Interquartz AS280, AS180 User Manual

Download

Page 1

Gigaset AS180/AS280

The handset at a glance

1 Charge status of

the batteries 2Display keys 3Message key

Flashes: new messages

received 4 AS180:

h Directory key

AS280:

d Handsfree key

5 Control key (u) 6Talk key 7 AS280:

h Directory key

(press down) 8 End call and

On/Off key 9Ringer on/off

(press and hold

in idle status)

10 Keypad lock on/off

(press and hold)

11 Recall key

- Consultation call

(flash)

- Dialling pause

(press and hold)

12 Microphone 13 "Microphone off" key

9 10 11

12 13

3 4 5 6

7 8

11. 12 . 11: 56 INT MENU

Display keys on handset:

Pressing a key launches the function that appears above that key in the display.

Display icon

INT

Function when pressed

Call other registered handsets

¢ page 9.

“ U

Open main/submenu (see Menu tree

Go back one menu level. Scroll up/down or adjust

volume with u. Move cursor to left/right

with u. Backspace deletes one charac-

ter at a time from right to left. Confirm menu function or save entry.

¢ page 13).

The base station at a glance

AS180/AS280 base station

Registration/paging key: Search for handsets (press briefly, "Paging" Register handsets (press and hold

¢ page 9).

¢ page 9)

Page 2

Safety precautions

Read this user guide and the safety precautions carefully before use. Explain their content and the potential haz ards associated with using the telephone to your children.

Only use the mains adapter supplied.

Fit only the recommended, rechargeable batteries (¢ page 11), i.e. never use any

other battery type or non-rechargeable batteries as this could result in significant health risks and personal injury.

The operation of medical appliances may be affected. Be aware of the technical conditions in

your particular environment, e.g. doctor's

surgery. Do not hold the rear of the handset to your ear

when it is ringing. Otherwise you risk serious and permanent damage to your hearing. The handset may cause an unpleasant humming noise in hearing aids.

Do not install the phone in a bathroom or shower room. The handset and base station are

not splashproof.

Do not use your phone in environments with a potential explosion hazard, e.g. paint shops.

If you give your Gigaset to someone else, make sure you also give them the user guide.

Please remove faulty base stations from use or have them repaired by Service, as they could interfere with other wireless services.

Disposal

Batteries should not be disposed of in general household waste. Observe the local waste dis posal regulations, details of which can be obtained from your local authority or the dealer you purchased the product from. All electrical and electronic equipment must be disposed of separately from general household waste using the sites designated by local authorities. If a product displays this symbol of a crossed-out rubbish bin, the product is subject to European Directive 2002/96/EC. The appropriate disposal and separate collection of used equipment serve to prevent potential harm to the environment and to health. They are a precondition for the re-use and recy cling of used electrical and electronic equipment. For further information on disposing of your used equipment, please contact your local authority, your refuse collection service or the dealer you purchased the product from.

Emergency numbers cannot be dialled if the keypad lock (¢ page 1) is activated! Not all of the functions described in this user guide are available in all countries.

Care

Wipe the base station, charging cradle and handset

with a damp cloth (do not use solvent) or an anti static cloth. Never use a dry cloth. This can cause static.

Contact with liquid

If the handset has come into contact with liquid:

◆ Switch off the handset and remove the bat-

tery pack immediately.

◆ Allow the liquid to drain from the handset.

◆ Pat all parts dry, then place the handset with

the battery compartment open and the keypad facing down in a dry, warm place for at least

hours (not in a microwave, oven etc.).

◆ Do not switch on the handset again until it is

completely dry.

When it has fully dried out, you will normally be able to use it again.

ECO DECT

You are helping to protect the environment with your Gigaset AS180/AS280.

Reduced energy consumption

Your telephone has a power-saving adapter plug and uses less power.

