International Communications Group 463091, 463093, 463095, 463092 User Manual And Installation Manual

Download

1.9-GHz Cordless Telephone

hone

User’s Guide and Installation Manual

System

Manual Number 500115

DECT Cordless Tele

International Communications Group, Inc.

www.icg.aero

INTERNATIONAL COMMUNICATIONS GROUP, INC.

1.9-GHz Cordless Telephone System

User’s Guide and Installation Manual

This manual includes coverage of the following model part number(s):

463091 463092 463093 463095

International Communications Group, Inc.

www.icg.aero

Aviation Cabin Handset

International Communications Group, Inc.

Newport News, VA 23603

Printed in the United States of America.

Cage Code 088F2

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

RECORD OF REVISIONS

REVISION ECN # COMMENTS/DESCRIPTION

---- Initial Release 07/10/2006

A 2193 Made changes and corrections to tables and drawings as per

the following DRs: 2918, 3159, 3227, 3250, 3252, 3435, 3436, 3438, 3439.

Proprietary Notice

This document and the information disclosed herein are proprietary data of the International Communications Group (ICG), Inc. Neither this document nor the information contained herein shall be used, reproduced, or disclosed to others without written authorization of ICG, except for installation of ICG equipment.

Notice–Freedom of Information Act 5-USC 553 and Disclosure of Confidential Information

Generally (18 USC 1905).

ICG is furnishing this document in confidence. The information disclosed herein falls within exemption (b)(4) of USC 552 and the prohibitions of 18 USC 1905. For further information, contact a Customer Support representative at ICG:

TELEPHONE:

Within the U.S. 1-800-279-1991 Select Customer Support option when prompted by

Outside the U.S. 1-757-947-1030 Select Customer Support option when prompted by

Direct Line 1-757-947-1060

FAX:

the Automated Attendant.

1-757-947-1036

DATE

REVISED

06/20/2007

Cordless Handset

iii

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

E-Mail:

techsupport@icg.aero

Calls received outside of normal business hours will be routed to an automated message and paging system, with the on-call Support Representative being notified of a Support situation. Customer Support is currently available 7 days per week between 0830 and 2100 E.S.T.

International Communications Group, Inc.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

SERVICE BULLETIN LIST

When a Service Bulletin is received for this unit, perform the instructions given, log it into the Service Bulletin List given below, and insert the Service Bulletin into this section to maintain a historical record.

SERVICE

BULLETIN NO.

TITLE

MANUAL

REVISION NO.

MANUAL REVISION

DATE

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Foreword

1. About This Manual

This manual presents the instructions for using and installing the ICG 1.9-GHz Cordless telephone handset on aircraft. For convenience and ease of use, this document is divided into two major sections. General information is in the User’s Guide; that information targets the casual user or cabin personnel. Detailed installation instructions can be found in the Installation Manual section; that information is geared to installation personnel.

A convenient reference guide to abbreviations, acronyms, and symbols used in the text is in the Glossary at the back of this document. Specialized terms will generally be written out everywhere in the text to avoid confusion. Standard, well-known electronic terms and circuit signal names will be abbreviated in the text without being defined. Also, a fairly comprehensive International Country Code Directory is at the back of this manual.

Customer Support at ICG welcomes your questions, comments, and corrections about this manual. In any correspondence, we would appreciate the publication number, equipment designations (found on the Cordless handset), document page or figure number, and your comments. Please send your communication to the following e-mail address:

techsupport@icg.aero

2. The Cordless Handset

The Cordless telephone is an aeronautical Communications Center handset designed to operate as a standard and familiar telephone. The Cordless is similar in operation to a cellular telephone in convenience and portability. The Digital Enhanced Cordless Telecommunications (DECT) cordless phone system is capable of interfacing to up to four discrete telephones to create a small phone network with a single telephone line. Each of the handsets is capable storing and retrieving profile information of the individual user including telephone directory, menu access, volume, ringer, and call logs. The base can be connected to two types of telephone subscriber lines with power source voltage of either 28 VDC of 115 VAC. Configurations of 2-wire or 4-wire systems are equipped with internal monitoring to facilitate access and control of the individual handsets. The handset cradle doubles as a battery-charging base when the phone is not in use. The handset is powered by three

1.2-V AAA NiMH rechargeable batteries. The base unit can be powered by 110/240 VAC at 40–400 Hz. or 28 VDC.

