Intersil Corporation HA4314B Datasheet

HA4314B

Data Sheet January 1999 File Number 3679.7

400MHz, 4 x 1 Video Crosspoint Switch

The HA4314B is a very wide bandwidth 4 x 1 crosspoint
switch ideal for professional video switching, HDTV,
computer monitor routing, and other high performance
applications. The circuit features very low power dissipation
(105mW Enabled, 4mW Disabled), excellentdifferential gain
and phase, and very high off isolation. When disabled, the
output is switched to a high impedance state, making the
HA4314B ideal for routing matrix equipment.

The HA4314B requires no external current source, and
features fast switching and symmetric slew rates.

For a 4 x 1 crosspoint with Tally outputs (channel indicators)
or with synchronous control signals, please refer to the
HA4404B and HA4344B data sheets, respectively.

For audio channels requiring larger signal swings, please
refer to the CD74HC22106 (8 x 8), CD22M3493 (12 x 8),
and CD22M3494 (16 x 8) data sheets.

Ordering Information

TEMP.

PART NUMBER

HA4314BCP 0 to 70 14 Ld PDIP E14.3
HA4314BCB 0 to 70 14 Ld SOIC M14.15
HA4314BCB96 0 to 70 14 LdSOIC Tapeand

HA4314BCA 0 to 70 16 Ld SSOP M16.15A
HA4314BCA96 0 to 70 16 Ld SSOP Tape

RANGE (oC) PACKAGE

Reel

and Reel

PKG.

NO.

M14.15

M16.15A

Truth Table

CS A1 A0 OUT

000IN0
001IN1
010IN2
011IN3
1 X X HIGH - Z

Features

• Low Power Dissipation . . . . . . . . . . . . . . . . . . . . . 105mW

• Symmetrical Slew Rates . . . . . . . . . . . . . . . . . . 1400V/µs

• 0.1dB Gain Flatness. . . . . . . . . . . . . . . . . . . . . . . 100MHz

• -3dB Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . 400MHz

• Off Isolation (100MHz) . . . . . . . . . . . . . . . . . . . . . . . 70dB

• Crosstalk Rejection (30MHz) . . . . . . . . . . . . . . . . . . 80dB

• Differential Gain and Phase . . . . . . . 0.01%/0.01 Degrees

• High ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . >2000V

• TTL Compatible Control Inputs

• Improved Replacement for GX4314 and GX4314L

Applications

• Professional Video Switching and Routing

• HDTV

• Computer Graphics

• RF Switching and Routing

• PCM Data Routing

Pinouts

HA4314B (PDIP, SOIC)

TOP VIEW

14

1

IN0

GND

2

IN1

3

GND

4

IN2

5

GND

6
7

IN3

HA4314B (SSOP)

1

IN0

GND

2
3

IN1

GND

4

IN2

5

GND

6
7

IN3

GND

TOP VIEW

V+

13

A0

12

A1
CS

11

OUT

10

9

NC

8

V-

16

V+

15

A0

14

A1
CS

13

OUT

12
11

NOTE
NOTE

10

V-

98

NOTE: These pins must be left floating or connected to ground.

1

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143

| Copyright © Intersil Corporation 1999

HA4314B

Absolute Maximum Ratings Thermal Information

Voltage Between V+ and V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V

Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V

Digital Input Current (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . ±25mA

Analog Input Current (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . ±5mA

Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA

ESD Rating

Human Body Model (Per MIL-STD-883 Method 3015.7). . . .2000V

SUPPLY

Operating Conditions

Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 70oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. θJA is measured with the component mounted on an evaluation PC board in free air.

2. If an input signal is applied before the supplies are powered up, the input current must be limited to these maximum values.

Thermal Resistance (Typical, Note 1) θJA (oC/W)

PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

SSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . 175oC

Maximum Junction Temperature (Plastic Package) . . . . . . . 150oC

Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC and SSOP - Lead Tips Only)

Electrical Specifications V

PARAMETER TEST CONDITIONS

DC SUPPLY CHARACTERISTICS

Supply Voltage Full ±4.5 ±5.0 ±5.5 V
Supply Current (V

ANALOG DC CHARACTERISTICS

Output Voltage Swing without Clipping V

Output Current Full 15 20 - mA
Input Bias Current Full - 30 50 µA
Output Offset Voltage Full -10 - 10 mV
Output Offset Voltage Drift (Note 3) Full - 25 50 µV/oC

SWITCHING CHARACTERISTICS

Turn-On Time 25 - 160 - ns
Turn-Off Time 25 - 320 - ns
Output Glitch During Switching 25 - ±10 - mV

