Intersil Corporation HA-5137A Datasheet

TM

HA-5137A

Data Sheet April 2000

63MHz, Ultra-Low Noise Precision
Operational Amplifier

The HA-5137 operational amplifier features an unparalleled
combination of precision DC and wideband high speed
characteristics. Utilizing the Intersil Dielectric Isolation
technology and advanced processing techniques, this
unique design unites low noise precision
instrumentation performance with high speed (20V/µs)
wideband capability.

This amplifier’s impressive list of features include low V
(10µV), wide gain bandwidth (63MHz), high open loop gain
(1800V/mV), and high CMRR (126dB). Additionally, this
flexible device operates over a wide supply range (±5V to
±20V) while consuming only 140mW of power.

Using the HA-5137 allowsdesignerstominimizeerrorswhile
maximizing speed and bandwidth in applications requiring
gains greater than five.

This device is ideally suited for low level transducer signal
amplifier circuits. Other applications which can utilize the
HA-5137’squalitiesinclude instrumentation amplifiers, pulse
or RF amplifiers, audio preamplifiers, and signal conditioning
circuits.

This device can easily be used as a design enhancement by
directly replacing the 725, OP25, OP06, OP07, OP27 and
OP37 where gains are greater than five. For the military
grade product, refer to the HA-5137/883 data sheet.

⁄()

3nV Hz

OS

File Number 2908.5

Features

• Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/µs

• Wide Gain Bandwidth (A

• Low Noise. . . . . . . . . . . . . . . . . . . . . . . at 1kHz

•Low V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10µV

OS

≥ 5) . . . . . . . . . . . . . . . 63MHz

V

3nV/ Hz

• High CMRR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126dB

• High Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800V/mV

Applications

• High Speed Signal Conditioners

• Wide Bandwidth Instrumentation Amplifiers

• Low Level Transducer Amplifiers

• Fast, Low Level Voltage Comparators

• Highest Quality Audio Preamplifiers

• Pulse/RF Amplifiers

• For Further Design Ideas See Application Note AN553

Ordering Information

TEMP.

PART NUMBER

HA7-5137A-5 0 to 75 8 Ld CERDIP F8.3A

RANGE (oC) PACKAGE

PKG.

NO.

Pinout

BAL

-IN

+IN

HA-5137A

(CERDIP)

TOP VIEW

1

2

-

+

3

4

V-

1

8

BAL

7

V+

OUT

6

NC

5

1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Corporation. | Copyright © Intersil Corporation 2000

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

HA-5137A

Absolute Maximum Ratings T

Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 44V

Differential Input Voltage (Note 1) . . . . . . . . . . . . . . . . . . . . . . . 0.7V

Output Current. . . . . . . . . . . . . . . . . . . .Full Short Circuit Protection

Operating Conditions

Temperature Range

HA-5137A-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. For differential input voltages greater than 0.7V, the input current must be limited to 25mA to protect the back-to-back input diodes.

2. θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications V

PARAMETER TEST CONDITIONS

INPUT CHARACTERISTICS

Offset Voltage 25 - 10 25 µV

Average Offset Voltage Drift Full - 0.2 0.6 µV/oC
Bias Current 25 - 10 40 nA

Offset Current 25 - 7 35 nA

Common Mode Range Full ±10.3 ±11.5 - V
Differential Input Resistance (Note 3) 25 1.5 6 - MΩ
Input Noise Voltage (Note 4) 0.1Hz to 10Hz 25 - 0.08 0.18 µV
Input Noise Voltage Density

(Note 5)

Input Noise Current Density
(Note 5)

TRANSFER CHARACTERISTICS

Large Signal Voltage Gain RL = 2kΩ,

Common Mode Rejection Ratio VCM = ±10V Full 114 126 - dB
Minimum Stable Gain 25 5 - - V/V
Gain-Bandwidth-Product f = 10kHz 25 60 80 - MHz

OUTPUT CHARACTERISTICS

Output Voltage Swing RL = 600Ω 25 ±10.0 ±11.5 - V

Full Power Bandwidth (Note 6) 25 220 320 - kHz
Output Resistance Open Loop 25 - 70 - Ω
Output Current 25 16.5 25 - mA
TRANSIENT RESPONSE (Note 7)
Rise Time 25 - - 100 ns
Slew Rate V
Settling Time Note 8 25 - 1.0 - µs
Overshoot 25 - 20 40 %

POWER SUPPLY CHARACTERISTICS

Supply Current 25 - 3.5 - mA

=25oC Thermal Information

A

Thermal Resistance (Typical, Note 2) θJA (oC/W) θJC (oC/W)

CERDIP Package. . . . . . . . . . . . . . . . . 115 28

Maximum Junction Temperature (Hermetic Package) . . . . . . . 175oC

Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

= ±15V, CL≤ 50pF, RS≤ 100Ω

SUPPLY

TEMP.

(oC) MIN TYP MAX UNITS

Full - 30 60 µV

Full - 20 60 nA

Full - 15 50 nA

f = 10Hz 25 - 3.5 8.0
f = 100Hz 25 - 3.1 4.5
f = 1000Hz 25 - 3.0 3.8
f = 10Hz 25 - 1.7 4.0
f = 100Hz 25 - 1.0 2.3
f = 1000Hz 25 - 0.4 0.6

25 1000 1800 - V/mV

V

= ±10V

OUT

f = 1MHz 25 - 63 - MHz

RL = 2kΩ Full ±11.7 ±13.8 - V

= ±3V 25 14 20 - V/µs

OUT

Full 600 1200 - V/mV

Full - - 4.0 mA

P-P

nV/ Hz
nV/ Hz

nV/ Hz
pA/ Hz

pA/ Hz
pA/ Hz

2

HA-5137A

Electrical Specifications V

= ±15V, CL≤ 50pF, RS≤ 100Ω (Continued)

SUPPLY

TEMP.

PARAMETER TEST CONDITIONS

(oC) MIN TYP MAX UNITS

Power Supply Rejection Ratio VS = ±4V to ±18V Full - 2 4 µV/V

NOTES:

3. This parameter value is based upon design calculations.

4. Refer to Typical Performance section of the data sheet.

5. The limits for this parameter are based on lab characterization, and reflect lot-to-lot variation.

6. Full power bandwidth guaranteed based on slew rate measurement using: .

FPBW

7. Refer to Test Circuits section of the data sheet.

Slew Rate

---------------------------- -=

2πV

PEAK

8. Settling time is specified to 0.1% of final value for a 10V output step and AV = -5.

Test Circuits and Waveforms

IN

FIGURE 1. LARGE AND SMALL SIGNAL RESPONSE TEST CIRCUIT

+

-

1.6kΩ

400Ω

OUT

50pF

OUT

IN

Vertical Scale: Input = 1V/Div.

Horizontal Scale: 1µs/Div.

LARGE SIGNAL RESPONSE

IN

Output = 5V/Div.

1000Ω

400Ω

2N4416

5kΩ

+

-

-15V
2kΩ

+15V

+15V

2kΩ

50pF

OUT

IN

OUT

Vertical Scale: Input = 20mV/Div.

Output = 100mV/Div.

Horizontal Scale: 100ns/Div.

SMALL SIGNAL RESPONSE

TO
OSCILLOSCOPE

NOTES:

9. AV = -5.

10. Feedbackand summing resistors should be

0.1% matched.

11. Clipping diodes are optional. HP5082-2810
recommended.

FIGURE 2. SETTLING TIME TEST CIRCUIT

3