A Liquid Crystal Display (LCD) provides convenient operation and support for all types of calling services.

Cordless Handset

vii

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

3. Notices, Patches, and Updates

ICG has established on the corporate website (www.icg.aero) an area where clients can register to

receive advance information and notifications about changes to this unit. Clients who participate will also be able to download patches or future updates as they become available.

To take advantage of this free opportunity, simply fill out the requested information at the ICG website. You may remove your name from this service at any time by contacting ICG.

Privacy Statement

ICG will not sell, trade, or transfer user addresses or

information to any other sources.

4. Handling Electronics

As with any electronic component, the Cordless unit requires care when being handled. Always observe standard safety precautions to prevent personal injury or damage to the unit.

CAUTION

TURN OFF POWER BEFORE CONNECTING OR

REMOVING ANY COMPONENT TO AVOID DAMAGING

THE ELECTRONICS.

5. Advisories

Stray fingerprints, smudges, wire clippings, or metal shavings on outside surfaces should be removed with care. If cleaning is necessary, use only mild soap and a dampened cloth to swab the exterior surface.

Note

Use fluid sparingly to avoid letting any water, cleaners, or

solvents reach the internal components.

6. Cordless Models

The 1.9-GHz Cordless handset can be provided in the standard 2-wire configuration, standard 4-wire configuration, and with an optional attached magnetic stripe reader. All models are offered with either 28VDC or 115-VAC power options. Standard colors of the handset are white, grey, beige, or black with silver face. Custom colors are available upon request but require the customer to provide a standard “Pantone” color number. Both the handset and cradle unit can be painted. Typically, the base unit does not require a color c

hange as it is usually mounted in an area where it is not visible. ICG recommends that the

base unit not be painted in order to avoid RF interference by the paint.

Cordless Handset

viii

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

This document applies to all dash-number configurations of the Cordless handset,

Model Description

463091-XYZ Cordless Model w/Credit Card Reader and RJ-11 Jack in Cradle

463092-XYZ Standard Cordless Model

463093-XYZ Cordless Model w/ RJ-11 Jack in Cradle

463095-XYZ Cordless Model w/ Pop-Up Cradle Assembly

Note

The Cordless Phone System voltage and Telco

configuration are defined by the Base Unit.

For Example: P/N 463092-240 with base unit 463092-250 is a 28-Volt, 4-wire system.

Cordless Systems

-10Z -20Z -14Z -24Z

● ● ● ●

●

X = Power (Applies to base unit and system only)

Cordless Component Parts

463092-112/212 Cordless Handset 463092-112/212 Cordless Cradle

463092-130 Cordless Base, 115 VAC, 2 Wire 463092-230 Cordless Base, 28 VDC, 2 Wire 463092-150 Cordless Base, 115 VAC, 4 Wire 463092-250 Cordless Base, 28 VDC, 4 Wire

1 115 VAC 2 28 VDC

Y = Part

1 2-Wire System 2 Handset (ECHS 2507 A) 3 Cradle (ECHS 2507B) 4 4-Wire System 5 Base Unit, 4-Wire

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Z= Color

0 Black/Silver 1 White 2 Beige 3 Grey C Custom number

Extender Cable Connector Kit: P/N 500480 extends the cradle-to-base cable. (Cable not included).

