查询ST380CH04C0供应商
PHASE CONTROL THYRISTORS Hockey Puk Version
Features
Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AB (E-PUK)
Low profile hockey-puk to increase current-carrying capability
Extended temperature range
Bulletin I25169 rev. C 04/00
ST380CH..C SERIES
960A
Typical Applications
DC motor controls
Controlled DC power supplies
AC controllers
Major Ratings and Characteristics
Parameters ST380CH..C Units
I
T(AV)
@ T
hs
I
T(RMS)
@ T
hs
I
TSM
I2t@
V
DRM/VRRM
t
q
T
J
@ 50Hz 12500 A
@ 60Hz 13000 A
50Hz 782 KA2s
@ 60Hz 713 KA
typical 100 µs
960 A
80 °C
2220 A
25 °C
400 to 600 V
- 40 to 150 °C
case style TO-200AB (E-PUK)
2
s
www.irf.com
1
ST380CH..C Series
Bulletin I25169 rev. C 04/00
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage V
DRM/VRRM
Type number Code peak and off-state voltage repetitive peak voltage @ T
ST380CH..C 100
04 400 500
06 600 700
On-state Conduction
Parameter ST380CH..C Units Conditions
Max. average on-state current 960 (440) A 180° conduction, half sine wave
I
T(AV)
@ Heatsink temperature 80 (110) °C double side (single side) cooled
Max. RMS on-state current 2220 DC @ 25°C heatsink temperature double side cooled
I
T(RMS)
I
Max. peak, one-cycle 12500 t = 10ms No voltage
TSM
non-repetitive surge current 13000 A t = 8.3ms reapplied
2
I
t Maximum I2t for fusing 782 t = 10ms No voltage Initial TJ = TJ max.
2
I
√t Maximum I2√t for fusing 7820 KA2√s t = 0.1 to 10ms, no voltage reapplied
V
Low level value of threshold
T(TO)
1
voltage
High level value of threshold
V
T(TO)
2
voltage
Low level value of on-state
r
t1
slope resistance
High level value of on-state
r
t2
slope resistance
Max. on-state voltage 1.58 V Ipk= 2900A, TJ = TJ max, tp = 10ms sine pulse
V
TM
I
Maximum holding current 600
H
I
Typical latching current 1000
L
, max. repetitive V
, maximum non- I
RSM
DRM/IRRM
VVmA
10500 t = 10ms 100% V
11000 t = 8.3ms reapplied Sinusoidal half wave,
713 t = 8.3ms reapplied
553 t = 10ms 100% V
KA2s
505 t = 8.3ms reapplied
0.85 (16.7% x π x I
V
0.88 (I > π x I
T(AV)
0.25 (16.7% x π x I
mΩ
0.24 (I > π x I
T(AV)
mA TJ = 25° C, anode supply 12V resistive load
RRM
RRM
< I < π x I
T(AV)
),TJ = TJ max.
< I < π x I
T(AV)
),TJ = TJ max.
), TJ = TJ max.
T(AV)
), TJ = TJ max.
T(AV)
max.
= TJ max
J
Switching
Parameter ST380CH..C Units Conditions
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, t
of turned-on current T
t
Typical delay time 1.0
d
t
Typical turn-off time 100
q
1000 A/µs
µs
= TJ max, anode voltage ≤ 80% V
J
Gate current 1A, d ig/dt = 1A/µs
= 0.67% V
V
d
I
= 550A, TJ = TJ max, di/dt = 40A/µs, VR = 50V
TM
dv/dt
DRM, TJ
= 20V/µs, Gate 0V 100Ω, tp = 500µs
2
≤ 1µs
r
= 25°C
DRM
www.irf.com
Blocking
Parameter ST380CH..C Units Conditions
dv/dt Maximum critical rate of rise of
off-state voltage
I
Max. peak reverse and off-state
RRM
leakage current
I
DRM
500 V /µsTJ = TJ max. linear to 80% rated V
100 mA TJ = TJ max, rated V
Triggering
Parameter ST380CH..C Units Conditions
PGMMaximum peak gate power 10.0 TJ = TJ max, tp ≤ 5ms
P
Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50
G(AV)
Max. peak positive gate current 3.0 A TJ = TJ max, tp ≤ 5ms
I
GM
+V
Maximum peak positive
GM
gate voltage
Maximum peak negative
-V
GM
gate voltage
20
5.0
TYP. MAX.
