intersil 5962-0620705Q3A, 5962-0620706Q3A, 5962-0620707Q2A, 5962-0620708Q2A Data Sheet
®
http://www.BDTIC.com/Intersil
5962-0620705Q3A, 5962-0620706Q3A,
5962-0620707Q2A, 5962-0620708Q2A
Data Sheet May 31, 2006
±15kV ESD Protected, +5.0V 1Microamp,
250kbps, RS-232 Transmitters/Receivers
The Intersil 5962-062070xQxA devices are 5.0V powered
RS-232 transmitters/receivers which meet ElA/TIA-232 and
V.28/V.24 specifications. Additionally, they provide ±15kV
ESD protection (IEC61000-4-2 Air Gap and MIL-STD 883
Human Body Model) on transmitter outputs and receiver
inputs (RS-232 pins). Targeted applications include
ruggedized portable products and remotely deployed
devices exposed to extreme temperature and humidity
where the low operational and even lower standby, power
consumption is critical. Efficient on-chip charge pumps,
coupled with manual and automatic power-down functions
(except for the 5962-0620707Q2A), reduce the standby
supply current to a 1µA trickle. Small footprint packaging and
the use of small, low value capacitors ensure board space
savings as well. Data rates greater than 250kbps are
guaranteed at worst case load conditions. This family is fully
compatible with 5.0V-only systems.
Specifications for QML devices are controlled by the
Defense Supply Center in Columbus (DSCC). The SMD
numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-06207. A “hot-link” is provided
on our website for downloading.
FN6298.0
Features
• Meets EIA/TIA-232 and V.28/V.24 Specifications at 5V
• Electrically Screened to DSCC SMD#5962-06207
• QML Qualified per MIL-PRF-38535 Requirements
• SMD Compliance
• Military Temperature Range
• Latch-up Free
• Hermetic Package
• ESD Protection for RS-232 I/O Pins to ±15kV (IEC61000)
• Guaranteed Mouse Driveability (ICL3243E)
• Requires Single +5.0V ±10% Power Supply
• Receiver Hysteresis for Improved Noise Immunity
• Low Power Automatic Power-down Modes
(Except for ICL3232E) . . . . . . . . . . . . . . . . . . . . . . . . .1µA
• Guaranteed Minimum 250kbps Data Rate
• Manual and Automatic Power-down Features
• Multiple Drivers/Receivers
• On-Chip Voltage Converters Require Only Four External
Capacitors
• Regulated Dual Charge Pumps
Ordering Information
DESC P/N CONFIGURATION TEMP (°C) PACKAGE
5962-0620705Q3A ICL3243E 3D/5R -55 to +125 28 Ld CLCC
5962-0620706Q3A ICL3238E 5D/3R -55 to +125 28 Ld CLCC
5962-0620707Q2A ICL3232E 2D/2R -55 to +125 20 Ld CLCC
5962-0620708Q2A ICL3221E 1D/1R -55 to +125 20 Ld CLCC
Applications
• Any Military or High-Rel System Requiring RS-232
Communication Ports
- Battery Powered, Hand-Held, and Portable Equipment
- Ruggedized Handheld GPS, Laptop Computers,
Notebooks, Palmtops
- Industrial Control/Shop Floor Communications
- Field Deployed Sensors/Devices Exposed to Extreme
Temperature/Humidity
- Ruggedized Cellular/Mobile Phones
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
All other trademarks mentioned are the property of their respective owners.