Reduced transmission power

The transmission power of your telephone is reduced automatically:

The handset's transmission power is reduced

depending on the distance to the base station. The transmission power on the base station is reduced to virtually zero when only one handset is registered and the handset is in the base sta tion.

You can reduce the transmission power of the handset and base station even more by using Eco Mode/Eco Mode+ (see Menu tree

¢ page 14):

◆ Eco Mode: 80% transmission power reduc-

tion in standby mode and during a call (the range of the base station is reduced).

◆ Eco Mode+: 100% transmission power deac-

tivation in standby mode (top left display icon

½). Press and hold the talk key c to check

that the base station can be reached. You will hear the ringing tone if the base station can be reached.

Page 3

First steps

Check the pack contents

◆ one Gigaset AS180/AS280 base station,

◆ one mains adapter,

◆ one Gigaset AS18H/AS28H handset,

◆ one phone cord,

◆ two batteries,

◆ one battery cover,

◆ one user guide.

If you have purchased a model with multiple handsets, the package should contain two batteries, a battery cover and a charging cradle with mains adapter for each additional handset.

Setting up the base station and charging cradle (if included)

The base station and charging cradle are designed for use in enclosed dry rooms with a temperature range of +5°C to +45°C.

¤ Set up the base station at a central location on a flat, non-slip surface in your house or

apartment.

Please note

Pay attention to the range of the base station. This is up to 300 m in unobstructed outdoor areas and up to 50 m inside buildings. The range is reduced when Eco Mode (

The phone's feet do not usually leave any marks on surfaces. However, due to the multitude of different varnishes and polishes used on today's furnishings, the occurrence of marks on the surfaces cannot be completely ruled out. You can also mount the base station and charging cradle on the wall.

Please note:

◆ Never expose the telephone to the influence of heat sources, direct sunlight or other

electrical devices.

◆ Protect your Gigaset from moisture, dust, corrosive liquids and vapours.

¢ page 14) is activated.

Connecting the base station

¤ First connect the mains adapter 1. ¤ Then connect the telephone jack 2

and insert the cables into the cable ducts.

Please note:

◆ The mains adapter must always be

connected, as the phone will not

operate without mains connection.

◆ Only use the mains adapter and

phone

cord supplied. Pin connections

on telephone cables can vary.

Page 4

Connecting the charging cradle (if included)

¤ Connect the flat plug from the power supply 1. ¤ Plug the mains adapter into the plug socket 2.

If you need to disconnect the plug from the charging cradle, press the release button 1 and disconnect the plug 2.

Setting up the handset for use

The display is protected by a plastic film.

Please remove the protective film!

Inserting the batteries and closing the battery cover

Warning

Use only the rechargeable batteries (¢ page 11) recommended by Gigaset Commu- nications GmbH*. Never use conventional (non-rechargeable) batteries, as this could result in significant health risks and damage to property. For example, the outer casing of the batteries could be destroyed or the batteries could explode. The phone could also malfunction or be damaged as a result of using batteries that are not of the recommended type.

*Gigaset ommunications GmbH is a trademark licensee of Siemens AGC

Page 5

¤ Insert the batteries the right

way round. The polarity is indicated in/on the battery compartment.

¤ Slide the battery cover back into the

main casing until it clicks into place.

If you need to open the battery cover,

or instance to replace the batteries, place your fingertip in the grooved area on the top of the cover and slide down.

Placing the handset in the base station and registering

Put into base

Before you can use the phone, you must first register the handset to the base station.

–

¤ Place the handset with

the display facing up in the base station.

Registering

INT MENU

If you have purchased a model with multiple handsets, repeat the registration process for each individual handset. Handsets are assigned the lowest available internal number (1–4). If more than one handset is registered to the base station, the internal handset

The handset registers automatically. Registration can take up to 5 minutes.

Do not remove the handset from the base station during this time.

