International Power Sources ZCA6C01PAPDI, ZCA6C01PAPDL, ZCA6C01PAPDM, ZCA6C16M, ZCA6C17I Datasheet

•

•

Input

AC Input Voltage • 85-264 VAC
Input Frequency • 47-63 Hz
DC Input Voltage • 48 VDC nominal (optional)
Power Factor • 0.99
Harmonic Current • Meets EN61000-3-2
Inrush Current • Limited to 30A peak
Input Protection • Internal 15A fuse

Output

Output Voltage • 1.8 VDC to 12 VDC
Output Power • 600W
Output Voltage Adj • ±5% min, See models chart
Minimum Load • 0 minimum load for all outputs
Line/Load Regulation • ±2% for V1, V2 and V3, ±3%

for V4 and V5

Ripple & Noise • >2.5V output: 50mV or 1% whichever

is greater <=2.5V output:
2% maximum

Transient Response • 4% max deviation, 300 µs recovery

time for a 25% load change
Temperature Co-eff. • 0.02%/°C
Hold Up Time • 20ms minimum
Remote Sense • Up to 0.25 V compensation on V1, V2

and V3
Overvoltage • V1, V2 and V3 only, recycle

Protection input to reset
Overcurrent • Standard with auto recovery

Protection
Overtemperature • Logic high signal for overtemp

Protection conditions
Current Sharing • ±10% for V1, V2 and V3 with

“H” option

General

Efficiency • 75% typical at full load
Power Density • 6.8 W/in

3

MTBF • 200,000 hrs per Bellcore
Isolation Voltage • 3000 VAC Input to Output

1500 VAC Input to Ground
500 VAC Output to Ground

Signals • PSU Enable, AC Fail, DC OK,

Global Inhibit, overtemp
LED Indicators • 2 status indicators
Size • 5.0” x 11.0” x 1.6”.
Weight • 3.3 lbs (1.5 kgs.)

Environmental

Operating • 0°C to 70°C, Full power to 50°C
Temperature derate from 50°C to 70°C

at 2.5%/°C
Cooling • 3 Internal ball bearing fans
Humidity • <95% RH, non-condensing
Storage Temperature • -40°C to +85°C

Safety and EMC

Safety Approvals • UL1950, CSA C22.2 No 950 per cUL,

EN60950 CE Mark LVD
EMI/EMC • EN61000-3-2, -3, EN55022 and FCC

20780 part 15J Class B conducted

with rack, Class A stand alone
Immunity & Surge • Meets EN61000-4-4, -5

600 Watts

ZC Series

Configurable Power Supply

Specification

•

Intelligent Design Quality Product

XPiQ inc.

Meets EN61000-3-2, -3

•

Up to 5 Outputs Plus 5V Standby

•

Low Voltage Outputs Down to 1.8V

•

Hot Swap or Chassis Mount

•

Oring Diodes On All Outputs

(Hot Swap Modules)

•

1U, 19” Rack Mount for 2 units

•

International Safety Approvals with CE (LVD)

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

ZC6.qxd 6/6/03 4:03 pm Page 1

Mechanical Details

CODE V1 V2 V3 CODE V4 CODE V5

01 1.8 V @ 70 A 2.5 V @ 50 A 12 V @ 10A PA +3.3 V @ 3 A PD +1.8 V @ 3 A
02 1.8 V @ 70 A 3.3 V @ 50 A 12 V @ 10A NA -3.3 V @ 3 A ND -1.8 V @ 3 A
03 1.8 V @ 70 A 5.0 V @ 50 A 12 V @ 10A PB +5.0 V @ 3 A PE +2.5 V @ 3 A
04 2.5 V @ 100 A - 12 V @ 10A NB -5.0 V @ 3 A NE -2.5 V @ 3 A
05 2.5 V @ 70 A 3.3 V @ 50 A 12 V @ 10A PC +12.0 V @ 3 A PF +3.3 V @ 3 A
06 2.5 V @ 70 A 5.0 V @ 50 A 12 V @ 10A NC -12.0 V @ 3 A NF -3.3 V @ 3 A
07 3.3 V @ 100 A - 12 V @ 10A - - PG +5.0 V @ 3 A
08 3.3 V @ 70 A 2.5 V @ 50 A 12 V @ 10A - - NG -5.0 V @ 3 A
09 3.3 V @ 70 A 5.0 V @ 50 A 12 V @ 10A - - PH +5.2 V @ 3 A
10 5.0 V @ 100 A - 12 V @ 10A - - NH -5.2 V @ 3 A
11 5.0 V @ 70 A 2.5 V @ 50 A 12 V @ 10A - - - ­12 5.0 V @ 70 A 3.3 V @ 50 A 12 V @ 10A - - - -

13 1.8 V @ 70 A 2.5 V @ 50 A 5 V @ 10A XX N/C PD +1.8 V @ 3 A
14 1.8 V @ 70 A 3.3 V @ 50 A 5 V @ 10A - - ND -1.8 V @ 3 A
15 2.5 V @ 100 A 5 V @ 10A - - - ­16 2.5 V @ 50 A 3.3 V @ 50 A 5 V @ 10A - - - ­17 3.3 V @ 100 A 5 V @ 10A - - - ­18 2.5 V @ 50 A 2.5 V @ 50 A 5 V @ 10A - - - -

ORDERING CODES ZC

1. For module codes 13 to 18, V4 may have an unregulated output but this output is not useable. XX is the only option code available for
V4 and only ±1.8V output is available for V5.

2. V4 is user adjustable from 2.8 VDC to 14.75 VDC codes define setpoint at factory.

3. V5 is user adjustable from 1.7 VDC to 8.12 VDC codes define setpoint at factory.

Notes

•

PART NUMBER ORDERING SCHEME

Series AC or DC Hotswap or V1-V3 Polarity V4 Output Polarity of V5 Output Option

Input Chassis Code of V4 Code V5 Code Code

ZC A6=AC H=Hotswap 01 to 18 P = Positive A to C P = Positive D to H L = Low Leakage

D6=DC C=Chassis N = Negative N = Negative I = I

2

C Module

M = Low Leakage

&12C

Example: ZCA6H06NCNG is AC input, Hotswap chassis with V1 = 2.5V/70A, V2 = 5V/50A, V3 = 12V/10A, V4 = -12V/3A, V5 = -5V/3A.

* Note:

Vertical blackplane mounting
may not allow for sufficient
airflow. Horizontal backplane,
or additional spacing with a
vertical backplane is
recommended.

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

ZC6.qxd 6/6/03 4:03 pm Page 2