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TABLE OF CONTENTS SECTION PAGE

Foreword....................................................................................................................................................vii

1. About This Manual ...............................................................................................................................vii

2. The Cordless Handset .........................................................................................................................vii

3. Notices, Patches, and Updates...........................................................................................................viii

4. Handling Electronics ...........................................................................................................................viii

5. Advisories............................................................................................................................................viii

6. Cordless Models .................................................................................................................................viii

User’s Guide................................................................................................................................................1

SYSTEM OVERVIEW...............................................................................................................................1

BASIC USE...............................................................................................................................................3

DISPLAY...................................................................................................................................................4

UP&DOWN ...............................................................................................................................................4

1. Making a Call ........................................................................................................................................4

2. Answering a call .................................................................................................................................... 4

3. Ending a Call......................................................................................................................................... 4

4. Pausing a call........................................................................................................................................ 4

5. Adjusting Ear-Piece Volume .................................................................................................................5

6. Redialing a Number ..............................................................................................................................5

7. Dialing from the Telephone Book.......................................................................................................... 5

8. Viewing the Log of Calls........................................................................................................................ 5

9. Locking the Keypad............................................................................................................................... 5

10. Entering Characters Using the Keys ............................................................................................. 5

11. Changing to Upper-Case Text ......................................................................................................5

12. Adding/Replacing Batteries in DECT Handsets............................................................................ 6

SPECIAL USE ..........................................................................................................................................7

1. Clearing the Call Log............................................................................................................................. 7

2. Clearing the Redial List ......................................................................................................................... 7

3. Changing the Ringing Pattern............................................................................................................... 7

4. Adjusting the Ring Level .......................................................................................................................7

5. Using Key Click ..................................................................................................................................... 8

6. Using Auto Answer................................................................................................................................ 8

7. Changing the Handset Language ......................................................................................................... 8

8. Changing Country Settings ................................................................................................................... 8

9. Setting the Time and Date ....................................................................................................................9

10. Assigning the Handset a Name..................................................................................................... 9

11. Registering Additional Handsets................................................................................................... 9

12. Manually Registering An Additional Handset.............................................................................. 10

13. Deregistering a Handset .............................................................................................................10

Installation Manual....................................................................................................................................11

INTRODUCTION.....................................................................................................................................11

1. General................................................................................................................................................11

2. Planning ............................................................................................................................................. 11

(A) Preparation..........................................................................................................................11

(B) Unpacking ...........................................................................................................................11

(C) Cleaning .............................................................................................................................. 12

3. Abbreviations and Acronyms ............................................................................................................. 12

4. Advisories ..........................................................................................................................................12

5. Related Documents ........................................................................................................................... 13

Cordless Handset

xiii

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

DESCRIPTION........................................................................................................................................15

1. Basic Design .......................................................................................................................................15

2. Cordless Standard Assembly.............................................................................................................. 16

(A) The Handset........................................................................................................................16

(B) Charging Cradle .................................................................................................................. 16

(C) Base Unit............................................................................................................................. 16

(D) Magnetic Stripe Reader ......................................................................................................16

INSTALLATION PROCEDURES ...........................................................................................................17

1. Planning ............................................................................................................................................. 17

2. Connections....................................................................................................................................... 17

3. Charging Cradle ..................................................................................................................................17

TESTING THE UNIT...............................................................................................................................19

1. Introduction ........................................................................................................................................ 19

2. Making an Outbound Call .................................................................................................................. 19

3. Answering an Inbound Call................................................................................................................ 19

4. Making a New Call............................................................................................................................. 19

FITS AND CLEARANCES......................................................................................................................21

SYSTEM SPECIFICATIONS..................................................................................................................27

1. Purpose..............................................................................................................................................27

2. Product Definition ..............................................................................................................................27

3. Specifications..................................................................................................................................... 27

SPECIAL TOOLS, FIXTURES, AND EQUIPMENT...............................................................................29

1. Introduction ........................................................................................................................................ 29

2. Test Setup and Calibration ................................................................................................................ 29

TROUBLESHOOTING THE SYSTEM ...................................................................................................31

1. Introduction ........................................................................................................................................ 31

2. Fault System Quick Reference .......................................................................................................... 31

WIRING DIAGRAMS..............................................................................................................................35

1. Aircraft Power...................................................................................................................................... 35

2. Physical Connectivity 4 WIRE CORDLESS TO MAGNASTAR..........................................................36

3. Telephone Circuit Connection 2-Wire Telephony ............................................................................... 38

4. Telephone Circuit Connection 4-Wire Telephony ............................................................................... 38

5. Cradle Connections............................................................................................................................. 40

(A) Handset ............................................................................................................................... 40