After successful registration, the idle screen is displayed. Charge status of the batteries:

–

= e V U (flat to full)

–

= flashes: batteries almost flat

–

e V U flashes: charging

Page 6

number appears in the top left of the display, e.g. 2. If the internal numbers 1–4 are already assigned to other devices, number

Please note

◆ Each key press interrupts the automatic registration.

◆ If automatic registration does not work, the handset will have to be registered

manually

◆ Only place the handset in the base station or charging cradle that is intended for

it.

(¢ page 9).

4 will be overwritten.

Initial charging and discharging of the batteries

The correct charge level can only be displayed if the batteries are first fully charged and discharged.

¤ Place the handset in the base station or charging cradle for

eight hours.

8 h

◆ After the first battery charge and discharge you may replace your handset in the

base station or charging cradle after every call.

◆ Always repeat the charging and discharging procedure if you remove the batteries

from the handset and reinsert them.

◆ The batteries may warm up during charging. This is not dangerous.

◆ After a while, the charge capacity of the batteries will decrease for technical rea-

sons.

¤ Then remove the handset from the base station or charging cradle

and do not replace it until the batteries are fully discharged.

Please note

Setting the date and time

Set the date and time so that the correct date and time can be assigned to incoming calls, and so that the alarm can be used.

MENU ¢ Settings ¢ OK ¢ Date/Time ¢ OK ¢ Date: ¢ ~ (enter the day, month and year in 6-digit format) ¢ OK ¢ Time: ¢ ~ (enter hours and minutes in 4-digit format) ¢ OK (display message: Saved) ¢ a (press and hold to return to idle status)

Please note

When entering the time and date, you can move the position of an entry to the left or right by pressing the control button up or down.

Display in idle status

Once the phone is registered and the time set, the idle display is shown as in this example.

Activating/deactivating the handset

Press and hold the end call key a to activate or deactivate the handset. If you place a deactivated handset in the base station or charging cradle, it will automatically activate.

Your phone is now ready for use!

If you have any questions about using your phone, please read the tips on troubleshooting ("

Questions and answers" ¢ page 11) or contact our Customer Care team ¢ page 12.

11.12. 11:56

INT MENU

Page 7

Making calls

Making external calls and ending calls

External calls are calls using the public telephone network.

(Enter the phone number) ¢c.

The phone number is dialled. (Or you can first press and hold number.) During the call you can adjust the ear piece volume using t and set the volume with u.

End the call/cancel dialling:

Press the end call key a. You can automatically insert a network provider dialling code before any phone number (see Menu tree "Preselection"

c [dial tone] and then enter the

¢ page 14).

Accepting a call

The handset indicates an incoming call by ringing and by a display on the screen.

Press the talk key c to accept the call. When Auto Answer is activated (see Menu tree

¢ page 14), simply remove the handset from the

base station/charging cradle. In idle status, use t to activate the menu for setting the call volume and use u to set the volume.

Calling Line Identification

When you receive a call, the caller's number will be displayed on your handset; the caller's name will be displayed if it is stored in the directory.

Requirements:

1 You have asked your network provider for the

caller's number ( handset screen.

2 The caller has asked the network provider for

his number to be identified (CLI).

not

Withheld appears if the caller has withheld CLI, and Unavailable appears if CLI has not been requested.

appears in the display if you have

requested Calling Line Identification,

Switch to mute

You can mute your handset when making external calls. Your caller can no longer hear you. Press the "Microphone off" key m during the call to activate/deactivate the function.

CLIP) to be displayed on your

Handsfree talking (AS280 only)

To activate while dialling:

Enter the number ~ and press the handsfree key

Switching between earpiece and handsfree mode:

During a call and when listening to the answer machine (AS285 only), press the handsfree key to activate or deactivate handsfree talking. During a call, use t to activate the menu for setting the handsfree volume and use u to set the volume.

Using the directory and lists

Last number redial list

This list contains the ten last dialled numbers.

