Intersil Corporation HA-2842 Datasheet

HA-2842

Data Sheet September 1998 File Number 2766.5

80MHz, High Slew Rate, High Output
Current, Video Operational Amplifier

The HA-2842 is a wideband, high slew rate, operational
amplifier featuring an outstanding combination of speed,
bandwidth, and output drive capability. This amplifier’s
performance is further enhanced through stable operation
down to closed loop gains of +2, the inclusion of offset null
controls, and by its excellent video performance.

The capabilities of the HA-2842 are ideally suited for high
speed cable driver circuits, where lowclosedloopgainsand
high output drive are required. With a 6MHz full power
bandwidth, this amplifier is well suited for high frequency
signal conditioning circuits and video amplifiers. Gain
flatness of 0.035dB, combined with differential gain and
phase specifications of 0.02%, and 0.03 degrees,
respectively, make the HA-2842 ideal for component and
composite video applications.

A zener/nichrome based reference circuit, coupled with
advanced laser trimming techniques, yields a supply current
with a low temperature coefficient and low lot-to-lot variability.
For example, the aver ageI
<600µA (±2%), while the standard deviation of the I

variation from 85oCto-40oCis

CC

CC

distribution is <0.1mA (0.8%) at 25oC. Tighter ICC control
translates to more consistent AC parameters ensuring that
units from each lot perform the same way,and easing the task
of designing systems for wide temperature ranges. Critical AC
parameters, Slew Rate and Bandwidth, each vary by less
than ±5% over the industrial temperature range (see Typical
Perf ormance Curves).

Ordering Information

PART NUMBER

(BRAND)

HA3-2842-5 0 to 75 8 Ld PDIP E8.3
HA9P2842-5

(H2842F5)

TEMP.

RANGE (oC) PACKAGE

0 to 75 8 Ld SOIC M8.15

PKG.

NO.

Features

• Stable at Gains of 2 or Greater

• Low AC Variability Over Process and Temperature

• Gain Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . 80MHz

• Gain Flatness to 10MHz. . . . . . . . . . . . . . . . . . . . 0.035dB

• High Slew Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . 400V/µs

• High Output Current (Min) . . . . . . . . . . . . . . . . . . . 100mA

• Differential Gain/Phase. . . . . . . . . . . 0.02%/0.03 Degrees

• Low Supply Current (Max) . . . . . . . . . . . . . . . . . . . . 15mA

• Enhanced Replacement for AD842

Applications

• Pulse and Video Amplifiers

• Wideband Amplifiers

• Coaxial Cable Drivers

• Fast Sample-Hold Circuits

• High Frequency Signal Conditioning Circuits

Pinout

HA-2842

(PDIP, SOIC)

TOP VIEW

BAL

-IN

+IN

1
2

-

+

3
4

V-

8

BAL

7

V+

6

OUT

5

NC

1

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 321-724-7143

| Copyright © Intersil Corporation 1999

HA-2842

Absolute Maximum Ratings Thermal Information

Voltage Between V+ and V- Terminals. . . . . . . . . . . . . . . . . . . . 35V

Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V

Output Current (Notes 3, 4) . . . . . . . . . . . . . . . . . . . . . . . . . . 125mA

100mA (50% Duty Cycle)

Operating Conditions

Temperature Range

HA-2842-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC

Recommended Supply Voltage Range . . . . . . . . . . . ±6.5V to ±15V

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 150oC for plastic
packages. By using Application Note AN556 on Safe Operating Area equations, along with the packaging thermal resistances listed in the
Thermal Information section, proper load conditions can be determined.

2. θJA is measured with the component mounted on an evaluation PC board in free air.

3. VO=±5V,RLUnconnected,Dutycycle ≤ 50%. For information about usinghighoutputcurrent amplifiers, please refer to Application NoteAN556
(Thermal Safe-Operating-Areas For High Current Op Amps), and the “Power Dissipation Considerations” section in the “ApplicationInformation”
section of this datasheet.

4. Maximum continuous (100% Duty Cycle) output current is 50mA. For currents >50mA, Duty Cycle must be derated accordingly.

