGURE 1. OVERLOAD LEVEL (OFF HOOK, ON HOOK)
368Ω
E
L
C10µF
C10µF
368Ω
TIP
A
RING
A
SHD
V
TX
VRX
A
300Ω
300Ω
A
LZT = VT/A
T
R
1V
RMS
0 < f < 100Hz
E
L
C
FIGURE 2. LONGITUDINAL IMPEDANCE
368Ω
A
E
C
L
368Ω
A
T
V
T
V
TIP
RING
R
TIP
RING
SHD
V
TX
VRX
LZR = VR/A
V
TX
VRX
R
V
TX
FIGURE 3A. LONGITUDINAL CURRENT LIMIT ON-HOOK (ACTIVE) FIGURE 3B. LONGITUDINAL CURRENT LIMIT OFF-HOOK (ACTIVE)
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
OFF-HOOK LONGITUDINAL BALANCE
Longitudinal to Metallic (Note 7) Forward and Reverse
4-5
Longitudinal to Metallic (Note 7) Forward and Reverse
Longitudinal to 4-Wire (Note 9) (Forward and Reverse)
Metallic to Longitudinal (Note 10) Forward and Reverse
4-Wire to Longitudinal (Note 11) Forward and Reverse
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
IEEE 455 - 1985, RLR, RLT = 368Ω Normal Polarity:
0.2kHz < f < 1.0kHz, 0oC to 70oC - - - dB 53 NA NA NA NA 55
1.0kHz < f < 3.4kHz, 0oC to 70oC - - - dB 53 NA NA NA NA 55
0.2kHz < f < 1.0kHz, -40oC to 85oC - - - dB NA 53 63 63 63 NA
1.0kHz < f < 3.4kHz, -40oC to 85oC - - - dB NA 53 58 58 58 NA Reverse Polarity 0.2kHz < f < 3.4kHz,
(Figure 4)
RLR, RLT = 300Ω, Normal Polarity:
0.2kHz < f < 1.0kHz, 0oC to 70oC - - - dB 53 NA NA NA NA 55
1.0kHz < f < 3.4kHz, 0oC to 70oC - - - dB 53 NA NA NA NA 55
0.2kHz < f < 1.0kHz, -40oC to 85oC - - - dB NA 53 63 63 63 NA
1.0kHz < f < 3.4kHz, -40oC to 85oC - - - dB NA 53 58 58 58 NA Reverse Polarity 0.2kHz < f < 3.4kHz,
(Figure 4)
Normal Polarity: Forward
o
0.2kHz < f < 1.0kHz, 0
1.0kHz < f < 3.4kHz, 0
0.2kHz < f < 1.0kHz, -40oC to 85oC - - - dB NA 53 63 63 63 NA
1.0kHz < f < 3.4kHz, -40 Reverse Polarity 0.2kHz < f < 3.4kHz,
(Figure 4) FCC Part 68, Para 68.310 (Note 8)
0.2kHz < f < 3.4kHz, (Figure 5)
0.2kHz < f < 3.4kHz, (Figure 5) 40 - - dB Forward
C to 70oC - - - dB 53 NA NA NA NA 61
o
C to 70oC - - - dB 53 NA NA NA NA 61
o
C to 85oC - - - dB NA 53 58 58 58 NA
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
MIN MIN MIN MIN MIN MIN
Forward
Only
--- dB NA53 NA 58 58 55
MIN MIN MIN MIN MIN MIN
Forward
Only
--- dB NA53 NA 58 58 55
MIN MIN MIN MIN MIN MIN
Only
- - dB NA 53 NA 58 58 61
40 50 - dB Forward
Only
Only
•
•
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
•••
•••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Electrical Specifications T
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
R
4-6
LT
E
L
C
2.16µF
R
LR
FIGURE 4. LONGITUDINAL TO METALLIC AND LONGITUDINAL TO 4-WIRE BALANCE
TIP
V
TR
RING
V
TX
VRX
V
TX
FIGURE 5. METALLIC TO LONGITUDINAL AND 4-WIRE TO LONGITUDINAL
BALANCE
2-Wire Return Loss Forward and Reverse
0.2kHz to 1.0kHz (Note 12, Figure 6) 30 35 - dB Forward
1.0kHz to 3kHz (Note 12, Figure 6) 23 25 - dB 3kHz to 3.4kHz (Note 12, Figure 6) 21 23 - dB
TIP IDLE VOLTAGE (User Programmable)
TIPX Idle Voltage Active, IL < 5mA -2.6 -2.2 -1.8 V Forward Forward and Reverse
RING IDLE VOLTAGE (User Programmable)
RINGX Idle Voltage Forward and Reverse
V
TR
Forward and Reverse V
TR(ROH)
Pulse Metering
Active, I Tip open, IL < 5mA -46.4 -45.3 -44.2 V Active, I