Dialling from the last number redial list c (press briefly) ¢ u (select entry) ¢ c

Managing entries in the last number redial list c (press briefly) ¢ u (select entry) ¢ MENU

You can select the following settings:

Use Number

Copy to Dir.

Delete Entry

Delete List

Edit or add to the number. Then

dial or select other

functions from the

Copy an entry to the directory.

Delete selected entry.

Delete all entries.

MENU.

Calls list/voicemail (network mailbox) list

An advisory tone sounds and the message key flashes as soo n as a new entry appears in the calls

list/voicemail list. A message appears in the dis play.

When you press the f key, all the lists are displayed. If only one list contains new messages, this

will be opened automatically.

Please note:

If calls are saved in the network mailbox, you will receive a message if the appropriate settings have been set (depending on your network provider).

Calls list

Precondition: CLIP (¢ page 7) Depending on the type of list set, the calls list con-

tains (¢ page 14)

◆ answered calls

◆ missed calls

Depending on the type of list set, all numbers of the last 25 incoming calls are saved or just the missed calls are saved.

The calls list is displayed as follows:

CallsList 01+02

Number of new entries + number of old, read entries

Open the calls list

f ¢ CallsList 01+02 ¢ OK

The last incoming call is displayed. If necessary, use u to select another entry.

Using other functions

u (select entry) ¢ MENU

The following functions can be selected with u:

Delete Entry

Copy to Dir.

Date/Time

Status

Delete List

Delete current entry.

Copy an entry to the directory.

Call date and time (if set).

New Call: new missed call. Old Call: entry already read. Answ.: call taken.

Warning! All old and new entries will be deleted.

Calling back a caller from the calls list

f ¢ CallsList 01+02 ¢ OK ¢ u (select entry)

¢ c

Page 9

Assigning key 1 for fast access to the network mailbox

Simply press and hold key 1 on the handset and you will be connected directly to the network mail box. See Menu tree ¢ page 13.

Locating a handset ("paging")

You can locate your handset using the base station.

◆ Briefly press the registration/paging key on the

base station

◆ All handsets will ring simultaneously ("pag-

ing"), even if the ringer tones are deactivated.

End paging: briefly press the registration/paging key on the base station talk key c on a handset.

(¢ page 1).

(¢ page 1) or the

Registering handsets

You can register up to four handsets on your base station (Gigaset AS18H/AS28H) recommended).

Please note: Each additional handset must be registered on

the base station in order for it to work properly!

For automatic registration of handsets to Gigaset

AS180/AS280 ¢ page 5.

Manual registration of handsets to Gigaset AS180/ AS280

1. On the handset: MENU ¢ Settings ¢ OK

¢ Handset ¢ OK ¢ Register HS ¢ OK ¢ Enter the

system PIN of the base station (default is 0000)

¢ OK.

Registering flashes in the display.

2. On the base station: within 60 seconds of entering the system PIN, press and hold the regis tration/paging key (¢ page 1) (min. 3 seconds).

Registration takes approx. 1 minute.

De-registering handsets

Handsets can only be de-registered by resetting the base station to its default settings. This will also reset other settings

If you have only registered handsets for other GAPcompatible devices, these can only be de-regis tered with a hardware reset ¢ page 10.

¢ page 10.

Using several handsets

Making internal calls

Internal calls are free calls to other handsets that are registered to the same base station.

To make a call to other handsets, press

◆ INT ¢ ~ (1...4, enter internal number of the

handset), the handset is called or

◆ INT ¢ star key P, all handsets are called.

When a participant answers you can speak to them. To end the call, press the end call key

Internal consultation call/connecting a call

You are in conversation with an external participant. Press the INT key and call one or all handsets. The external participant hears the hold music.

◆ Before the internal participant has answered,

press the end call key the participant who answers the call.

◆ After the internal participant has answered,

you can talk to him. Press the end call key the call is diverted, or press the display key you are reconnected to the external participant.