Thermal Resistance (Typical, Note 2) θJA (oC/W)

8 Lead PDIP Package . . . . . . . . . . . . . . . . . . . . . . . 92

8 Lead SOIC Package . . . . . . . . . . . . . . . . . . . . . . . 157

Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . . .175oC

Maximum Junction Temperature (Plastic Package, Note 1) . . . . 150oC

Maximum Storage Temperature Range. . . . . . . . . . -65oC to 150oC

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC

(SOIC - Lead Tips Only)

Electrical Specifications V

PARAMETER TEST CONDITIONS TEMP (oC)

INPUT CHARACTERISTICS

Offset Voltage (Note 10) 25 - 1 3 mV

Average Offset Voltage Drift Full - 13 - µV/oC
Bias Current (Note 10) 25 - 5 10 µA

Average Bias Current Drift Full - 20 - nA/oC
Offset Current 25 - 0.5 1.0 µA

Average Offset Current Drift Full - 1.3 - nA/oC
Input Resistance 25 - 170 - kΩ
Input Capacitance 25 - 1 - pF
Common Mode Range Full ±10 - - V
Input Noise Voltage 10Hz to 1MHz 25 - 16 - µV
Input Noise Voltage Density f = 1kHz, R
Input Noise Current (Note 10) f = 1kHz, R

TRANSFER CHARACTERISTICS

= ±15V, RL = 1kΩ, CL≤ 10pF, Unless Otherwise Specified

SUPPLY

SOURCE

SOURCE

= 0Ω 25 - 16 ­ = 100kΩ 25 - 2 -

HA-2842-5

UNITSMIN TYP MAX

Full - - 6 mV

Full - - 15 µA

Full - - 1.5 µA

nV Hz⁄

pA Hz⁄

RMS

Large Signal Voltage Gain VO = ±10V 25 50 100 - kV/V

Full 30 60 - kV/V

Common-Mode Rejection Ratio (Note 10) VCM = ±10V Full 80 110 - dB

2

HA-2842

Electrical Specifications V

PARAMETER TEST CONDITIONS TEMP (oC)

Minimum Stable Gain 25 2 - - V/V
Gain Bandwidth Product (Note 10) A
Gain Flatness to 10MHz (Note 10) RL≥ 75Ω 25 - ±0.035 - dB

OUTPUT CHARACTERISTICS

Output Voltage Swing (Note, 10) VO = ±10V Full ±10 ±11 - V
Output Current (Note 10) Note 3 Full 100 - - mA
Output Resistance 25 - 8.5 - Ω
Full Power Bandwidth (Note 6) VO = ±10V 25 5.2 6 - MHz
Differential Gain (Note 10) Note 5 25 - 0.02 - %
Differential Phase (Note 10) Note 5 25 - 0.03 - Degrees
Harmonic Distortion (Note 10) VO = 2V
TRANSIENT RESPONSE (Note 7)
Rise Time 25 - 4 - ns
Overshoot 25 - 25 - %

= ±15V, RL = 1kΩ, CL≤ 10pF, Unless Otherwise Specified (Continued)

SUPPLY

= 100 25 - 80 - MHz

VCL

, f = 1MHz, AV = 2 25 - >81 - dBc

P-P

HA-2842-5

UNITSMIN TYP MAX

Slew Rate (Notes 9, 10) AV = [phone] - V/µs
Settling Time 10V Step to 0.1% 25 - 100 - ns

POWER REQUIREMENTS

Supply Current (Note 10) 25 - 14.2 - mA

Full - 14.3 15 mA

Power Supply Rejection Ratio (Note 10) Note 8 Full 70 80 - dB

NOTES:

5. Differential gain and phase are measured with a VM700A video tester, using a NTC-7 composite VITS. RF = R1 = 1kΩ, RL = 700Ω.

6. Full Power Bandwidth guaranteed based on slew rate measurement using .

7. Refer to Test Circuits section of this data sheet.

8. V

9. This parameter is not tested. The limits are guaranteed based on lab characterization and reflect lot-to-lot variation.

10. See “Typical Performance Curves” for more information.

SUPPLY

= ±10V to ±20V.

FPBW

Slew Rate

---------------------------=

2πV

PEAK

V

; 10V=

PEAK

3