DIGITAL DC CHARACTERISTICS

Input Logic High Voltage Full 2 - - V
Input Logic Low Voltage Full - - 0.8 V
Input Current 0V to 4V Full -2 - 2 µA

AC CHARACTERISTICS

Insertion Loss 1V

Channel-to-Channel Insertion Loss Match Full - ±0.004 ±0.006 dB

-3dB Bandwidth RS=50Ω, CL= 10pF 25 - 400 - MHz

= 0V) VCS= 0.8V 25, 70 - 10.5 13 mA

OUT

= ±5V, RL = 10kΩ, VCS= 0.8V, Unless Otherwise Specified

SUPPLY

(NOTE 4)

TEMP. (oC) MIN TYP MAX UNITS

VCS= 0.8V 0 - - 15.5 mA
VCS= 2.0V 25, 70 - 400 450 µA
VCS= 2.0V 0 - 400 580 µA

OUT=VIN

P-P

RS=20Ω, CL= 20pF 25 - 280 - MHz
RS=16Ω, CL= 36pF 25 - 140 - MHz
RS=13Ω, CL= 49pF 25 - 110 - MHz

± VIO± 20mV 25, 70 ±2.7 ±2.8 - V

0 ±2.4 ±2.5 - V

25 - 0.055 0.063 dB

Full - 0.07 0.08 dB

2

HA4314B

Electrical Specifications V

PARAMETER TEST CONDITIONS

±0.1dB Flat Bandwidth RS=50Ω, CL= 10pF 25 - 100 - MHz

Input Resistance Full 200 400 - kΩ
Input Capacitance Full - 1.5 - pF
Enabled Output Resistance Full - 15 - Ω
Disabled Output Capacitance VCS= 2.0V Full - 2.5 - pF
Differential Gain 4.43MHz, Note 3 25 - 0.01 0.02 %
Differential Phase 4.43MHz, Note 3 25 - 0.01 0.02 Degrees
Off Isolation 1V

Crosstalk Rejection 1V
Slew Rate (1.5V

Total Harmonic Distortion 10MHz, RL=1kΩ, Note 3 Full - 0.01 0.1 %
Disabled Output Resistance VCS= 2.0V Full - 12 - MΩ

NOTES:

3. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation.

4. Units are 100% tested at 25oC; Guaranteed but not tested at 0oC and 70oC.

, +SR/-SR) RS=50Ω, CL= 10pF 25 - 1425/1450 - V/µs

P-P

= ±5V, RL = 10kΩ, VCS= 0.8V, Unless Otherwise Specified (Continued)

SUPPLY

(NOTE 4)

TEMP. (oC) MIN TYP MAX UNITS

RS=20Ω, CL= 20pF 25 - 100 - MHz
RS=16Ω, CL= 36pF 25 - 85 - MHz
RS=13Ω, CL= 49pF 25 - 75 - MHz

, 100MHz, VCS= 2.0V,

P-P

RL=10Ω

, 30MHz Full - 80 - dB

P-P

RS=20Ω, CL= 20pF 25 - 1010/1010 - V/µs
RS=16Ω, CL= 36pF 25 - 725/750 - V/µs
RS=13Ω, CL= 49pF 25 - 600/650 - V/µs

Full - 70 - dB

AC Test Circuit

500Ω

400Ω 510Ω

HA4314

V

IN

75Ω

NOTE: CL = CX + Test Fixture Capacitance.

R

S

C

X

10kΩ

-

+

HFA1100

75Ω

V

OUT

PC Board Layout

The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The use of low

inductance components such as chip resistors and chip
capacitors is strongly recommended, while a solid
ground plane is a must!

Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
(0.1µF) chip capacitor works well in most cases.

Keep input and output traces as short as possible, because
trace inductance and capacitance can easily become the
performance limiting items.

Application Information

General

The HA4314B is a 4 x 1 crosspoint switch that is ideal forthe
matrix element of high performance switchers and routers.
This crosspoint’s low input capacitance and high input
resistance provide excellent video terminations when used
with an external 75Ω resistor. Nevertheless, if several
HA4314B inputs are connected together, the use of an input
buffer should be considered (see Figure 1). This crosspoint
contains no feedback or gain setting resistors, so the output
is a true high impedance load when the IC is disabled
(

CS = 1).

Ground Connections

All GND pins are connected to a common point on the die,
so any one of them will suffice as the functional GND
connection. For the best isolation and crosstalk rejection,
however, all GND pins must connect to the GND plane.

Frequency Response

Most applications utilizing the HA4314B require a series
output resistor,R

, to tune the response for the specific load

S

3