(B) Cordless with Magnetic Stripe Reader................................................................................ 40

(C) Extender Cable: Cradle to Base......................................................................................... 41

AIR WORTHINESS/RMA PROCEDURE...............................................................................................47

1. Air Worthiness ...................................................................................................................................47

2. ICG Customer Support for Returning Cordless Units........................................................................ 47

3. ICG Customer Service Contact Information ...................................................................................... 47

4. Packaging For Shipment ...................................................................................................................48

5. Package Markings ............................................................................................................................. 48

6. Shipping ............................................................................................................................................. 48

7. Notification ......................................................................................................................................... 48

8. Website for Notices, Patches, and Updates to the Firmware............................................................ 48

GLOSSARY............................................................................................................................................49

INTERNATIONAL COUNTRY CODE DIRECTORY..............................................................................51

Cordless Handset

xiv

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

LIST OF FIGURES

Figure 1. The standard Cordless unit

Figure 2. The DECT Cordless display icons ................................................................................................ 2

Figure 3. The DECT Cordless handset........................................................................................................ 3

Figure 4. The standard Cordless handset and cradle................................................................................ 15

Figure 5a. The cordless handset ...............................................................................................................21

Figure 6. 28-VDC 4-wire unit......................................................................................................................23

Figure 7. 28-VDC 2-wire unit.......................................................................................................................24

Figure 8. 115-VAC4-wire unit..................................................................................................................... 25

in its cradle........................................................................................ 1

Figure 9. 115-Volt AC 2-wire unit............................................................................................................... 26

LIST OF TABLES

Table 1. Handset buttons and functions ......................................................................................................4

Table 2. The DECT Cordless menu structure ......................................................................................6

Table 3. Quick Help....................................................................................................................................31

Table 4. Display messages........................................................................................................................ 33

Table 5. Audio Alerts..................................................................................................................................34

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

User’s Guide

SYSTEM OVERVIEW

The Digital Enhanced Cordless Telecommunications telephone is a multifunctional aeronautical Communications Center handset that is compatible with standard aircraft power sources, 28 VDC or 115 VAC. The handset is available with 2- and 4-wire Cabin Telephony Unit (CTU) interfaces. This unit also features uncomplicated menus and functions that are easy to learn or understand.

Figure 1. The standard Cordless unit

in its cradle

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

The DECT phone base station can register up to four handsets. They can be used for intercom calls as well as for forwarding calls between handsets. Incoming calls can be answered by any of the registered handsets. Any entries made to the telephone book will automatically be shared between the handsets.

Figure 2. The DECT Cordless display icons

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

BASIC USE

Note

Throughout this section, the bulleted statements ()

indicate specific instructions for

performing an action.

The Cordless telephone is similar in operation to a standard cellular handset. Functions such as initiating calls, answering calls, and disconnecting calls are accomplished using familiar procedures. The handset also features distinct special-function keys to provide enhanced features such as flash transfer, pause, telephone book access, calls to other aircraft handsets, a log of incoming calls, and access to programming menus.

Figure 3. The DECT Cordless handset

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TABLE 1. HANDSET BUTTONS AND FUNCTIONS

BUTTON FUNCTION BUTTON FUNCTION

DISPLAY

DEL

TELEPHONE BOOK

INT

PHONE KEY

PAUSE

Displays the status of your handset.

Use to delete digits (press and release) or cancel operation (press and hold).

Use to open the telephone book to find numbers or add, edit, and delete entries.

Press to make calls to additional handsets (internal).

Use for making and answering calls.

Press and hold for pause, press and release for *.

1. Making a Call

 Remove the handset from the cradle and press the <§> button to place a call.

 Dial the destination telephone number and wait for the call to connect. Alternatively, you can

dial the telephone number first, then press the < portability, so it can remain on a desk or other convenient location for easy access.

UP&DOWN

LOG

RED PHONE

ON/OFF

FLASH

§> button. This phone is designed for

Use to navigate through handset functions.

Press to see list of incoming calls.

Press to end call.

Press to turn phone on or turn phone off.

Use to enter menu and to select and confirm.

Press and hold for Flash, press and release for #.