DC gate current required
I
GT
to trigger
200 -
100 200
40 -
V
DC gate voltage required
GT
to trigger
I
DC gate current not to trigger 10 mA
GD
2.5 -
1.8 3.0
1.0 -
VGDDC gate voltage not to trigger 0.25 V
W
= TJ max, tp ≤ 5ms
VT
J
T
= - 40°C
J
= 25°C
mA T
J
TJ = 150°C
TJ = - 40°C
VTJ = 25°C
T
= 150°C
J
= TJ max
T
J
ST380CH..C Series
Bulletin I25169 rev. C 04/00
DRM
applied
DRM/VRRM
Max. required gate trigger/ current/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied
Max. gate current/voltage not to
trigger is the max. value which
will not trigger any unit with rated
anode-to-cathode applied
V
DRM
Thermal and Mechanical Specification
Parameter ST380CH..C Units Conditions
T
Max. operating temperature range -4 0 to 150
J
Max. storage temperature range - 40 to 15 0
T
stg
R
Max. thermal resistance, 0.09 DC operation single side cooled
thJ-hs
junction to heatsink 0.04 DC operation double side cooled
Max. thermal resistance, 0.02 DC operation single side cooled
R
thC-hs
case to heatsink 0.01 DC operation double side cooled
F Mounting force, ± 10% 9800 N
(1000) (Kg)
wt Approximate weight 83 g
Case style TO - 200AB (E-PUK) See Outline Table
°C
K/W
K/W
www.irf.com
3
ST380CH..C Series
Bulletin I25169 rev. C 04/00
∆R
Conduction
thJ-hs
(The following table shows the increment of thermal resistence R
Conduction angle Units Conditions
180° 0.010 0.011 0.007 0.007 T
120° 0.012 0.012 0.012 0.013
90° 0.015 0.015 0.016 0.017 K/W
60° 0.022 0.022 0.023 0.023
30° 0.036 0.036 0.036 0.037
Sinusoidal conduction Rectangular conduction
Single Side Double Side Single Side Double Side
Ordering Information Table
Device Code
ST 38 0 CH 06 C 1
when devices operate at different conduction angles than DC)
thJ-hs
J
= TJ max.
3 4
51 2
768
1 - Thyristor
2 - Essential part number
3 - 0 = Converter grade
4 - CH = Ceramic Puk, High temperature
5 - Voltage code: Code x 100 = V
(See Voltage Rating Table)
RRM
6 - C = Puk Case TO-200AB (E-PUK)
7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)
1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8 - Critical dv/dt: None = 500V/µsec (Standard selection)
L = 1000V/µsec (Special selection)
4
www.irf.com
Outline Table
ANODE TO GATE
CREEPAGE DISTANCE: 11.18 (0.44) MIN.
STRIKE DISTANCE: 7.62 (0.30) MIN.
25.3 (0.99)
DIA. MAX.
25.3 (0.99)
DIA. MAX.
40.5 (1.59) DIA. MAX.
2 HOLES 3.56 (0.14) x
1.83 (0.07) MIN. DEEP
GATE TERM. FOR
1.47 (0.06) DIA.
PIN RECEPTACLE
0.3 (0.01) MIN.
6.5 (0.26)
14.1 / 15.1
(0.56 / 0.59)
0.3 (0.01) MIN.
ST380CH..C Series
Bulletin I25169 rev. C 04/00
4.75 (0.19)
Case Style TO-200AB (E-PUK)
All dimensions in millimeters (inches)
25°± 5°
42 (1.65) MAX.
