International Rectifier IRL2203N Datasheet
PD - 91366
IRL2203N
HEXFET® Power MOSFET
l Advanced Process Technology
l Ultra Low On-Resistance
l Dynamic dv/dt Rating
l 175°C Operating Temperature
l Fast Switching
l Fully Avalanche Rated
G
D
R
DS(on)
V
DSS
= 30V
= 7.0mΩ
ID = 116A
S
Description
Advanced HEXFET® Power MOSFETs from International
Rectifier utilize advanced processing techniques to achieve
extremely low on-resistance per silicon area. This benefit,
combined with the fast switching speed and ruggedized
device design that HEXFET power MOSFETs are well
known for, provides the designer with an extremely efficient
and reliable device for use in a wide variety of applications.
The TO-220 package is universally preferred for all
commercial-industrial applications at power dissipation
levels to approximately 50 watts. The low thermal
resistance and low package cost of the TO-220 contribute
TO-220AB
to its wide acceptance throughout the industry.
Absolute Maximum Ratings
Parameter Max. Units
ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 116
ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 82 A
I
DM
PD @TC = 25°C Power Dissipation 180 W
V
GS
I
AR
E
AR
dv/dt Peak Diode Recovery dv/dt 5.0 V/ns
T
J
T
STG
Pulsed Drain Current 400
Linear Derating Factor 1.2 W/°C
Gate-to-Source Voltage ± 16 V
Avalanche Current 60 A
Repetitive Avalanche Energy 18 mJ
Operating Junction and -55 to + 175
Storage Temperature Range
Soldering Temperature, for 10 seconds 300 (1.6mm from case )
Mounting torque, 6-32 or M3 srew 10 lbf•in (1.1N•m)
°C
Thermal Resistance
Parameter Typ. Max. Units
R
θJC
R
θCS
R
θJA
www.irf.com 1
Junction-to-Case ––– 0.85
Case-to-Sink, Flat, Greased Surface 0.50 ––– °C/W
Junction-to-Ambient ––– 62
3/16/01
IRL2203N
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter Min. Typ. Max. Units Conditions
V
(BR)DSS
∆V
(BR)DSS
R
DS(on)
V
GS(th)
g
fs
I
DSS
I
GSS
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
L
D
L
S
C
iss
C
oss
C
rss
E
AS
Drain-to-Source Breakdown Voltage 30 –– – ––– V VGS = 0V, ID = 250µA
/∆T
Breakdown Voltage Temp. Coefficient ––– 0.029 ––– V/°C Reference to 25°C, ID = 1mA
J
Static Drain-to-Source On-Resistance
––– ––– 7.0 VGS = 10V, ID = 60A
––– ––– 10 VGS = 4.5V, ID = 48A
mΩ
Gate Threshold Voltage 1.0 ––– ––– V VDS = VGS, ID = 250µA
Forward Transconductance 73 ––– ––– S VDS = 25V, ID = 60A
Drain-to-Source Leakage Current
––– ––– 25
––– ––– 250 VDS = 24V, VGS = 0V, TJ = 125°C
Gate-to-Source Forward Leakage ––– ––– 100 VGS = 16V
Gate-to-Source Reverse Leakage ––– ––– -100
VDS = 30V, VGS = 0V
µA
nA
VGS = -16V
Total Gate Charge ––– ––– 60 ID = 60A
Gate-to-Source Charge ––– ––– 14 nC VDS = 24V
Gate-to-Drain ("Miller") Charge ––– ––– 33 VGS = 4.5V, See Fig. 6 and 13
Turn-On Delay Time ––– 11 ––– VDD = 15V
Rise Time ––– 160 ––– ID = 60A
Turn-Off Delay Time ––– 23 ––– RG = 1.8Ω
Fall Time ––– 66 ––– VGS = 4.5V, See Fig. 10
Internal Drain Inductance ––– 4.5 –––
Internal Source Inductance ––– 7.5 –––
Between lead,
6mm (0.25in.)
nH
from package
and center of die contact
Input Capacitance ––– 3290 ––– VGS = 0V
Output Capacitance ––– 1270 ––– VDS = 25V
Reverse Transfer Capacitance ––– 170 ––– pF ƒ = 1.0MHz, See Fig. 5
Single Pulse Avalanche Energy ––– 1320290 mJ I
= 60A, L = 0.16mH
AS
D
G
S
Source-Drain Ratings and Characteristics
Parameter Min. Typ. Max. Units Conditions
I
S
I
SM
V
SD
t
rr
Q
rr
t
on
Continuous Source Current MOSFET symbol
(Body Diode)
Pulsed Source Current integral reverse
(Body Diode)
––– –––
––– –––
116
400
showing the
A
p-n junction diode.
G
Diode Forward Voltage ––– ––– 1.2 V TJ = 25°C, IS = 60A, VGS = 0V
Reverse Recovery Time ––– 56 84 ns TJ = 25°C, IF = 60A
Reverse Recovery Charge ––– 110 170 nC di/dt = 100A/µs
Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
Repetitive rating; pulse width limited by
max. junction temperature. ( See fig. 11 )
Starting T
RG = 25Ω, I
= 25°C, L = 0.16mH
J
= 60A, VGS=10V (See Figure 12)
AS
≤ 60A, di/dt ≤ 110A/µs, V
SD
TJ ≤ 175°C
Pulse width ≤ 400µs; duty cycle ≤ 2%.
This is a typical value at device destruction and represents
operation outside rated limits.
This is a calculated value limited to T
DD
≤ V
(BR)DSS
= 175°C .
J
,
I
Calculated continuous current based on maximum allowable
junction temperature. Package limitation current is 75A.
2 www.irf.com
D
S
IRL2203N
1000
100
10
D
I , Drain-to-Source Current (A)
1
0.1 1 10 100
1000
VGS
TOP
15V
10V
4.5V
3.7V
3.5V
3.3V
3.0V
BOTTOM
2.7V
2.7V
20µs PULSE WIDTH
T = 25 C
J
V , Drain-to-Source Voltage (V)
DS
°
1000
100
10
D
I , Drain-to-Source Current (A)
1
0.1 1 10 100
VGS
TOP
15V
10V
4.5V
3.7V
3.5V
3.3V
3.0V
BOTTOM
2.7V
2.7V
20µs PULSE WIDTH
T = 175 C
V , Drain-to-Source Voltage (V)
DS
°
J
Fig 2. Typical Output CharacteristicsFig 1. Typical Output Characteristics
2.5
100A
I =
D
°
T = 25 C
J
T = 175 C
J
100
D
I , Drain-to-Source Current (A)
V = 15V
DS
10
2.0 3.0 4.0 5.0 6.0 7.0
V , Gate-to-Source Voltage (V)
GS
20µs PULSE WIDTH
Fig 3. Typical Transfer Characteristics
°
2.0
1.5
1.0
(Normalized)
0.5
DS(on)
R , Drain-to-Source On Resistance
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180
T , Junction Temperature ( C)
J
Fig 4. Normalized On-Resistance
V =
10V
GS
°
Vs. Temperature
www.irf.com 3
Loading...