Listening in to an external call

You are conducting an external call. An internal participant can listen in on this call and take part in the conversation (conference).

Precondition: The Listening in function must be activated.

Activating/deactivating listening in

MENU ¢ Settings ¢ OK ¢ Base ¢ OK ¢ Listening in ¢ OK (‰ = on)

Internal listening in (conference)

You want to listen in to an existing external call. Press and hold the c key. You can listen in to the call. All participants hear a signal tone. To e nd : press the end call key a. All participants hear a signal tone. If the first internal participant presses the end call key

a, the handset that has "listened in" remains

connected to the external participant.

a; the call is diverted to

”;

Page 10

Setting the alarm clock

Activating/deactivating the alarm clock

MENU ¢ Alarm Clock ¢ OK ¢ Activation

¢ OK (‰ = on)

When activated:

¢ Set the wake-up time ¢ OK

When the alarm clock rings, press any key to switch it off for 24 wake-up icon wake-up time will be displayed instead of the date.

hours. If the alarm clock is set, the

l will appear on the screen and the

Setting the wake-up time

MENU ¢ Alarm Clock ¢ OK ¢ Wake-up time ¢ OK

Enter the wake-up time in hours and minutes, then press

OK.

Phone settings

For details on how to set audio settings, see Menu tree

¢ page 13.

For details on how to set the system PIN on the base station, see the Menu tree

¢ page 14.

Changing the display language

MENU ¢ Settings ¢ OK ¢ Handset ¢ OK

¢ Language ¢ OK ¢ select the language ¢ OK

The current language is indicated by ‰ .

If you accidentally choose a language you do not understand:

MENU ¢ 4 2 1 (press the keys one after the other)

Select the correct language with u and press OK.

Resetting the handset

You can reset individual settings and changes that you have made. Entries in the directory, the calls list and the handset's registration to the base sta tion will be retained.

MENU ¢ Settings ¢ OK ¢ Handset ¢ OK ¢ Reset Handset ¢ OK

Cancel the reset with a.

Restoring the base station to the factory settings

When restoring factory settings:

◆ All handsets are de-registered

◆ Individual settings are reset

◆ All lists are deleted

◆ The system PIN is reset to the original code

0000

Only the date and time are retained.

Software reset

MENU ¢ Settings ¢ OK ¢ Base ¢ OK ¢ Base Reset ¢ OK

Hardware reset

Disconnect the power cord from the base station. Hold down the registration/paging key (¢ page 1) on the base station while reconnecting the power cable to the base station. Release the key after approximately 5 seconds.

Repeater mode

With a repeater you can increase the range of your base station. You will need to activate repeater mode

(¢ page 14). Repeater mode and Eco mode

or Eco mode+ (¢ page 1) cancel each other out.

Operating the base station on

PABX

the

The following settings are only necessary if your PABX requires them, see the user guide for your PABX.

When entering the digits, enter them slowly one after the other.

Changing the dialling mode

MENU ¢ 4 I O 1 1 ¢ The number for the set dial-

ling mode flashes: 0 = touch tone dialling (DTMF); 1 = dial pulsing (DP) ¢ enter number ¢OK.

Setting recall

MENU ¢ 4 I O 1 2 ¢ The number for the current

recall flash

3 = 400 ms; 4 = 250 ms; 5 = 300 ms; 6 = 600 ms; 7 = 800 ms ¢ enter number ¢ OK.

es: 0 = 80 ms; 1 = 100 ms; 2 = 120 ms;

Changing pause after line seizure

You can set the length of the pause inserted

between pressing the talk key

phone number.

MENU ¢ 4 I O 1 O ¢ The number for the current pause length flashes: 1 = 1 sec.; 2 = 3 sec.; 3 = 7 sec.

c and sending the

¢ enter number ¢ OK.

Changing the pause after the recall key

MENU ¢ 4 I O 1 4 ¢ The number for the current

pause length flashes: 1 = 800 ms; 2 = 1600 ms; 3 = 3200 ms ¢ enter number ¢ OK.