Copyright Intersil Americas Inc. 2006. All Rights Reserved
Pinouts
http://www.BDTIC.com/Intersil
5962-0620705Q3A, 5962-0620706Q3A, 5962-0620707Q2A, 5962-0620708Q2A
C1-
C2+
C2-
NC
4
5
6
V-
7
8
ICL3221E (CLCC)
TOP VIEW
EN
C1+
V+
3
9101112
IN
R1
FORCEOFF
220119
13
IN
OUT
T1
R1
INVALID
VCC
18
17
16
15
14
NC
NC
GND
T1OUT
NC
FORCEON
C1-
C2+
C2-
NC
4
5
6
V-
7
8
ICL3232E (CLCC)
TOP VIEW
C1+
V+
VCC
R2
GND
13
IN
NC
OUT
T2
NC
3
220119
9101112
IN
OUT
R2
T2
NC
18
T1
17
OUT
R1
16
IN
R1
15
OUT
14
T1
IN
T
T
T
R
2 IN
R
3 IN
R
4 IN
R
5 IN
1 OUT
2 OUT
3 OUT
5
6
7
8
9
10
11
ICL3243E (CLCC)
1 IN
R
V-
3 2 14
14 15 16 17 1812 13
3 INT2 INT1 IN
T
TOP VIEW
C2+
C2-
5 OUT
R
+
1
V+
C
28 27 26
4 OUTR3 OUTR2 OUT
R
VCC
25
24
23
22
21
20
19
GND
C1-
FORCEON
FORCEOFF
INVALID
R
2OUTB
R
1 OUT
T1 OUT
T2 OUT
T3 OUT
R1 IN
R2 IN
T4 OUT
R3 IN
ICL3238E (CLCC)
TOP VIEW
V-
5
6
7
8
9
10
11
T5 OUT
GND
C2-
3 2 14
14 15 16 17 1812 13
FORCEON
FORCEOFF
C1+
C2+
28 27 26
INVALID
R1OUTB
V+
T5 IN
VCC
25
24
23
22
21
20
19
R3 OUT
C1-
T1 IN
T2 IN
T3 IN
R1 OUT
R2 OUT
T4 IN
2
FN6298.0
May 31, 2006
5962-0620705Q3A, 5962-0620706Q3A, 5962-0620707Q2A, 5962-0620708Q2A
http://www.BDTIC.com/Intersil
Pin Descriptions
PIN FUNCTION
V
CC
V+ Internally generated positive transmitter supply.
V- Internally generated negative transmitter supply.
GND Ground connection.
C1+ External capacitor (voltage doubler) is connected to this lead.
C1- External capacitor (voltage doubler) is connected to this lead.
C2+ External capacitor (voltage inverter) is connected to this lead.
C2- External capacitor (voltage inverter) is connected to this lead.
T
IN
T
OUT
R
IN
R
OUT
R
OUTB
INVALID
EN
FORCEOFF
System power supply input (4.5V to 5.5V).
TTL/CMOS compatible transmitter Inputs. (Note 1)
±15kV ESD Protected, RS-232 level (nominally ±5.5V) transmitter outputs.
±15kV ESD Protected, RS-232 compatible receiver inputs.
TTL/CMOS level receiver outputs.
TTL/CMOS level, noninverting, always enabled receiver outputs.
Active low output that indicates if no valid RS-232 levels are present on any receiver input.
Active low receiver enable control.
Active low control to shut down transmitters and on-chip power supply. This overrides any automatic circuitry and FORCEON
(See Tables 1 & 2, Note 1).
FORCEON Active high input to override automatic power-down circuitry thereby keeping transmitters active. (FORCEOFF
Note 1).
NOTE:
1. The ICL3238E input pins incorporate positive feedback resistors. Once the input is driven to a valid logic level, the feedback resistor maintains
that logic level until V
RCVR OR
XMTR
EDGE
WITHIN 30
SEC?
ICL3238E
No H H Active Active Active No L Normal Operation (Enhanced
No H H Active Active Active Yes H
Yes H L Active Active Active No L Normal Operation (Enhanced
Yes H L Active Active Active Yes H
No H L High-Z Active Active No L Power-down Due to Enhanced
No H L High-Z Active Active Yes H
FORCEOFF
INPUT
is removed. Unused transmitter inputs may be left unconnected by the user.
CC
TABLE 1. POWER-DOWN LOGIC TRUTH TABLE
RS-232
LEVEL
PRESENT
FORCEON
INPUT
TRANSMITTER
OUTPUTS
RECEIVER
OUTPUTS
R
OUTB
OUTPUT
AT
RECEIVER
INPUT?
INVALID
OUTPUT MODE OF OPERATION
Auto Power-down Disabled)
Auto Power-down Enabled)
Auto Power-down Logic
must be high,
X L X High-Z High-Z Active No L Manual Power-down
X L X High-Z High-Z Active Yes H
3
FN6298.0
May 31, 2006
Loading...