Active, IL≥ 8.5mA, ROH = 50kΩ 36 38.1 - V NA
< 5mA -46.4 -45.3 -44.2 V Forward
L
< 5mA 41 43.1 45 V Forward
L
Forward and Reverse
2.16µF
C
V
L
300Ω
300Ω
Only
Only
Only
Only
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
R
LT
R
LR
TIP
E
TR
RING
V
TX
VRX
E
RX
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Forward
•
•
•
•
•
Only
Forward
Only
Forward
Only
Forward
Only
NA NA
•••
•••
•••
•••
••
Z
D
TIP
R
V
S
R
R
LR
V
M
Z
IN
RING
FIGURE 6. TWO-WIRE RETURN LOSS
V
TX
VRX
TIP
V
TX
V
TX
Z
L
600Ω
V
TR
E
G
R
L
VRX
RING
FIGURE 7. OVERLOAD LEVEL (4-WIRE TRANSMIT PORT), OUTPUT OFFSET
VOLTAGE AND HARMONIC DISTORTION
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
4-WIRE TRANSMIT PORT (VTX)
Overload Level, Off Hook (IL≥ 18mA) Forward and Reverse
Overload Level, On Hook (IL≤ 5mA)
4-7
Forward and Reverse VTX Output Offset Voltage
Forward and Reverse Output Impedance
(Guaranteed by Design)
4-WIRE RECEIVE PORT (VRX)
VRX Input Impedance (Guaranteed by Design)
FREQUENCY RESPONSE (OFF-HOOK)
2-Wire to 4-Wire Forward and Reverse
4-Wire to 2-Wire Forward and Reverse
4-Wire to 4-Wire Forward and Reverse
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
(ZL > 20kΩ, IL 1% THD) (Note 13, Figure 7) TA = 0oC to 85oC TA = -40oC to 0oC
(ZL > 20kΩ, 1% THD) (Note 14, Figure 7)
EG = 0, ZL= ∞, (Note 15, Figure 7) -200 - 200 mV Forward
0.2kHz < f < 03.4kHz - 0.1 1 Ω
0.2kHz < f < 3.4kHz - 500 600 kΩ
Relative to 0dBm at 1.0kHz, ERX= 0V Forward
0.3kHz < f < 3.4kHz -0.15 - 0.15 dB f = 8.0kHz (Note 16, Figure 8) - 0.24 0.5 dB f = 12kHz (Note 16, Figure 8) - 0.58 1.0 dB f = 16kHz (Note 16, Figure 8) - 1.0 1.5 dB Relative to 0dBm at 1.0kHz, EG= 0V
0.3kHz < f < 3.4kHz -0.15 - 0.15 dB f = 8kHz (Note 17, Figure 8) -0.5 0.24 - dB f = 12kHz (Note 17, Figure 8) -1.0 0.58 - dB f = 16kHz (Note 17, Figure 8) -1.5 1.0 - dB Relative to 0dBm at 1.0kHz, EG= 0V Forward
0.3kHz < f < 3.4kHz (Note 18, Figure 8) -0.15 - 0.15 dB 8kHz, 12kHz, 16kHz (Note 18, Figure 8) -0.5 0 0.5 dB
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
Forward
3.2 - - V
3.0 - - V
1.3 - - V
PEAK PEAK
PEAK
Only
Forward
Only
Only
••••••
••••••
Only
Forward
Only
Only
•
•
•
•
•
•
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
Only
Forward
Only
Forward
Only
Forward
Only
•••
•••
•••
•••
Forward
Only
•••
Forward
Only
•••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
TIP
R
600Ω
L
V
TR
RING VRX
E
G
FIGURE 8. FREQUENCY RESPONSE, INSERTION LOSS, GAIN TRACKING
AND HARMONIC DISTORTION
V
PTG
TX
OPEN
E
RX
V
TX
V
TIP
R
L
600Ω
V
TR
RING
FIGURE 9. IDLE CHANNEL NOISE
TX
VRX
V
TX
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
INSERTION LOSS
2-Wire to 4-Wire Forward and Reverse
4-Wire to 2-Wire
4-8
Forward and Reverse
GAIN TRACKING (Ref = -10dBm, at 1.0kHz)
2-Wire to 4-Wire Forward and Reverse
4-Wire to 2-Wire Forward and Reverse
NOISE
Idle Channel Noise at 2-Wire C-Message Weighting - 10.5 13 dBrnC Forward Forward and Reverse Psophometric Weighting (Note 24,
Idle Channel Noise at 4-Wire C-Message Weighting - 10.5 13 dBrnC Forward Forward and Reverse Psophometrical Weighting