2. Answering a call

The telephone handset will ring on an inbound call.

 To answer the call, simply remove the handset from the cradle.  Press the <§> button and the calling party will be on the line.

3. Ending a Call

 Press the red <§> button to end a call and return the handset to a ready state.

4. Pausing a call

 Press the <#R> button and hold for one second to place a call on hold and mute the audio so

no communication is possible between the handset and the other party.

 To release the hold feature and restore the call, press the <#R> button again.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

5. Adjusting Ear-Piece Volume

 Press <OK> (below the liquid crystal display (LCD) 3 times. Use <> or <> to raise or

lower the volume.

 Press <

 Press the red <

OK> to save the setting.

§> button to cancel the setting.

6. Redialing a Number

 When the unit is in the ready state, press the <> or <> buttons to scroll through a list

of previous calls.

 Press the <

§> button to place the call.

7. Dialing from the Telephone Book

 Press <> at the left just below the LCD.

 Use the <

 Press the <

> or <> buttons to scroll through your telephone list.

§> button to make the call.

8. Viewing the Log of Calls

 Press <LOG> at the right just below the LCD.

 Press the <

> or <> buttons to scroll through a list of calls.

9. Locking the Keypad

 Press <OK>.

 Then press <

 Repeat to unlock.

*P>.

10. Entering Characters Using the Keys

 Press the button with the letter you want the same number of times as the position of the

letter on the keypad (for example, press < one time for the letter “M.”)

ABC

> 2 times for the letter “B.” Press <6

11. Changing to Upper-Case Text

 Press and hold <*P> to change to upper case.

 Release to return to lower case.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

MNO

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

12. Adding/Replacing Batteries in DECT Handsets

 Remove the handset from its charger or base.

 Slide open and remove the casing on the back of the handset.

 Remove the existing batteries (if replacing old ones).

 Insert 3 Varta-T398 (or equivalent) 1.2-V AAA rechargeable NiMH batteries, orienting the

positive terminals as indicated on the casing.

 Replace the battery casing by sliding it back into place until it clicks.

 Return the handset to its charger and allow the unit to recharge for 14 hours.

TABLE 2. THE DECT CORDLESS MENU STRUCTURE



Press <OK> to enter the menu.

1 > Tone

2> Handset name

3 > Auto answer

4> Language

5> Registration

6> Time & Date

1 > Handset volume 2 > Ring level 3 > Ring pattern 4 > Key click 5 > Online tone

1 > English 2 > Dansk 3 > Norsk 4 > Svenska

1 > Register 2 > Deregister

1 > Automatic 2 > Manual 3 > Format

1 > External 2 > Internal

1 > Dereg. self 2 > Int 2 3 > Int 3 4 > Int 4

1 > 24 hour 2 > 12 hour 3 > mm/dd 4 > dd/mm

1 > Melody 1 2 > Melody 2 3 > Melody 3 4 > Melody 4

*> Key loc

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

SPECIAL USE

The Cordless handset operates much like a standard cellular telephone. Functions such as initiating calls, answering calls, and disconnecting calls are accomplished using familiar procedures. Specialfunction keys are provided to add conveniences and added features:

1. Clearing the Call Log

 Open the call log by pressing <LOG> at the right just below the LCD.  Press <OK> to call up the Store, Delete Entry, and Delete All options.  Scroll and press <OK> to delete all.  Press <OK> to confirm.

2. Clearing the Redial List

 Open the redial list by pressing the <> or <> buttons.  Press <OK> to call up the Store, Delete Entry, and Delete All options.  Scroll and press <OK> to delete all.  Press <OK> to confirm.

3. Changing the Ringing Pattern

 Press <OK> 2 times.

 Press the <> button 2 times.  Press <OK>.

 Scroll to choose Net, External, or Internal.

 Press <OK> after making your choice.

 Scroll to choose 1–5 tones.

 Press <OK> to save your choice.

4. Adjusting the Ring Level

 Press <OK> to enter the menu.  Select 1>Tone.  Choose 2>Ring Level.

 Press the <> or <> buttons to adjust the volume.  Press <OK> to store your choice.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

5. Using Key Click

 To set the keyboard so that each key emits a click when pressed, press <OK> to enter the

menu.

