intersil HA-5102, HA-5104 DATA SHEET

®

www.BDTIC.com/Intersil

HA-5102, HA-5104

Data Sheet October 26, 2004

Dual and Quad, 8MHz, Low Noise
Operational Amplifiers

Low noise and high performance are key words describing
HA-5102 and HA-5104. These general purpose amplifiers
offer an array of dynamic specifications including a 3V/µs
slew rate and 8MHz bandwidth. Complementing these
outstanding parameters is a very low noise specification of

4.3nV/√Hz

at 1kHz.

Fabricated using the Intersil high frequency DI process,
these operational amplifiers also offer excellent input
specifications such as a 0.5mV offset voltage and 30nA
offset current. Complementing these specifications are
108dB open loop gain and 60dB channel separation.
Consuming a very modest amount of power (90mW/
package for duals and 150mW/package for quads),
HA-5102/04 also provide 15mA of output current.

This impressive combination of features make this series of
amplifiers ideally suited for designs ranging from audio
amplifiers and active filters to the most demanding signal
conditioning and instrumentation circuits.

These operational amplifiers are available in dual or quad
form with industry standard pinouts allowing for immediate
interchangeability with most other dual and quad operational
amplifiers.

HA-5102 Dual, Comp. HA-5104 Quad, Comp.
Refer to the /883 data sheet for military product.

Ordering Information

PART NUMBER

(oC) PACKAGE

HA7-5102-2 -55 to 125 8 Ld CERDIP F8.3A
HA1-5104-2 -55 to 125 14 Ld CERDIP F14.3
HA9P5104-9 -40 to 85 16 Ld SOIC M16.3

TEMP. RANGE

PKG.

DWG. #

FN2925.9

Features

• Low Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3nV/√Hz

• Bandwidth . . . . . . . . . . . . . . . . . . . 8MHz (Compensated)

• Slew Rate. . . . . . . . . . . . . . . . . . . . 3V/µs (Compensated)

• Low Offset Voltage. . . . . . . . . . . . . . . . . . . . . . . . . 0.5mV

• Available in Duals or Quads

Applications

• High Q, Active Filters

• Audio Amplifiers

• Instrumentation Amplifiers

• Integrators

• Signal Generators

• For Further Design Ideas, See Application Note AN554

Pinouts

HA-5102 (CERDIP)

TOP VIEW

OUT1

1
2

-IN1

+IN1

-

+

3
4

V-

HA-5104 (CERDIP)

TOP VIEW

OUT1

1

-IN1

+IN1

V+

+IN2

-IN2

OUT2

1

2

-

+

3
4
5

+

-

6

2

7

8

V+

7

OUT2

6

-IN2

-

+

5

+IN2

14

OUT4

4

13

-IN4

-

+

12

+IN4

11

V-

10

+IN3

+

­9

-IN3

3

8

OUT3

1

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143

| Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

HA5104 (SOIC)

TOP VIEW

OUT1

1

-IN1

+IN1

V+

+IN2

-IN2

OUT2

NC

Copyright © Intersil Americas Inc. 2003, 2004. All Rights Reserved

14

2

-

+

3
4
5

+

-

6

23

7
8

OUT4

16

-IN4

15

-

+

+IN4

14

V-

13

+IN3

12

+

­11

-IN3

10

OUT3

9

NC

HA-5102, HA-5104

www.BDTIC.com/Intersil

Absolute Maximum Ratings Thermal Information

Supply Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . 40V

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V

Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±V

Output Short Circuit Duration (Note 3). . . . . . . . . . . . . . . . Indefinite

SUPPLY

Operating Conditions

Temperature Range

HA-510X-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55

HA-5104-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 175
packages, and below 150

2. θ

is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

JA

3. Any one amplifier may be shorted to ground indefinitely.

o

C for plastic packages.

o

C to 125oC

o

C to 85oC

Thermal Resistance (Typical, Note 2) θ

8 Lead CERDIP Package. . . . . . . . . . . 115 28

14 Lead CERDIP Package. . . . . . . . . . 75 20

SOIC Package . . . . . . . . . . . . . . . . . . . 100 N/A

Maximum Junction Temperature (Note 1 , Hermetic P ackage) . .175

Maximum Junction Temperature (Plastic Package) . . . . . . . .150

Maximum Storage Temperature Range. . . . . . . . . . -65

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300

(SOIC - Lead Tips Only)

(oC/W) θJC (oC/W)

JA

o

C to 150oC

o

C for hermetic

o
o

o

C
C

C

Electrical Specifications V

PARAMETER

INPUT CHARACTERISTICS

Offset Voltage 25 - 0.5 2.0 - 0.5 2.5 - 0.5 2.5 mV

Offset Voltage Average Drift Full - 3 - - 3 - - 3 - µV/
Bias Current 25 - 130 200 - 130 200 - 130 200 nA

Offset Current 25 - 30 75 - 30 75 - 30 75 nA

Input Resistance 25 - 500 - - 500 - - 500 - kΩ
Common Mode Range Full ±12 - - ±12 - - ±12 - - V