28 (1.10)
150
140
130
120
110
100
ST380 CH ..C Series
(Single S ide Cooled)
R (D C ) = 0.09 K /W
thJ-h s
Con duc tion Angle
150
140
130
120
110
100
90
80
70
60
30°
60°
90°
120°
180°
50
40
0 100 200 300 400 500 600 700 800
M aximum A llow able He atsin k Tem p erature (°C)
Maximum Allowable Heatsink Temperature (°C)
Average On-state Current (A)
Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics
Quote between upper and lower
pole pieces has to be considered
after application of Mounting Force
(see Thermal and Mechanical
Specification)
ST380C H..C Series
(Single Side Cooled)
R (D C) = 0.09 K/W
thJ-h s
90
80
70
60
50
40
30
20
30°
60°
90°
120°
0 200 400 600 800 1000 1200 1400
A ve ra g e O n-sta te C urre nt (A )
Conduction Period
180°
DC
www.irf.com
5
ST380CH..C Series
Bulletin I25169 rev. C 04/00
150
140
130
120
ST380CH..C Series
(Double Sid e Cooled)
R (DC) = 0.04 K/W
th J-hs
110
100
90
Conduction Angle
80
70
60
50
40
30°
60°
90°
120°
30
20
0 400 800 1200 1600
Maximum Allowable Heatsin k Temperature (°C)
Average On-state Current (A)
Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics
2500
180°
2000
120°
90°
60°
1500
30°
1000
Conduction Angle
500
0
M axim um Av erag e On-state P ow er Loss (W)
0 400 800 1200 1600
ST380CH..C Series
T = 150°C
J
Av erag e O n- sta t e C urre nt (A )
Fig. 5- On-state Power Loss Characteristics
180°
RMS Limit
150
140
130
120
ST380C H..C Series
(Doub le Side C o ole d)
R (D C) = 0.04 K/W
thJ-h s
110
100
90
Conduction Period
80
70
60
50
40
30
20
Ma ximum A llowable Heatsink Tem perature (° C)
30°
60°
90°
120°
180°
0 500 1000 1500 2000 2500
Average On-state Current (A)
3500
DC
180°
3000
120°
2500
90°
60°
30°
2000
RMS Limit
1500
1000
Conduction Period
500
0
M a xim um A verage O n - sta te Po w e r Loss (W )
0 500 1000 1500 2000 2500
ST380C H..C Series
T = 150°C
J
Av erag e O n- sta te C urren t (A )
Fig. 6- On-state Power Loss Characteristics
DC
12000
At Any Rated Load Condition And With
Rated V Applied Following Surge.
11000
10000
RRM
In it i a l T = 1 50° C
J
@ 60 Hz 0.0083 s
@ 50 Hz 0.0100 s
9000
8000
7000
ST380CH..C Series
6000
Peak Half Sine W ave On-state Current (A)
5000
110100
Num ber Of Equal Amplitude Half Cycle Current Pulses (N)
Fig. 7 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
6
13000
Max im um N on Repetitive Surge C urrent
12000
11000
10000
V ersu s P ulse Tra in D ura tio n . C on tro l
Of Con duction M ay Not Be Maintained .
Initia l T = 15 0 ° C
No Voltage Reapplie d
Rate d V Rea p p lied
RRM
9000
8000
7000
ST380C H..C Series
6000
Pe ak Ha lf Sine W ave O n-state Current (A)
5000
0.01 0.1 1
Pulse Train Duration (s)
Fig. 8 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
www.irf.com
J
ST380CH..C Series
Bulletin I25169 rev. C 04/00
10000
T = 25°C
J
T = 150°C
J
1000
ST380CH ..C Series
Instantaneous On-state Current (A)
100
0.511.522.533.5
Instantaneous On-state Voltage (V)
Fig. 9 - On-state Voltage Drop Characteristics
0.1
ST380C H..C Series
thJ-h s
0.01
0.001
Transient Therm al Impedanc e Z (K/W )
0 .00 1 0.0 1 0 .1 1 10
Squ a re W a ve P ulse D u ration (s)
Fig. 10 - Thermal Impedance Z
100
R e ct a n g u la r g a te p u lse
a) Recomm ended load line for
rate d di/dt : 2 0V , 10o hm s; tr<=1 µ s
b ) R e c om m en de d l o a d lin e f o r
<= 3 0% rate d d i/d t : 10V, 1 0ohm s
10
t r<=1 µ s
Tj = 25 °C
1
Insta nt ane ou s G a te V olta g e (V)
0.1
0 .00 1 0 .01 0 .1 1 10 1 00
VGD
IG D
Tj=150 °C
Device: ST380CH ..C Se ries
Instantaneous G ate C urrent (A)
thJ-hs
(a)
(b )
Tj=-40 °C
S t e a d y S t a t e V a lu e
R = 0.09 K/W
thJ-hs
(Sing le Side C ooled)
R = 0.04 K/W
thJ-hs
(D o uble S ide Co oled )
(D C O pera tion)
Characteristics
(1) PG M = 10W , tp = 4m s
(2) PG M = 20W , tp = 2m s
(3) PG M = 40W , tp = 1m s
(4) P GM = 6 0W , tp = 0.66m s
(1) (4)
Frequency Lim ited by PG(AV )
Fig. 11 - Gate Characteristics
(2)
(3)
www.irf.com
7
Loading...