 Select 1>Tone.  Select 4> Key Click.

 Press <OK> to store the change.

 Follow the same procedure to cancel the key click mode.

6. Using Auto Answer

The Cordless telephone can be set for call answering by simply lifting the handset from the cradle.

 To activate auto answer, press <OK> to enter the menu.  Select 3>Auto Answer.

 Press <OK> to select that change.

7. Changing the Handset Language

 The handset is programmed to accommodate a number of languages. To change language

settings, press <

OK> to enter the menu.

 Select 4>Language.  Use the <> or <> buttons to find the language you prefer.  Press <OK> to select that change.

Note

If the handset language is changed accidentally to one

you do not understand, you can enter the language

menu by pressing <OK> and 4

your preferred language and press <OK> to save your

selection.

8. Changing Country Settings

 Press <OK> to enter the menu.

 Scroll to find 8>Country.  Press <OK> to enter.

GHI

. Then, scroll to find

 Scroll through the list of countries.

 Press <OK> to set your country preferences.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

CHANGE THE COUNTRY SETTING ONLY IF THE

TELEPHONE IS BEING TAKEN TO ANOTHER

COUNTRY. IN THAT CASE, THE HANDSET MUST BE

CONNECTED TO AN ORDINARY TELEPHONE LINE.

9. Setting the Time and Date

 Press <OK> to access the menu.  Find the menu 6>Time & Date.  Press <OK>.  Choose 3>Format in the Time & Date menu to alter the format from 12 to 24 hours or mm/dd

to dd/mm.

 Scroll through the format options.

CAUTION

 Press <OK> to save your selection.

10. Assigning the Handset a Name

Naming the handset can be useful when adding an extra handset to the base. This way, you can easily identify the various handsets when you make internal calls. The name of the handset will be dis

played when the handset is not in use.

 To set the name of the handset, press <OK> to enter the menu. Press .  Select 2>Handset Name.  Press <OK>.

 Use the keypad to enter a name.

 Press <OK> to save.

11. Registering Additional Handsets

You can register up to four handsets to the base.

 Insert batteries into the additional unit as discussed above.

 Place the handset in the charger and wait for approximately 10 minutes for the handset to

charge sufficiently to be registered to the base.

 Listen for the confirming tone when the handset is ready for use. The display will also say

“Ready.”

 Allow 14 hours for full battery charging.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

12. Manually Registering An Additional Handset

 To register a new handset manually, you must prepare the base station. To do so, press and

hold the page button for 5 seconds. When the charge light flashes, the base is ready to register your handset.

 Press <OK> to access the menu.  Select 5>Registration, then 1>Register. If successful, you will receive a prompt to enter the

handset name.

 Enter the name and press <OK> to save or press and hold <DEL> to leave the menu.

13. Deregistering a Handset

 Press <OK> to enter the menu.  Select 5>Registration, then 2>Deregister.

 Press the <> or <> buttons to select which handset to deregister.  Press <OK> to confirm.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Installation Manual

INTRODUCTION

1. General

This section presents instructions for installing the International Communications Group, Inc. (ICG) Cordless handset. It offers special features while replicating the convenience and simplicity of a conventional telephone.

Note

The material in this document may be updated at any

point. Therefore, before installing the

Cordless, please check with ICG at www.icg.aero to

determine whether revisions have been issued to all or

parts of this installation manual.

The Cordless unit meets all operational and environmental standards for telephonic devices, as indicated in the section, System Specifications. In case of question regarding these issues, contact ICG at the following address:

Customer Support International Communications Group, Inc. Newport News, VA 23603 Phone: 1-757-947-1030

2. Planning

(A)

Preparation

Review industry-established electronic equipment practices to prepare for installing the Cordless telephone. Those practices include reviewing the procedures in this manual; carefully choosing the equipment locations; checking for adequate space around the connectors and cabling; and ensuring that the target location is free of all water, spray, lubricants, or other stray fluids.

