International Rectifier IRFP254N Datasheet
PD - 94213
IRFP254N
HEXFET® Power MOSFET
l Advanced Process Technology
l Dynamic dv/dt Rating
l 175°C Operating Temperature
l Fast Switching
l Fully Avalanche Rated
l Ease of Paralleling
l Simple Drive Requirements
G
D
V
R
DS(on)
= 250V
DSS
= 125mΩ
ID = 23A
S
Description
Fifth Generation HEXFETs from International Rectifier utilize advanced processing
techniques to achieve extremely low on-resistance per silicon area. This benefit,
combined with the fast switching speed and ruggedized device design that
HEXFET Power MOSFETs are well known for, provides the designer with an
extremely efficient and reliable device for use in a wide variety of applications.
The TO-247 package is preferred for commercial-industrial applications where
higher power levels preclude the use of TO-220 devices. The TO-247 is similar
but superior to the earlier TO-218 package because of its isolated mounting hole.
TO-247AC
Absolute Maximum Ratings
Parameter Max. Units
ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 23
ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 16 A
I
DM
PD @TC = 25°C Power Dissipation 220 W
V
GS
E
AS
I
AR
E
AR
dv/dt Peak Diode Recovery dv/dt 7.4 V/ns
T
J
T
STG
Pulsed Drain Current 92
Linear Derating Factor 1.5 W/°C
Gate-to-Source Voltage ± 20 V
Single Pulse Avalanche Energy 300 mJ
Avalanche Current 14 A
Repetitive Avalanche Energy 22 m J
Operating Junction and -55 to + 175
Storage Temperature Range
Soldering Temperature, for 10 seconds 300 (1.6mm from case )
Mounting torque, 6-32 or M3 srew 10 lbf•in (1.1N•m)
°C
Thermal Resistance
Parameter Typ. Max. Units
R
θJC
R
θCS
R
θJA
www.irf.com 1
Junction-to-Case ––– 0.68
Case-to-Sink, Flat, Greased Surface 0.24 ––– °C/W
Junction-to-Ambient ––– 40
7/20/01
IRFP254N
Electrical Characteristics @ TJ = 25°C (unless otherwise specified)
Parameter Min. Typ. Max. Units Conditions
V
(BR)DSS
∆V
(BR)DSS
R
DS(on)
V
GS(th)
g
fs
I
DSS
I
GSS
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
L
D
L
S
C
iss
C
oss
C
rss
Drain-to-Source Breakdown Voltage 250 ––– –– – V VGS = 0V, ID = 250µA
/∆T
Breakdown Voltage Temp. Coefficient ––– 0.33 ––– V/°C Reference to 25°C, ID = 1mA
J
Static Drain-to-Source On-Resistance ––– ––– 125 mΩ VGS = 10V, ID = 14A
Gate Threshold Voltage 2.0 ––– 4.0 V VDS = VGS, ID = 250µA
Forward Transconductance 15 ––– ––– S VDS = 25V, ID = 14A
Drain-to-Source Leakage Current
––– ––– 25
––– ––– 250 VDS = 200V, VGS = 0V, TJ = 150°C
Gate-to-Source Forward Leakage ––– ––– 100 VGS = 20V
Gate-to-Source Reverse Leakage ––– ––– -100
VDS = 250V, VGS = 0V
µA
nA
VGS = -20V
Total Gate Charge ––– ––– 100 ID = 14A
Gate-to-Source Charge ––– ––– 17 nC VDS = 200V
Gate-to-Drain ("Miller") Charge ––– ––– 44 VGS = 10V, See Fig. 6 and 13
Turn-On Delay Time ––– 14 ––– VDD = 125V
Rise Time ––– 34 ––– ID = 14A
Turn-Off Delay Time ––– 37 – –– RG = 3.6Ω
ns
Fall Time ––– 29 ––– VGS = 10V, See Fig. 10
5.0
Internal Drain Inductance
Internal Source Inductance ––– –––
––– –––
13
Between lead,
6mm (0.25in.)
nH
from package
and center of die contact
Input Capacitance ––– 2040 ––– VGS = 0V
Output Capacitance ––– 260 ––– VDS = 25V
Reverse Transfer Capacitance ––– 62 ––– pF ƒ = 1.0MHz, See Fig. 5
D
G
S
Source-Drain Ratings and Characteristics
Parameter Min. Typ. Max. Units Conditions
I
S
I
SM
V
SD
t
rr
Q
rr
t
on
Continuous Source Current MOSFET symbol
(Body Diode)
Pulsed Source Current integral reverse
(Body Diode)
––– –––
––– –––
23
92
showing the
A
p-n junction diode.
G
Diode Forward Voltage ––– ––– 1.3 V TJ = 25°C, IS = 14A, VGS = 0V
Reverse Recovery Time ––– 210 310 ns TJ = 25°C, IF = 14A
Reverse Recovery Charge ––– 1.7 2.6 µC di/dt = 100A/µs
Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
Notes:
I
Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11)
Starting T
RG = 25Ω, I
= 25°C, L = 3.1mH
J
= 14A,VGS=10V
AS
≤ 14A, di/dt ≤ 460A/µs, V
SD
TJ ≤ 175°C
Pulse width ≤ 400µs; duty cycle ≤ 2%.
DD
≤ V
(BR)DSS
,
2 www.irf.com
D
S
IRFP254N
100
10
1
D
I , Drain-to-Source Current (A)
0.1
0.1 1 10 100
100
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
4.5V
20µs PULSE WIDTH
T = 25 C
J
V , Drain-to-Source Voltage (V)
DS
°
100
10
D
I , Drain-to-Source Current (A)
1
0.1 1 10 100
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
20µs PULSE WIDTH
T = 175 C
V , Drain-to-Source Voltage (V)
DS
4.5V
°
J
Fig 2. Typical Output CharacteristicsFig 1. Typical Output Characteristics
4.0
23A
I =
D
°
T = 175 C
J
10
°
T = 25 C
J
D
I , Drain-to-Source Current (A)
V = 50V
DS
1
4.0 5.0 6.0 7.0 8.0 9.0
V , Gate-to-Source Voltage (V)
GS
20µs PULSE WIDTH
Fig 3. Typical Transfer Characteristics
3.0
2.0
(Normalized)
1.0
DS(on)
R , Drain-to-Source On Resistance
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 160 180
T , Junction Temperature ( C)
J
Fig 4. Normalized On-Resistance
V =
10V
GS
°
Vs. Temperature
www.irf.com 3
Loading...