Intersil Corporation FRM450R, FRM450H, FRM450D Datasheet

June 1998

FRM450D, FRM450R,

FRM450H

10A, 500V, 0.600 Ohm, Rad Hard,

N-Channel Power MOSFETs

Features

• 10A, 500V, RDS(on) = 0.600Ω

• Second Generation Rad Hard MOSFET Results From New Design Concepts

• Gamma - Meets Pre-Rad Specifications to 100KRAD(Si)

- Defined End Point Specs at 300KRAD(Si) and 1000KRAD(Si)

- Performance Permits Limited Use to 3000KRAD(Si)

• Gamma Dot - Survives 3E9RAD(Si)/sec at 80% BVDSS Typically

- Survives 2E12 Typically If Current Limited to IDM

• Photo Current - 30nA Per-RAD(Si)/sec Typically

• Neutron - Pre-RAD Specifications for 3E12 Neutrons/cm

- Usable to 3E13 Neutrons/cm

2

2

Description

The Intersil has designed a series of SECOND GENERATION hardened power
MOSFETs of both N and P channel enhancement types with ratings from 100V to
500V, 1A to 60A, and on resistance as low as 25mΩ. Total dose hardness is
offered at 100K RAD(Si) and 1000KRAD(Si) with neutron hardness ranging from
1E13n/cm
(GAMMA DOT) exists for rates to 1E9 without current limiting and 2E12 with cur­rent limiting.

This MOSFET is an enhancement-mode silicon-gate power field effect transistor of
the vertical DMOS (VDMOS) structure. It is specially designed and processed to
exhibit minimal characteristic changes to total dose (GAMMA) and neutron (n
exposures. Design and processing efforts are also directed to enhance survival to
heavy ion (SEE) and/or dose rate (GAMMA DOT) exposure.

2

for 500V product to 1E14n/cm2 for 100V product. Dose rate hardness

Package

Symbol

o

)

TO-204AA

This part may be supplied as a die or in various packages other than shown above .
Reliability screening is available as either non TX (commercial), TX equivalent of
MIL-S-19500, TXV equivalent of MIL-S-19500, or space equivalent of
MIL-S-19500. Contact the Intersil High-Reliability Marketing group for any desired
deviations from the data sheet.

Absolute Maximum Ratings (TC = +25

Drain-Source Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VDS 500 V

Drain-Gate Voltage (RGS = 20kΩ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDGR 500 V

Continuous Drain Current

TC = +25

TC = +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ID

Pulsed Drain Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IDM 30 A

Gate-Source Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGS ±20 V

Maximum Power Dissipation

TC = +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT

TC = +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT

Derated Above +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inductive Current, Clamped, L = 100µH, (See Test Figure). . . . . . . . . . . . . . . . . . . . . . . . . . ILM 30 A

Continuous Source Current (Body Diode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IS 10 A

Pulsed Source Current (Body Diode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISM 30 A

Operating And Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJC, TSTG -55 to +150

Lead Temperature (During Soldering)

Distance > 0.063 in. (1.6mm) From Case, 10s Max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 300

o

C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ID

o

C) Unless Otherwise Specified

FRM450D, R, H UNITS

10

6

150

60

1.20

A
A

W
W

W/oC

o

C

o

C

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207

| Copyright © Intersil Corporation 1999

4-1

File Number 3236.1

FRM450D, FRM450R, FRM450H

Pre-Radiation Electrical Specifications TC = +25

o

C, Unless Otherwise Specified

LIMITS

PARAMETER SYMBOL TEST CONDITIONS

Drain-Source Breakdown Volts BVDSS VGS = 0, ID = 1mA 500 - V
Gate-Threshold Volts VGS(th) VDS = VGS, ID = 1mA 2.0 4.0 V
Gate-Body Leakage Forward IGSSF VGS = +20V - 100 nA
Gate-Body Leakage Reverse IGSSR VGS = -20V - 100 nA
Zero-Gate Voltage

Drain Current

IDSS1
IDSS2
IDSS3

VDS = 500V, VGS = 0
VDS = 400V, VGS = 0
VDS = 400V, VGS = 0, TC = +125oC

-

-

-

1

0.025

0.25
Rated Avalanche Current IAR Time = 20µs - 30 A
Drain-Source On-State Volts VDS(on) VGS = 10V, ID = 10A - 6.30 V
Drain-Source On Resistance RDS(on) VGS = 10V, ID = 6A - 0.600 Ω
Turn-On Delay Time td(on) VDD = 250V, ID = 10A - 160
Rise Time tr Pulse Width = 3µs - 260
Turn-Off Delay Time td(off) Period = 300µs, Rg = 25Ω - 750
Fall Time tf 0 ≤ VGS ≤ 10 (See Test Circuit) - 180
Gate-Charge Threshold QG(th)

Gate-Charge Total QGM 125 502

VDD =250V, ID = 10A

418

IGS1 = IGS2

Plateau Voltage VGP 3 14 V

0 ≤ VGS ≤ 20

Gate-Charge Source QGS 8 34
Gate-Charge Drain QGD 30 123
Diode Forward Voltage VSD ID = 10A, VGD = 0 0.6 1.8 V
Reverse Recovery Time TT I = 10A; di/dt = 100A/µs - 3000 ns
Junction-To-Case Rθjc - 0.83
Junction-To-Ambient Rθja Free Air Operation - 30

UNITSMIN MAX

o

mA

ns

ncGate-Charge On State QG(on) 64 258

nc

C/W

0V

VGS = 12V

ELECTRONIC SWITCH OPENS

50Ω

L

WHEN I

V

DS

V

DD

R

L

V

DS

VARY t

TO OBTAIN

DUT

R

GS

0V

P

REQUIRED PEAK I

VGS≤ 20V

t

P

CURRENT

TRANSFORMER

AS

50Ω

+

I

AS

-

DUT

IS REACHED

AS

FIGURE 1. RESISTIVE SWITCHING TEST CIRCUIT FIGURE 2. UNCLAMPED ENERGY TEST CIRCUIT

4-2

+

V

DD

-

50V-150V