International Rectifier IRF820AS, IRF820AL Datasheet
SMPS MOSFET
PD- 93774A
IRF820AS
IRF820AL
HEXFET® Power MOSFET
Applications
l Switch Mode Power Supply (SMPS)
l Uninterruptable Power Supply
l High speed power switching
V
DSS
RDS(on) max I
500V 3.0Ω 2.5A
Benefits
l Low Gate Charge Qg Results in Simple
Drive Requirement
l Improved Gate, Avalanche and Dynamic
dv/dt Ruggedness
l Fully Characterized Capacitance and
Avalanche Voltage and Current
l Effective C
specified (See AN 1001)
OSS
D2Pak
IRF820AS
TO-262
IRF820AL
Absolute Maximum Ratings
Parameter Max. Units
ID @ TC = 25°C Continuous Drain Current, VGS @ 10V 2.5
ID @ TC = 100°C Continuous Drain Current, VGS @ 10V 1.6 A
I
DM
PD @TC = 25°C Power Dissipation 50 W
V
GS
dv/dt Peak Diode Recovery dv/dt 3.4 V/ns
T
J
T
STG
Pulsed Drain Current 10
Linear Derating Factor 0.4 W/°C
Gate-to-Source Voltage ± 30 V
Operating Junction and -55 to + 150
Storage Temperature Range
Soldering Temperature, for 10 seconds 300 (1.6mm from case )
Mounting torqe, 6-32 or M3 screw 10 lbf•in (1.1N•m)
°C
D
Typical SMPS Topologies:
l Two Transistor Forward
l Half Bridge and Full Bridge
Notes through are on page 8
www.irf.com 1
5/8/00
IRF820AS/L
Static @ TJ = 25°C (unless otherwise specified)
Parameter Min. Typ. Max. Units Conditions
V
(BR)DSS
∆V
(BR)DSS
R
DS(on)
V
GS(th)
I
DSS
I
GSS
Dynamic @ TJ = 25°C (unless otherwise specified)
g
fs
Q
g
Q
gs
Q
gd
t
d(on)
t
r
t
d(off)
t
f
C
iss
C
oss
C
rss
C
oss
C
oss
C
eff. Effective Output Capacitance ––– 28 ––– VGS = 0V, VDS = 0V to 400V
oss
Avalanche Characteristics
E
AS
I
AR
E
AR
Drain-to-Source Breakdown Voltage 500 ––– ––– V VGS = 0V, ID = 250µA
/∆T
Breakdown Voltage Temp. Coefficient
J
––– 0.60 ––– V/°C Reference to 25°C, ID = 1mA
Static Drain-to-Source On-Resistance ––– ––– 3.0 Ω VGS = 10V, ID = 1.5A
Gate Threshold Voltage 2.0 –– – 4.5 V VDS = VGS, ID = 250µA
Drain-to-Source Leakage Current
––– ––– 25
––– ––– 250 VDS = 400V, VGS = 0V, TJ = 125°C
Gate-to-Source Forward Leakage ––– ––– 100 VGS = 30V
Gate-to-Source Reverse Leakage ––– ––– -100
VDS = 500V, VGS = 0V
µA
nA
VGS = -30V
Parameter Min. Typ. Max. Units Conditions
Forward Transconductance 1.4 ––– ––– S VDS = 50V, ID = 1.5A
Total Gate Charge ––– ––– 17 ID = 2.5A
Gate-to-Source Charge ––– ––– 4.3 nC VDS = 400V
Gate-to-Drain ("Miller") Charge ––– ––– 8.5 VGS = 10V, See Fig. 6 and 13
Turn-On Delay Time ––– 8.1 ––– VDD = 250V
Rise Time ––– 12 ––– ID = 2.5A
Turn-Off Delay Time ––– 16 ––– RG = 21Ω
ns
Fall Time ––– 13 ––– RD = 97Ω,See Fig. 10
Input Capacitance ––– 340 ––– VGS = 0V
Output Capacitance ––– 53 ––– VDS = 25V
Reverse Transfer Capacitance ––– 2.7 ––– pF ƒ = 1.0MHz, See Fig. 5
Output Capacitance ––– 490 ––– VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz
Output Capacitance ––– 15 ––– VGS = 0V, VDS = 400V, ƒ = 1.0MHz
Parameter Typ. Max. Units
Single Pulse Avalanche Energy ––– 140 mJ
Avalanche Current ––– 2.5 A
Repetitive Avalanche Energy ––– 5.0 mJ
Thermal Resistance
Parameter Typ. Max. Units
R
θJC
R
θJA
Junction-to-Case ––– 2.5 °C/W
Junction-to-Ambient ( PCB Mounted, steady-state)* ––– 62
Diode Characteristics
Parameter Min. Typ. Max. Units Conditions
I
S
I
SM
V
SD
t
rr
Q
rr
t
on
Continuous Source Current MOSFET symbol
(Body Diode)
Pulsed Source Current integral reverse
(Body Diode)
––– –––
––– –––
2.5
10
showing the
A
p-n junction diode.
G
Diode Forward Voltage ––– ––– 1.6 V TJ = 25°C, IS = 2.5A, VGS = 0V
Reverse Recovery Time ––– 330 500 ns TJ = 25°C, IF = 2.5A
Reverse RecoveryCharge –– – 760 1140 nC di/dt = 100A/µs
Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
2 www.irf.com
D
S
IRF820AS/L
10
1
0.1
D
I , Drain-to-Source Current (A)
0.01
0.1 1 10 100
10
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
20µs PULSE WIDTH
T = 25 C
J
V , Drain-to-Source Voltage (V)
DS
4.5V
°
10
1
D
I , Drain-to-Source Current (A)
0.1
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
4.5V
20µs PULSE WIDTH
T = 150 C
1 10 100
V , Drain-to-Source Voltage (V)
DS
°
J
Fig 2. Typical Output CharacteristicsFig 1. Typical Output Characteristics
3.0
2.5A
I =
D
°
T = 150 C
J
1
°
T = 25 C
J
0.1
D
I , Drain-to-Source Current (A)
V = 50V
DS
0.01
4.0 5.0 6.0 7.0 8.0 9.0
V , Gate-to-Source Voltage (V)
GS
20µs PULSE WIDTH
Fig 3. Typical Transfer Characteristics
2.5
2.0
1.5
(Normalized)
1.0
0.5
DS(on)
R , Drain-to-Source On Resistance
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 160
T , Junction Temperature ( C)
J
Fig 4. Normalized On-Resistance
V =
10V
GS
°
Vs. Temperature
www.irf.com 3
Loading...