Page 11

Appendix

Entering letters/characters

Press the relevant key the number of times indicated. Briefly press the hash key # to switch from "Abc" to "123" mode, from "123" to "abc" mode and from "abc" to "Abc" mode.

Standard characters

1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 11x 12x 13x 14x

1 £ $ ¥ ¤

a b c 2 ä á à â ã ç

d e f 3 ë é è ê

g h i 4 ï í ì î

j k l 5

m n o 6 ö ñ ó ò ô õ

p q r s 7 ß

t u v 8 ü ú ù û

w x y z 9 ÿ ý æ ø å

. , ? ! 0 + - : ¿ ¡ " ’ ; _

* / ( ) < = > %

Abc

123

-->

# @ \ & §

1) Space

Specifications

Recommended batteries

Technology: Nickel-metal-hydride (NiMH) Size: AAA (Micro, HR03) Voltage: 1.2 V Capacity: 400–800 mAh

We recommend the following types of battery:

◆ GP 550/700 mAh

◆ Yuasa Phone 700/800 mAh

◆ Peacebay 550/650 mAh

(Valid at the time of going to press) The handset is supplied with recommended batteries.

Base station power consumption

In standby mode – Handset in base station – Handset outside base station

During a call approx. 1.5 W

General specifications

DECT standard is supported GAP standard is supported Range up to 300 m outdoors

Base station power supply 230 V ~/50 Hz Environmental conditions

123

operation

abc

approx. 1.3 W approx. 1.3 W

up to 50 m indoors

+5°C to +45°C, 20% to 75%

relative humidity

Questions and answers

If you have any queries about the use of your telephone, visit our website at www.gigaset.com/customercare for 24-hour support. The table below contains a lis t of common problems and possible solutions.

Problem Cause Solution

Nothing appears in the display.

No wireless connection to the base sta tion, Base flashes in the display.

You cannot hear a ringer/ dialling tone from the fixed line network.

Error tone sounds after system PIN prompt.

PIN forgotten.

The handset is not switched on.

The batteries are flat.

The handset is outside the range of the base sta

tion. The handset is not registered. The base station is not turned on.

The phone cord supplied has not been used or has been replaced by a new cord with the wrong jack connections.

You have entered the wrong system

PIN.

Press the end call key a for approx.

seconds or place

the handset in the base station. Charge or replace the batteries.

Move the handset closer to the base station.

¢ page 9.

Check the mains connector on the base station

¢ page 3.

Please always use the phone cord supplied or ensure that the pin

connections are correct when purchas ing from a retailer: 3-4 assignment of telephone leads/EURO CTR37.

Reset the system PIN to the default 0000

¢ page 10.

All handsets are deregistered. All set tings are reset. All lists are deleted.

Authorisation

This device is intended for analogue phone lines in your network.

Country-specific requirements have been taken into consideration.

We, Gigaset Communications GmbH, declare that this device meets the essential requirements and other relevant regulations laid down in Directive 1999/5/EC. A copy of the 1999/5/EC Declaration of Conformity is available at this Internet address: www.gigaset.com/docs.

Page 12

Service (Customer Care)

You can get assistance easily when you have technical questions or questions about how to use your device by using our online support service on the Internet at:

www.gigaset.com/customercare This site can be accessed at any time wherever you are. It will give you 24/7 support for all our products. It

also a list of FAQs and answers plus user guides for you to download. You will also find frequently asked questions and answers in the Questions and Answers section of this user guide in the appendix.

If the device needs to be repaired, please contact one of our Customer Care Centers:

Abu Dhabi. . . . . . . . . . . . .97 12 62 23 800

Argentina . . . . . . . . . . . . . 0800-888-9878

Australia . . . . . . . . . . . . . . . .1300 665 366

Austria .05 17 07 50 04 (0,065 Euro/Min.)