(B)

Unpacking

As with any electronic device, unpack the unit carefully and reserve the shipping material and packaging, if possible, in case a future return is required. If the equipment appears damaged upon initial visual inspection, report the damage immediately to ICG and use the original shipping material to return the system to ICG. Instructions on the return procedure can be found in the section, Air Worthiness/RMA Procedure.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Stray fingerprints, smudges, wire clippings, metal shavings, or other debris on outside surfaces of the handset should be removed upon completion of installation or repair work.

If cleaning is necessary, use only mild soap and limit water amount to avoid letting any moisture reach the internal components.

Lightly moisten a cloth and lightly swab the exterior surface in need of cleaning.

3. Abbreviations and Acronyms

A convenient reference guide to abbreviations, acronyms, and symbols used in the text can be found in the Glossary at the back of this document. Specialized terms will generally be written out everywhere in the text to avoid confusion. Standard, well-known electronic terms and circuit signal names are abbreviated in the text without also being written out.

4. Advisories

WARNING:

CAUTION:

Observe standard safety precautions and wear SAFETY GLASSES AND OTHER proper safety gear to prevent personal injury during installations.

TURN OFF POWER BEFORE DISCONNECTING ANY COMPONENT FROM WIRING. DISCONNECTING THE COMPONENT WITHOUT TURNING POWER OFF MAY CAUSE VOLTAGE TRANSIENTS THAT CAN DAMAGE THE COMPONENT.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

CAUTION: ELECTRO-STATIC-SENSITIVE DEVICES ARE SUBJECT TO DAMAGE BY EXCESSIVE LEVELS OF VOLTAGE AND/OR CURRENT, JUST AS ARE MORE CONVENTIONAL SEMICONDUCTOR DEVICES. HOWEVER, THE PRECAUTIONS NORMALLY USED TO PROTECT SEMICONDUCTORS ARE NOT SUFFICIENT FOR THE PROTECTION OF ELECTROSENSITIVE DEVICES BECAUSE OF THEIR VERY HIGH ELECTRICAL RESISTANCE. THE LOWENERGY SOURCE THAT MOST COMMONLY DESTROYS THESE DEVICES IS THE HUMAN BODY WHICH, IN CONJUNCTION WITH NONCONDUCTIVE GARMENTS AND FLOOR COVERINGS, GENERATES AND RETAINS STATIC ELECTRICITY. TO PROTECT ELECTROSENSITIVE DEVICES ADEQUATELY, THE DEVICE AND EVERYTHING THAT CONTACTS IT MUST BE BROUGHT TO GROUND POTENTIAL BY PROVIDING A CONDUCTIVE SURFACE AND DISCHARGE PATHS.

THE FOLLOWING PRECAUTIONS MUST BE FOLLOWED before installing the CORDLESS:

DE-ENERGIZE OR DISCONNECT ALL POWER AND SIGNAL SOURCES AND LOADS BEFORE INSTALLING THE CORDLESS.

PLACE THE COMPONENT ON A GROUNDED, CONDUCTIVE SURFACE.

GROUND THE INSTALLER THROUGH A CONDUCTIVE WRIST STRAP OR OTHER DEVICE USING A 470-KILOHM OR 1-MEGOHM SERIES RESISTOR TO PROTECT THE EQUIPMENT.

GROUND ANY ELECTRICAL TOOLS, SUCH AS SOLDERING EQUIPMENT THAT WILL CONTACT THE COMPONENT. CONTACT WITH THE OPERATOR'S HAND PROVIDES A SUFFICIENT GROUND FOR TOOLS THAT ARE OTHERWISE ELECTRICALLY ISOLATED.

WHEN ESDS DEVICES AND ASSEMBLIES ARE NOT IN THE COMPONENT, THEY SHOULD BE ON THE CONDUCTIVE WORK SURFACE OR IN CONDUCTIVE CONTAINERS. WHEN A DEVICE OR ASSEMBLY IS INSERTED OR REMOVED FROM A CONTAINER, THE OPERATOR SHOULD MAINTAIN CONTACT WITH THE CONDUCTIVE PORTION OF THE CONTAINER. DO NOT USE PLASTIC BAGS UNLESS THEY HAVE BEEN IMPREGNATED WITH A CONDUCTIVE MATERIAL.

