International Rectifier IRF5M3710 Datasheet
PD - 94234
HEXFET
®
POWER MOSFET
THRU-HOLE (TO-254AA)
Product Summary
Part Number BV
DSS
IRF5M3710 100V 0.03Ω 35A*
Fifth Generation HEXFET® power MOSFETs from
International Rectifier utilize advanced processing
techniques to achieve the lowest possible on-resistance
per silicon unit area. This benefit, combined with the
fast switching speed and ruggedized device design
that HEXFET power MOSFETs are well known for,
provides the designer with an extremely efficient device
for use in a wide variety of applications.
These devices are well-suited for applications such
as switching power supplies, motor controls, inverters, choppers, audio amplifiers and high-energy pulse
circuits.
RDS(on) ID
IRF5M3710
100V, N-CHANNEL
TO-254AA
Features:
n Low RDS(on)
n Avalanche Energy Ratings
n Dynamic dv/dt Rating
n Simple Drive Requirements
n Ease of Paralleling
n Hermetically Sealed
n Light Weight
Absolute Maximum Ratings
Parameter Units
ID @ VGS = 10V, TC = 25°C Continuous Drain Current 35*
ID @ VGS = 10V, TC = 100°C Continuous Drain Current 29
I
DM
PD @ TC = 25°C Max. Power Dissipation 125 W
V
GS
E
AS
I
AR
E
AR
dv/dt Peak Diode Recovery dv/dt ➂ 4.0
T
J
T
STG
* Current is limited by package
For footnotes refer to the last page
Pulsed Drain Current ➀ 140
Linear Derating Factor 1.0 W/°C
Gate-to-Source Voltage ±20 V
Single Pulse Avalanche Energy ➁ 350 mJ
Avalanche Current ➀ 28 A
Repetitive Avalanche Energy ➀ 12.5 mJ
Operating Junction -55 to 150
Storage Temperature Range
Lead Temperature 300 (0.063in./1.6mm from case for 10s)
Weight 9.3 (Typical) g
www.irf.com 1
A
V/ns
o
C
06/08/01
IRF5M3710
Electrical Characteristics @ Tj = 25°C (Unless Otherwise Specified)
Parameter Min Typ Max Units Test Conditions
BV
∆BV
R
V
g
I
DSS
I
GSS
I
GSS
Q
Q
Q
t
d(on)
t
r
t
d(off)
t
f
LS + L
C
C
C
DSS
DSS
DS(on)
GS(th)
fs
g
gs
gd
D
iss
oss
rss
Drain-to-Source Breakdown Voltage 100 — — V VGS = 0V, ID = 250µA
/∆TJTemperature Coefficient of Breakdown — 0.11 — V/°C Reference to 25°C, ID = 1.0mA
Voltage
Static Drain-to-Source On-State — — 0.03 Ω VGS = 10V, ID = 28A
Resistance
Gate Threshold Voltage 2.0 — 4. 0 V VDS = VGS, ID = 250µA
Forward Transconductance 20 — — S ( )VDS =15V, IDS = 28A ➃
Zero Gate Voltage Drain Current — — 25 V
— — 250 VDS = 80V,
Gate-to-Source Leakage Forward — — 100 VGS =-20V
Gate-to-Source Leakage Reverse — — -100 VGS = -20V
Total Gate Charge — — 200 VGS =10V, ID = 28A
Gate-to-Source Charge — — 28 nC VDS = 80V
Gate-to-Drain (‘Miller’) Charge — — 94
Turn-On Delay Time — — 22 VDD = 50V, ID = 28A,
Rise Time — — 105 VGS = 10V, RG = 2.5Ω
Turn-Off Delay Time — — 75
Fall Time — — 60
Total Inductance — 6.8 — Measured from drain lead (6mm /
Input Capacitance — 2920 — VGS = 0V, VDS = 25V
Output Capacitance — 670 — pF f = 1.0MHz
Reverse Transfer Capacitance — 340 —
Ω
µA
nA
ns
nH
0.25in. from package ) to source
➃
= 100V ,VGS=0V
DS
VGS = 0V, TJ =125°C
lead (6mm/0.25in. from pacakge
Source-Drain Diode Ratings and Characteristics
Parameter Min Typ Max Units T est Conditions
I
Continuous Source Current (Body Diode) — — 35*
S
I
Pulse Source Current (Body Diode) ➀ — — 140
SM
V
Diode Forward Voltage — — 1.3 V Tj = 25°C, IS = 28A, VGS = 0V ➃
SD
t
Reverse Recovery Time — — 280 ns Tj = 25°C, IF = 28A, di/dt ≤ 100A/µs
rr
Q
* Current is limited by package
Reverse Recovery Charge — — 2.0 µCV
RR
t
Forward Turn-On Time Intrinsic turn-on time is negligible. Turn-on speed is substantially controlled by L
on
A
≤ 50V ➃
DD
Thermal Resistance
Parameter Min Typ Max Units Test Conditions
R
thJC
Note: Corresponding Spice and Saber models are available on the G&S Website.
For footnotes refer to the last page
2 www.irf.com
Junction-to-Case — — 1.0 °C/W
+ LD.
S
IRF5M3710
1000
100
10
D
I , Drain-to-Source Current (A)
1
0.1 1 10 100
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
4.5V
20µs PULSE WIDTH
T = 25 C
J
V , Drain-to-Source Voltage (V)
DS
°
Fig 1. Typical Output Characteristics
1000
1000
100
10
D
I , Drain-to-Source Current (A)
1
0.1 1 10 100
VGS
TOP
15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM
4.5V
4.5V
20µs PULSE WIDTH
T = 150 C
J
V , Drain-to-Source Voltage (V)
DS
°
Fig 2. Typical Output Characteristics
2.5
35A
I =
D
2.0
°
T = 25 C
100
10
D
I , Drain-to-Source Current (A)
1
4.0 5.0 6.0 7.0 8.0 9.0 10.0
Fig 3. Typical Transfer Characteristics
J
°
T = 150 C
J
15
V = 50V
DS
20µs PULSE WIDTH
V , Gate-to-Source Voltage (V)
GS
1.5
1.0
(Normalized)
0.5
DS(on)
R , Drain-to-Source On Resistance
0.0
-60 -40 -20 0 20 40 60 80 100 120 140 160
T , Junction Temperature( C)
J
Fig 4. Normalized On-Resistance
V =
GS
°
10V
Vs. Temperature
www.irf.com 3
Loading...