Bahrain . . . . . . . . . . . . . . . 97 31 73 11 173

Belgium . . . . . . . . . . . . . . . . 0 78 15 66 79

Bosnia Herzegovina . . . . . . . . 033 276 649

Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Grande Capitais e Regiões Metropolitanas:

. . . . . . . . . . . . . . . . . . . . . (11) 4003 3020

. . . . . . . . . . . . . . . . . .R$ 0,14 (US$ 0,069)

Demais localidades: . . . . . 0800 888 3020

. . . . . . . . . . . . . . . . . .R$ 0,20 (US$ 0,098)

Bulgaria. . . . . . . . . . . . . . . . . 02 873 94 88

Canada . . . . . . . . . . . . . . . . .866 247 8758

China . . . . 0 21 400 670 6007 (RMB 0.11)

Croatia . . . . . . . . 01 / 2456 555 (0,23 Kn)

Czech Republic . . . . . . . . . . . . 233 032 727

Denmark . . . . . . . . . . . . . . . . . 35 25 86 00

Dubai . . . . . . . . . . . . . . . . 97 14 39 69 944

Egypt. . . . . . . . . . . . . . . . . . . 202 7623441

Finland . . . . . . . . . . . . . . . . 09 23 11 34 25

France. . . 01 56 38 42 00 (Appel national)

Germany. . . . . . . . . . . . . . .01805 333 222

(0,14 Euro/Min. aus dem Festnetz der Deutschen Telekom. Für Anrufe aus den Mobilfunknetzen können abweichende Preise gelten)

Greece . . . . . . 801 1000 500 (0,026 Euro)

Hong Kong . . . . . . . . . . . . . . . . 2763 0203

. . . . . . . . . . . . . . . . . . . . . . . . . 2389 7285

Hungary . . . . . . . . . 06 14 71 24 44 (27 Ft)

India . . . . . . . . . . . . . . .Please refer to your

. . . . . . . . . . . . . . . . . . .local warranty card

Ireland . . . . . . . . . . . . . . . .18 50 77 72 77

Israel . . . . . . . . . . . . . . . . . . 1 700 700 727

Italy. . . . . . . . . . . . . . . . . . . . 199.15.11.15

Jordan . . . . . . . . . . .00962 6 5625460/1/2

Kuwait . . . . . . . . . . . . . . . 00965-2464993

Latvia . . . . . . . . . . . . . . . . . . . . . 7 50 11 18

Lebanon. . . . . . . . . . . . . . 00961-1236110

Luxembourg . . . . . . . . . . . 40 66 61 56 40

Malaysia. . . . . . . . . . . . . . . .603 77124304

Malta . . . . . . . . . . . . . . +353 21 4940 632

Mexico. .01800 999 4442738 (01800 999 Gigaset) Netherlands

. . . . . . . . .0900-3333102 (0,25 Euro/min.)

New Zealand . . . . . . . . . . . 08 00 27 43 63

Norway . . . . . . . . . . . . . . . . . . 22 70 84 00

Oman. . . . . . . . . . . . . . . . 96 82 47 09 281

Poland . . . . . . . . . . . . . . . . .0 801 140 160

Portugal. . . . . . . . . . . . (351) 808 781 223

Romania . . . . . . . . . . . . +4.021.529.7114.

Russia. . . . . . . . . . . . . . . 8 (495) 228 1312

Serbia. . . . . . . . . . . . . . . . . . 0800 222 111

Singapore . . . . . . . . . . . . . . . . . 6735 9100

Slovak Republic

. . . . . . . . . . . . . 02 59 68 22 66 (4,428 sk)

Slovenija . . . . . . . . . . . . . . . 0 14 74 63 36

South Africa. . . . . . . . . . . . 08 60 10 11 57

Spain . . . . . . . . . . . . . . . . . . . . 902 103935

Sweden . . . . . . . . . . . . . . . . . 08 750 99 11

Switzerland

. . . . . . . . . . 0848 212 000 (0,08 SFr./Min.)