HARMONIC DISTORTION
2-Wire to 4-Wire Forward and Reverse
4-Wire to 2-Wire Forward and Reverse
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
0dBm, 1kHz PTG = Open (Note 19, Figure 8) -0.2 - 0.2 dB Forward PTG = GND (Note 20, Figure 8) -6.22 -6.02 -5.82 dB 0dBm, 1kHz (Note 21, Figure 8) -0.2 - 0.2 dB Forward
-40dBm to +3dBm (Note 22, Figure 8) -0.1 - 0.1 dB Forward
-55dBm to -40dBm (Note 22, Figure 8) -0.2 - 0.2 dB
-40dBm to +3dBm (Note 23, Figure 8) -0.1 - 0.1 dB Forward
-55dBm to -40dBm (Note 23, Figure 8) -0.2 - 0.2 dB
Note 30, Figure 9)
(Note 25, Note 30, Figure 9)
0dBm, 0.3kHz to 3.4kHz (Note 26, Figure 7)
0dBm, 0.3kHz to 3.4kHz (Note 27, Figure 8)
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
- -79.5 -77 dBmp
- -79.5 -77 dBmp
- -67 -50 dB Forward
- -67 -50 dB Forward
Only
Only
Only
Only
Only
Only
Only
Only
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
• •••
•
•
•
•
•
•
•
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
•••
•••
•••
•••
•••
•••
•••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
TIP
V
TX
R
R
L
V
600Ω
FIGURE 10. CONSTANT LOOP CURRENT TOLERANCE
TR
RING
LIM
VRX
R
LIM
38.3kΩ
7kΩ
V
BH
I
R1
R
1
FIGURE 11. TIPX VOLTAGE
TIP
S
RING
V
VRX
TX
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
BATTERY FEED CHARACTERISTICS
Constant Loop Current Tolerance 18mA ≤ IL ≤ 45mA, Forward IL = 26.5mA, R
Forward and Reverse Tip Open State TIPX Leakage
4-9
Current Tip Open State RINGX Current R1= 0Ω, VBH = -48V, R
Tip Open State RINGX Voltage 5mA < IR1 < 26mA (Figure 11) - 42.8 - V Tip Voltage (Ground Start) Active State, (S Open) R1= 150Ω
Tip Voltage (Ground Start) Active State, (S Closed) Tip Lead to
Open Circuit State Loop Current (Active) RL = 0Ω -20 0 20 µA
LOOP CURRENT DETECTOR
Programmable Threshold I Forward and Reverse I
GROUND KEY DETECTOR
Ground Key Detector Threshold Tip/Ring Current Difference
LINE VOLTAGE MEASUREMENT
Pulse Width (
RING TRIP DETECTOR (DT, DR)
Ring Trip Comparator Current Source Res = 2MΩ -2- µA Input Common-Mode Range Source Res = 2MΩ --±200 V
= 38.3kΩ
LIM
GKD_LVM) Pulse Width = (20)(C
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
(Note 27, Figure 10) 0.92I
S = Closed (Figure 11) - - -200 µA
= 38.3kΩ 22.6 26.8 31 mA
LIM
R1 = 2.5kΩ, VBH = -48V (Figure 11) 15.5 17.1 18.2 mA
(Figure 11)
-48V Through 7kΩ, Ring Lead to Ground Through 150Ω (Figure 11)
= (500/ RD) ≥ 5mA, 0.9I
LTh
= 8.5mA
LTh
R
= 58.8kΩ
D
Tip Open 5 8 11 mA Active (Note 29, R1 =2.5kΩ, Figure 12) 12.5 20 27.5 mA
REV.../ILIM
) 0.32 0.36 0.4 ms/V NA NA NA
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
I
L
-5.3 -4.8 -4.3 V NA NA NA
-5.3 -4.8 -4.3 V NA NA NA NA
LThILTh
1.08I
L
1.1I
LTh
mA
L
mA Forward
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
Only
•
Only
•••
••••••
••••••
••••••
••
NA
••
••••••
Forward
Only
•
••
Only
NA
•••
••
NA
•••
••••••
••••••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
RING RELAY DRIVER
V
at 30mA IOL = 30mA - 0.2 0.5 V
SAT
V
at 40mA IOL = 40mA - 0.52 0.8 V
SAT
Off State Leakage Current VOH = 13.2V - 0.1 10 µA
4-10