TRANSFER CHARACTERISTICS

Large Signal Voltage Gain,

= ±5V, RL = 2kΩ)

(V

OUT

Common Mode Rejection Ratio (V
Small Signal Bandwidth, (A
Channel Separation (Note 4) 25 - 60 - - 60 - - 60 - dB

OUTPUT CHARACTERISTICS

Output Voltage Swing (R

Output Current, (V
Full Power Bandwidth (Note 5) 25 16 47 - 16 47 - 16 47 - kHz
Output Resistance 25 - 110 - - 110 - - 110 - Ω

STABILITY

Minimum Stable Closed Loop Gain Full 1 - - 1 - - 1 - - V/V
TRANSIENT RESPONSE (Note 6)

= ±5V) Full ±10 ±15 - ±10 ±15 - ±7 ±15 - mA

OUT

CM

= 1) 25-8--8--8-MHz

V

L

(R

L

= ±15V, Unless Otherwise Specified

SUPPLY

TEMP.

o

(

C)

Full--2.5--3.0--3.0mV

Full - - 325 - - 325 - - 500 nA

Full - - 125 - - 125 - - 125 nA

25 100 250 - 100 250 - 80 250 - kV/V

Full 100 - - 100 - - 80 - - kV/V

= ±5.0V) Full 86 95 - 86 95 - 80 95 - dB

= 10kΩ)Full±12 ±13 - ±12 ±13 - ±12 ±13 - V
= 2kΩ)Full±10 ±12 - ±10 ±12 - ±10 ±12 - V

HA-5102-2 HA-5104-2 HA-5104-9

UNITSMIN TYP MAX MIN TYP MAX MIN TYP MAX

o

C

2

FN2925.9

HA-5102, HA-5104

www.BDTIC.com/Intersil

Electrical Specifications V

PARAMETER

Rise Time 25 - 108 200 - 108 200 - 108 200 ns
Overshoot 25 - 20 35 - 20 35 - 20 35 %
Slew Rate 25 1 3 - 1 3 - 1 3 - V/µs
Settling Time (Note 7) 25 - 4.5 - - 4.5 - - 4.5 - µs
NOISE CHARACTERISTICS (Note 8)
Input Noise Voltage f = 10Hz 25 - 9 25 - 9 25 - 9 25 nV/√Hz

f = 1kHz 25 - 4.3 6.0 - 4.3 6.0 - 4.3 6.0 nV/√Hz

Input Noise Current f = 10Hz 25 - 5.1 15 - 5.1 15 - 5.1 15 pA/√Hz

f = 1kHz 25 - 0.57 3 - 0.57 3 - 0.57 3 pA/√Hz

Broadband Noise Voltage f = DC to 30kHz 25 - 870 - - 870 - - 870 - nV

POWER SUPPLY CHARACTERISTICS

Supply Current (All Amps) 25 - 3.0 5.0 - 5.0 6.5 - 5.0 6.5 mA
Power Supply Rejection Ratio, (∆V

NOTES:

4. Channel separation value is referred to the input of the amplifier. Input test conditions are: f = 10kHz; V

5. Full power bandwidth is guaranteed by equation: .

6. Refer to Test Circuits section of the data sheet.

7. Settling time is measured to 0.1% of final value for a 10V input step, A

8. The limits for these parameters are guaranteed based on lab characterization, and reflect lot-to-lot variation.

S

= ±15V, Unless Otherwise Specified (Continued)

SUPPLY

TEMP.

o

(

C)

= ±5V) Full 86 100 - 86 100 - 80 100 - dB

Full power bandwidth

HA-5102-2 HA-5104-2 HA-5104-9

= -1.

V

Slew Rate

---------------------------- -=

2π V

PEAK

= 100mV

IN

PEAK

; RS = 1kΩ.

UNITSMIN TYP MAX MIN TYP MAX MIN TYP MAX

RMS

3

FN2925.9

Test Circuits and Waveforms

www.BDTIC.com/Intersil

2kΩ

HA-5102, HA-5104

IN

2kΩ

1kΩ

-

+

50pF

OUTPUT

Vertical = 5V/Div., Horizontal = 5µs/Div. (AV = -1)

FIGURE 1. LARGE SIGNAL RESPONSE CIRCUIT

INPUT

OUT

+5V

0V

-5V

+5V

0V

-5V

IN

+

-

2kΩ

OUTPUT

200mV

INPUT

0V

Vertical = 40mV/Div., Horizontal = 50ns/Div. (AV = +1)

FIGURE 2. SMALL SIGNAL RESPONSE CIRCUIT

50pF

5kΩ

500Ω (NOTE 9)

V

IN

200Ω (NOTE 9)

2kΩ

NOTES:

= -1.

9. A

V

10. Feedback and summing resistors should be 0.1% matched.

11. Clipping diodes are optional, HP5082-2810 recommended.

FIGURE 3. SETTLING TIME CIRCUIT

+15V

2N4416

5kΩ

+15V

+

TO
OSCILLOSCOPE

2kΩ

V

OUT

-

-15V

2kΩ

50pF

4

FN2925.9