Intersil Corporation HA-5002-883 Datasheet
July 1994
HA-5002/883
Monolithic, Wideband, High Slew Rate,
High Output Current Buffer
Features
• This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.
• Voltage Gain (R
= 1kΩ). . . . . . . . . . . . . . . . . .0.98 (Min)
L
0.995 (Typ)
(R
= 100Ω) . . . . . . . . . . . . . . . .0.96 (Min)
L
0.971 (Typ)
• High Input Impedance . . . . . . . . . . . . . . . . .1.5MΩ (Min)
3MΩ (Typ)
• Low Output Impedance. . . . . . . . . . . . . . . . . . 5Ω (Max)
3Ω (Typ)
• Very High Slew Rate . . . . . . . . . . . . . . . 1000V/µs (Min)
1300V/µs (Typ)
• Wide Small Signal Bandwidth. . . . . . . . . .110MHz (Typ)
• High Output Current . . . . . . . . . . . . . . . . . 100mA (Min)
• High Pulsed Output Current . . . . . . . . . . .400mA (Max)
• Monolithic Dielectric Isolation Construction
• Replaces Hybrid LH0002
Applications
• Line Driver
• Data Acquisition
• 110MHz Buffer
• High Power Current Booster
• High Power Current Source
• Sample and Holds
• Radar Cable Driver
• Video Products
Description
The HA-5002/883 is a monolithic, wideband, high slew rate,
high output current, buffer amplifier.
Utilizing the advantages of the Harris Dielectric Isolation technologies, the HA-5002/883 current buffer offers 1300V/µs
slew rate typically and 1000V/µs minimum with 110MHz of
bandwidth. The ±100mA minimum output current capability is
enhanced by a 3Ω output impedance.
The monolithic HA-5002/883 will replace the hybrid LH0002
with corresponding performance increases. These characteristics range from the 3MΩ (typ) input impedance to the
increased output voltage swing. Monolithic design technologies have allowed a more precise buffer to be developed
with more than an order of magnitude smaller gain error. The
voltage gain is 0.98 guaranteed minimum with a 1kΩ load
and 0.96 minimum with a 100Ω load.
The HA-5002/883 will provide many present hybrid users
with a higher degree of reliability and at the same time
increase overall circuit performance.
Ordering Information
PART
NUMBER
HA2-5002/883 -55oC to +125oC 8 Pin Can
HA4-5002/883 -55oC to +125oC 20 Lead Ceramic LCC
HA7-5002/883 -55oC to +125oC 8 Lead CerDIP
TEMPERATURE
RANGE PACKAGE
Pinouts
HA-5002/883
(CERDIP)
TOP VIEW
V
+
1
1
V2-
2
3
NC
4
IN
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
http://www.intersil.com or 407-727-9207
8
OUT
7
V2+
NC
6
-
V
5
1
| Copyright © Intersil Corporation 1999
NC
V
NC
NC
NC
HA-5002/883
NCNCNC
3212019
4
-
5
2
6
7
8
9101112
NC
(CLCC)
TOP VIEW
+
1
V
IN
NC
3-258
OUT
-
1
V
18
NC
V2+
17
16
NC
NC
15
NC
14
13
NC
HA-5002/883
(METAL CAN)
TOP VIEW
IN
V
+
1
2
NC NC
Spec Number
8
1
3
4
OUT
V
7
6
5
511017-883
File Number 3705
-
1
V2-V2+
Specifications HA-5002/883
Absolute Maximum Ratings Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 44V
Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equal to Supplies
Peak Output Current (50ms On, 1s Off). . . . . . . . . . . . . . . . . .±400mA
Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC
Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC
ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <4000V
Lead Temperature (Soldering 10s). . . . . . . . . . . . . . . . . . . . +300oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range. . . . . . . . . . . . . . . . -55oC to +125oC
Operating Supply Voltage. . . . . . . . . . . . . . . . . . . . . . . . .±12V to ±15V
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS
Device Tested at: V
PARAMETERS SYMBOL CONDITIONS
= ±12V and ±15V, R
SUPPLY
SOURCE
= 50Ω, C
Thermal Resistance θ
CerDIP Package . . . . . . . . . . . . . . . . . . . 115oC/W 28oC/W
Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W
Metal Can Package. . . . . . . . . . . . . . . . . 155oC/W 67oC/W
Package Power Dissipation Limit at +75oC for TJ≤ +175oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .870mW
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W
Metal Can Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 645mW
Package Power Dissipation Derating Factor Above +75oC
CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.7mW/oC
Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . .15.4mW/oC
Metal Can Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5mW/oC
RL≥ 100Ω
≤ 10pF, VIN = 0V, Unless Otherwise Specified.
LOAD
LIMITS
GROUP A
SUBGROUPS TEMPERATURE
JA
θ
JC
UNITSMIN MAX
Input Offset
V
IO1
Voltage
V
IO2
Input Bias Current I
B1
I
B2
Voltage Gain 1 +AV
-AV
Voltage Gain 2 +AV
-AV
Voltage Gain 3 +AV
1
1
2
2
3
V
= ±15V 1 +25oC -20 20 mV
SUP
2, 3 +125oC, -55oC -30 30 mV
V
= ±12V 1 +25oC -20 20 mV
SUP
2, 3 +125oC, -55oC -30 30 mV
V
= ±15V, RS = 1kΩ 1 +25oC-77µA
SUP
2, 3 +125oC, -55oC -10 10 µA
V
= ±12V, RS = 1kΩ 1 +25oC-77µA
SUP
2, 3 +125oC, -55oC -10 10 µA
V
= ±12V, RL = 1kΩ,
SUP
1 +25oC 0.98 - V/V
VIN = 10V
2, 3 +125oC, -55oC 0.98 - V/V
V
= ±12V, RL = 1kΩ,
SUP
1 +25oC 0.98 - V/V
VIN = -10V
2, 3 +125oC, -55oC 0.98 - V/V
V
= ±12V, RL = 100Ω,
SUP
1 +25oC 0.96 - V/V
VIN = 10V
V
= ±12V, RL = 100Ω,
SUP
1 +25oC 0.96 - V/V
VIN = -10V
V
= ±15V, RL = 100Ω,
SUP
1 +25oC 0.96 - V/V
VIN = 10V
-AV
3
V
= ±15V, RL = 100Ω,
SUP
VIN = -10V
1 +25oC 0.96 - V/V
Spec Number 511017-883
3-259
Loading...