Intersil Corporation FRM130R, FRM130H, FRM130D Datasheet

June 1998

FRM130D, FRM130R,

FRM130H

14A, 100V, 0.180 Ohm, Rad Hard,

N-Channel Power MOSFETs

Features

• 14A, 100V, RDS(on) = 0.180Ω

Second Generation Rad Hard MOSFET Results From New Design Concepts

•

• Gamma - Meets Pre-Rad Specifications to 100KRAD(Si)

- Defined End Point Specs at 300KRAD(Si) and 1000KRAD(Si)

- Performance Permits Limited Use to 3000KRAD(Si)

• Gamma Dot - Survives 3E9RAD(Si)/sec at 80% BVDSS Typically

- Survives 2E12 Typically If Current Limited to IDM

• Photo Current - 1.5nA Per-RAD(Si)/sec Typically

• Neutron - Pre-RAD Specifications for 3E13 Neutrons/cm

- Usable to 3E14 Neutrons/cm

2

2

Description

The Intersil Corporation has designed a series of SECOND GENERATION hard­ened power MOSFETs of both N and P channel enhancement types with ratings
from 100V to 500V, 1A to 60A, and on resistance as low as 25mΩ. Total dose
hardness is offered at 100K RAD(Si) and 1000KRAD(Si) with neutron hardness
ranging from 1E13n/cm
rate hardness (GAMMA DOT) exists for rates to 1E9 without current limiting and
2E12 with current limiting.

This MOSFET is an enhancement-mode silicon-gate power field effect transistor of
the vertical DMOS (VDMOS) structure. It is specially designed and processed to
exhibit minimal characteristic changes to total dose (GAMMA) and neutron (n
exposures. Design and processing efforts are also directed to enhance survival to
heavy ion (SEE) and/or dose rate (GAMMA DOT) exposure.

2

for 500V product to 1E14n/cm2 for 100V product. Dose

Package

Symbol

o

)

TO-204AA

This part may be supplied as a die or in various packages other than shown above .
Reliability screening is available as either non TX (commercial), TX equivalent of
MIL-S-19500, TXV equivalent of MIL-S-19500, or space equivalent of
MIL-S-19500. Contact the Intersil High-Reliability Marketing group for any desired
deviations from the data sheet.

Absolute Maximum Ratings (TC = +25

Drain-Source Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VDS 100 V

Drain-Gate Voltage (RGS = 20kΩ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDGR 100 V

Continuous Drain Current

TC = +25

TC = +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ID

Pulsed Drain Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IDM 42 A

Gate-Source Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .VGS ±20 V

Maximum Power Dissipation

TC = +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT

TC = +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PT

Derated Above +25oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inductive Current, Clamped, L = 100µH, (See Test Figure). . . . . . . . . . . . . . . . . . . . . . . . . . ILM 42 A

Continuous Source Current (Body Diode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IS 14 A

Pulsed Source Current (Body Diode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISM 42 A

Operating And Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TJC, TSTG -55 to +150

Lead Temperature (During Soldering)

Distance > 0.063 in. (1.6mm) From Case, 10s Max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TL 300

o

C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ID

o

C) Unless Otherwise Specified

FRM130D, R, H UNITS

14

9

75
30

0.60

A
A

W
W

W/oC

o

C

o

C

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207

| Copyright © Intersil Corporation 1999

4-1

File Number 3217.1

FRM130D, FRM130R, FRM130H

Pre-Radiation Electrical Specifications TC = +25

o

C, Unless Otherwise Specified

LIMITS

PARAMETER SYMBOL TEST CONDITIONS

Drain-Source Breakdown Volts BVDSS VGS = 0, ID = 1mA 100 - V
Gate-Threshold Volts VGS(th) VDS = VGS, ID = 1mA 2.0 4.0 V
Gate-Body Leakage Forward IGSSF VGS = +20V - 100 nA
Gate-Body Leakage Reverse IGSSR VGS = -20V - 100 nA
Zero-Gate Voltage

Drain Current

IDSS1
IDSS2
IDSS3

VDS = 100V, VGS = 0
VDS = 80V, VGS = 0
VDS = 80V, VGS = 0, TC = +125oC

-

-

-

1

0.025

0.25
Rated Avalanche Current IAR Time = 20µs - 42 A
Drain-Source On-State Volts VDS(on) VGS = 10V, ID = 14A - 2.65 V
Drain-Source On Resistance RDS(on) VGS = 10V, ID = 9A - .18 Ω
Turn-On Delay Time td(on) VDD = 50V, ID = 14A - 30
Rise Time tr Pulse Width = 3µs - 218
Turn-Off Delay Time td(off) Period = 300µs, Rg = 25Ω - 156
Fall Time tf 0 ≤ VGS ≤ 10 (See Test Circuit) - 144
Gate-Charge Threshold QG(th)

Gate-Charge Total QGM 36 146

VDD = 50V, ID = 14A

14

IGS1 = IGS2

Plateau Voltage VGP 3 14 V

0 ≤ VGS ≤ 20

Gate-Charge Source QGS 3 14
Gate-Charge Drain QGD 9 36
Diode Forward Voltage VSD ID = 14A, VGD = 0 0.6 1.8 V
Reverse Recovery Time TT I = 14A; di/dt = 100A/µs - 800 ns
Junction-To-Case Rθjc - 1.67
Junction-To-Ambient Rθja Free Air Operation - 60

UNITSMIN MAX

o

mA

ns

ncGate-Charge On State QG(on) 18 74

nc

C/W

0V

VGS = 12V

ELECTRONIC SWITCH OPENS

50Ω

L

WHEN I

V

DS

V

DD

R

L

V

DS

VARY t

TO OBTAIN

DUT

R

GS

0V

P

REQUIRED PEAK I

VGS≤ 20V

t

P

CURRENT

TRANSFORMER

AS

50Ω

+

I

AS

-

DUT

IS REACHED

AS

FIGURE 1. RESISTIVE SWITCHING TEST CIRCUIT FIGURE 2. UNCLAMPED ENERGY TEST CIRCUIT

4-2

+

V

DD

-

50V-150V