Taiwan. . . . . . . . . . . . . . . . . 02 266 24343

Thailand. . . . . . . . . . . . . . . . . 02 722 1118

Turkey . . . . . . . . . . . . . . . .0216 459 98 59

Ukraine . . . . . . . . . . . .+380-44-451-71-72

United Arab Emirates . . . . . 0 43 66 03 86

United Kingdom . . . . . . .0 84 53 67 08 12

USA . . . . . . . . . . . . . . . . . 1-866 247-8758

. . . . . . . . . . . . . . . . . . . . . . . . . . . (toll free)

Please have your record of purchase ready when calling. Replacement or repair services are not offered in countries where our product is not sold by

authorised dealers.

Page 13

Menu tree

Your phone has an extensive range of features. These are offered in the form of menus. To select a function while the phone is in idle sta- tus, press MENU (open menu), use the t and v keys to scroll to the function you require and press

OK to confirm.

As an alternative to selecting functions using the

t and v buttons, you can also enter the digit

combination that is in front of the function in the menu tree. For setting the time and date, for example:

MENU ¢ 4 1 ¢ OK

To return to idle status: press and hold the a key.

1 Alarm Clock

1-1 Activation Activating/deactivating the alarm clock

1-2 Wake-up time Input format: HHMM

2 Audio Settings

2-1 Handset Vol-

ume

2-1 Handset Vol-

ume

2-2 Ringer Volume 5 levels + "crescendo" available

2-3 Ringer Melody 2-3-1 External Calls 10 ringer melodies available for external calls

2-4 Advis. Tones Activate/deactivate

2-5 Battery Low 2-5-1 Off Warning tone to indicate

3 Voice Mail

3-1 Set Key 1

(all devices)

Can be set to one of 3 levels (AS180)

2-1-1 Earpiece Can be set to one of 3 levels (AS280)

2-1-2 Speaker Can be set to one of 5 levels (AS280)

2-3-2 Internal Calls 10 ringer melodies available for internal calls

2-3-3 Alarm Clock 10 ringer melodies available for alarm clock

2-5-2 On always

2-5-3 During Call only during a call

3-1-1 Netw. Mailbx Assign key 1 with network mailbox and enter the network mailbox

battery is almost flat:

number (in idle status, press and hold key 1 to dial). Netw. Mailbx: your network provider's answer machine; must be requested separately. The network mailbox list can be displayed if your network provider supports this function and if key assigned with the network mailbox.

never

1 has been

Page 14

4 Settings

4-1 Date/Time Enter date (DDMMYY format), then time (HHMM format) 4-2 Handset 4-2-1 Language Set the display language ¢ page 10

4-2-2 Auto Answer Automatically activate/deactivate auto answer ¢ page 7 4-2-3 Register HS Manually register the handset ¢ page 9 4-2-4 Reset Handset Reset the handset ¢ page 10

4-3 Base 4-3-2 Call list type 4-3-2-1 Missed Calls ¢ page 8

4-3-2-2 All Calls ¢ page 8

4-3-3 System PIN Change system PIN (default is 0000) 4-3-4 Base Reset Restore factory settings ¢ page 10 4-3-5 Additional 4-3-5-1 Repeater activate/deactivate ¢ page 10

4-3-5-2 Eco Mode+ activate/deactivate ¢ page 2 4-3-5-3 Eco Mode activate/deactivate ¢ page 2

4-3-6 Listening in Activate/deactivate the function ¢ page 9

4-3-7 Preselection 4-3-7-1 Presel. Number Network provider dialling code,

4-3-7-2 With Preselect First digits of the dialling codes,

4-3-7-3 Without Presel First digits of dialling codes, should

should be inserted automatically before the dialled phone number.

should be dialled with preselection.

be dialled without preselection.