Intersil Corporation CD54ACT541F3A, CD54AC541F3A Datasheet

July 1998

CD54AC541F3A,

SEMICONDUCTOR

CD54ACT541F3A

Octal Buffer/Line Driver

Three-State, Non-Inverting

Features

• This Circuit is Processed in Accordance to MIL-STD­883 and is Fully Conformant Under the Provisions of
Paragraph 1.2.1.

• Exceeds 2kV ESD Protection MIL-STD-883, Method 3015

• Meets JEDEC Standard No. 20

• SCR - Latch-Up-Resistant CMOS Process and Circuit
Design

• Speed of Bipolar FAST/A/S with Significantly Reduced
Power Consumption

• Functionally and Pin-Compatible with Industry 54
Bipolar Types in the FAST, AS and S Series

• Balanced Propagation Delays

• Military Operating Temperature Range

- Ceramic (CERDIP) 54 Series: . . . . . . . . -55 to 125

o

• ±24mA Output Drive Current, Drives 75Ω Lines with­out Need for Terminations

• Fan Out (Over Temperature)

- ACL Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2400

- FAST Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

- AS Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

• Operating Voltage

- AC Types. . . . . . . . . . . . . . . . . . . . . . . . . .1.5V to 5.5V

- ACT Types. . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V

Functional Diagram

A0

A1

A2

A3

A4

A5

A6

A7

2

3

4

5

6

7

8

9

18

Y0

17

Y1

16

Y2

15

Y3

14

Y4

13

Y5

12

Y6

11

Y7

Description

The CD54AC541F3A and CD54ACT541F3A are octal
buffer/line drivers that utilize the Harris Advanced CMOS
Logic technology. The CD54AC541F3A and
CD54ACT541F3A are non-inverting three-state buffershaving
two active-LOW output enab les.

Ordering Information

TEMP.

PART NUMBER

CD54AC541F3A -55 to 125 20 Ld CERDIP F20.3
CD54ACT541F3A -55 to 125 20 Ld CERDIP F20.3

NOTE:

1. Waf erand die forthis part number is availablewhich meets all elec­trical specifications. Please contact your local sales office or Harris
customer service for ordering information.

RANGE (oC) PACKAGE

C

Pinout

OE

A0
A1
A2
A3
A4
A5
A6
A7

GND

1

1

2
3
4
5
6
7
8
9

10

V

20

CC

OE

19

2

Y0

18

Y1

17

Y2

16

Y3

15

Y4

14

Y5

13
12

Y6
Y7

11

PKG.

NO.

OE

1

OE

2

CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright

© Harris Corporation 1998

1

19

GND = 10
V

= 20

CC

1

File Number 3914.1

CD54AC541F3A, CD54ACT541F3A

Absolute Maximum Ratings Thermal Information

DC Supply Voltage, VCC. . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6V

DC Input Diode Current, I

IK

For VI < -0.5V or VI > VCC + 0.5V. . . . . . . . . . . . . . . . . . . . . .±20mA

DC Output Diode Current, I

OK

For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±50mA

DC Output Source or Sink Current per Output Pin, I

O

For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±50mA

DC VCC or Ground Current, I

CC orIGND

(Note 2) . . . . . . . . .±100mA

Operating Conditions

Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC

Supply Voltage Range, VCC (Note 3)

AC Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5V to 5.5V

ACT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V

DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to V

Input Rise and Fall Slew Rate, dt/dv

AC Types

1.5V to 3V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50ns (Max)

3.6V to 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20ns (Max)

4.5V to 5.5V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10ns (Max)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTES:

2. For up to 4 outputs per device, add ±25mA for each additional output.

3. Unless otherwise specified, all voltages are referenced to ground.

4. θJA is measured with the component mounted on an evaluation PC board in free air.

Thermal Resistance (Typical, Note 4) θJA (oC/W) θJC (oC/W)

CERDIP Package . . . . . . . . . . . . . . . . 85 24

Maximum Junction Temperature (Hermetic P ac kage or Die) . . . 175oC

Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC

Maximum Lead Temperature (Soldering 10s). . . . . . . . . . . . . 300oC

CC

DC Electrical Specifications

PARAMETER SYMBOL

AC TYPES

High Level Input Voltage V

Low Level Input Voltage V

High Level Output Voltage V

IH

IL

OH

TEST

CONDITIONS

(V) IO(mA) MIN MAX MIN MAX

I

V

CC

(V)

o

C -55oC TO 125oC

25

- - 1.5 1.2 - 1.2 - V
3 2.1 - 2.1 - V

4.5 3.15
(Note 5)

- 3.15
(Note 5)

-V

5.5 3.85 - 3.85 - V

- - 1.5 - 0.3 - 0.3 V
3 - 0.9 - 0.9 V

4.5 - 1.35
(Note 5)

- 1.35
(Note 5)

5.5 - 1.65 - 1.65 V

VIH or V

-0.05 1.5 1.4 - 1.4 - V

IL

-0.05 3 2.9 - 2.9 - V

-0.05 4.5 4.4 - 4.4 - V

-4 3 2.58 - 2.4 - V

-24 4.5 3.94
(Note 5)

-50

5.5 - - 3.85 - V

- 3.7
(Note 5)

-V

(Note 6, 7)

UNITSV

V

2