TEST RELAY DRIVER (TRLY1, TRLY2)
V
at 30mA I
SAT
V
at 40mA I
SAT
Off State Leakage Current V
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
= 30mA - 0.3 0.5 V NA NA NA/• NA/• NA/• NA/•
OL
= 40mA - 0.62 0.9 V NA NA NA/• NA/• NA/• NA/•
OL
= 13.2V - - 10 µA NA NA NA/• NA/• NA/• NA/•
OH
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
••••••
••••••
••••••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
TIP
RING
2.5kΩ
FIGURE 12. GROUND KEY DETECT
DIGITAL INPUTS (C1, C2, C3)
Input Low Voltage, V Input High Voltage, V Input Low Current, I Input High Current, I
DETECTOR OUTPUTS (SHD, GKD_LVM)
SHD Output Low Voltage, V Forward, Reverse
SHD Output High Voltage, V Forward, Reverse
GKD_LVM Output Low Voltage, VOLForward and Tip Open
GKD_LVM Output High Voltage, VOHForward and Tip Open
Internal Pull-Up Resistor - 15 - kΩ
IL
IH
IL
IH
OL
OH
VIL = 0.4V - - -10 µA VIH = 2.5V - 25 50 µA
IOL = 1mA - - 0.5 V Forward
IOH = 100µA 2.7 - - V Forward
IOL = 1mA R1 = 2.5kΩ (Figure 11)
IOH = 100µA 2.7 - - V GKD GKD NA GKD_
0 - 0.8 V
2.0 - V
- - 0.5 V GKD GKD NA GKD_
CC
V
TX
VRX
SHD
V
••••••
••••••
••••••
••••••
Forward
Only
Only
•
•
Only
Forward
Only
•••
•••
LVM
LVM
GKD_
LVM
GKD_
LVM
LVM
LVM
••••••
Electrical Specifications T
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS HC55120 HC55121 HC55130/1 HC55140/1 HC55142/3 HC55150/1
POWER DISSIPATION (VBH = -48V, VBL = -24V)
Open Circuit State C1, C2, C3 = 0, 0, 0 - 25 - mW Forward
On-Hook, Active C1, C2, C3 = 0, 1, 0
4-11
Forward and Reverse IL= 0mA, Longitudinal
POWER SUPPLY CURRENTS (VBH = -48V, VBL = -24V)
VCC Current, I
VBH Current, I
VBL Current, I
VCC Current, I Forward and Reverse
VBH Current, I Forward and Reverse
VBL Current, I Forward and Reverse
POWER SUPPLY REJECTION RATIOS
VCC to 2 or 4 Wire Port Forward and Reverse
VBH to 2 or 4 Wire Port Forward and Reverse
VBL to 2 or 4 Wire Port Forward and Reverse
TEMPERATURE GUARD
Junction Threshold Temperature - 175 -
CC
BH
BL
CC
BH
BL
= -40oCto85oC, VCC= +5V ±5%, VBH= -48V,VBL= -24V,PTG = Open, RP1=RP2=0Ω, ZT= 120kΩ,R
A
ROH= 40kΩ,CH= 0.1µF, CDC= 4.7µF, C to the part. (NA) symbol used to indicate the test does not apply to the part. (Continued)
C1, C2, C3 = 1, 1, 0
Current = 0mA
Open Circuit State - 2.25 3.0 mA Forward
Active State IL= 0mA, Longitudinal Current = 0mA
Active State RL = 600Ω 50Hz < f < 3400Hz, V
=100mV
IN
= 0.47µF, GND = 0V, RL = 600Ω. Unless Otherwise Specified.
RT/REV
- 52 - mW Forward
- 0.3 0.45 mA Forward
- 0.022 0.035 mA Forward
- 2.7 3.6 mA Forward
- 0.8 1.06 mA Forward
- - 0.01 mA Forward
- 40 - dB Forward
- 40 - dB Forward
- 40 - dB Forward
o
C•
Only
Only
Only
Only
Only
Only
Only
Only
Only
Only
Only
= 38.3kΩ,RD= 50kΩ, RDC_RAC = 20kΩ,
LIM
Symbol used to indicate the test applies
(•)
Forward
•
Only
•••
• •••
Forward
•
•
•
•
•
•
•
•
•
•
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
Forward
Only
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••
•••••
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
Loading...
+ 24 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use