DO NOT HANDLE ESDS DEVICES UNNECESSARILY OR REMOVE THEM FROM THEIR PACKAGES UNTIL ACTUALLY USED OR TESTED.

5. Related Documents

This document applies to all dash-number configurations of the Cordless handset series, P/N 463091-XYZ, 463092-XYZ, 463093-XYZ, and 463095-XYZ.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

DESCRIPTION

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 4. The standard Cordless handset and cradle

1. Basic Design

The 1.9-Ghz Cordless telephone is designed to provide the Aeronautical Industry with an aircraftapproved cordless handset. Based on the successful DECT 1.9-GHz spread spectrum technology, the 1.9-GHz Cordless device has been modified to meet the more demanding requirements and certifications required for aircraft operation. Modifications include a custom-designed fire-retardant latching cradle, fire-retardant base unit enclosure, and special connectors.

The handset has two special buttons: < call, and the red <§> button, which is used to terminate a call and hang up the telephone. Any time

a user replaces the telephone into the cradle, the telephone will hang up or connect the line

regardless whether the red < the call will be answered as soon as the user removes the handset from the cradle.

Operation is identical for either the 2-wire or 4-wire model of the Cordless handset.

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

§> button was pressed. If the telephone is in the Auto Answer mode,

§> which is used to place a call or to answer an inbound

Cordless Handset

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

2. Cordless Standard Assembly

The 1.9-GHz Cordless is functionally divided into 3 standard assemblies:

Handset Charging Cradle Base Unit

Additionally, an optional magnetic stripe reader can be added to provide Credit Card entry for restricted services.

(A)

The Handset

The 1.9-GHz. Cordless is the standard DECT handset modified to automatically shut off to avoid battery discharge when the handset is out of the charg power has been shut off. This “auto shut off” circuit turns the handset off after 5 hours of absence of charging current, providing that the handset has not been in use in the previous 5 hours.

(B)

Charging Cradle

The 1.9-GHz Cordless telephone has a custom manufactured cradle that secures the handset and provides charging current to the handset batteries. This device is constructed out of a fireretardant polycarbonate material in an ergonomic and eloquent design. In its standard configuration, it is connected to the base unit by a 90-cm. pre-wired cable and connector.

er for extended periods or the aircraft

(C)

(D)

Base Unit

The 1.9-GHz Cordless base unit provides the transceiver functions to communicate with the handset as well as power to the charging cradle. It also provides for connection to a CTU or communications transceiver over a standard 2-wire telephone circuit or 4-wire telephone circuit with discreet hook-and-ring signals. The base unit is constructed out of the same fire-retardant material as the cradle assembly. The base comes in both 28-VDC and 115-VAC models that permit connection to convenient aircraft power.

Magnetic Stripe Reader

An optional magnetic stripe reader can be added to support applications requiring entry of Credit Card information. The magnetic stripe reader reads the standard ISO Track II of a Credit Card and converts the information to Dual-Tone Multi-Frequency (DTMF) tones that are sent over the telephone circuit. The magnetic stripe reader can be configured to provide the Credit Card information in the format required by the service provider.

Note

The Credit Card format varies by communication services and service

providers. Notify ICG of the intended use and communications provider

to ensure correct programming of the Credit Card format.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

INSTALLATION PROCEDURES

1. Planning

The ICG Cordless base unit and the charging cradle are easy to install and test. However, both advance planning and review of this document are recommended before an installation.

Wiring diagrams and dimensional drawings are available in the “System Specifications” section of this manual..

A regular toolkit is sufficient for attaching all hardware to the aircraft.

2. Connections

The Cordless telephone base unit is typically mounted in the aircraft cabin that is out of site, either in a closet or behind a bulkhead or headliner. Considerations for mounting should be as follows:

(A) In a pressurized and temperature-controlled area.

(B) Within 35.4 inches (90 cm) of the charging cradle. (An extension cable, cradle-to-base unit,

can be assembled for distances greater than 35.4 inches or 90 cm.)

assemblies. The base unit should not be mounted in a metal enclosure or surrounded by metal or any material that attenuates RF frequencies.

(D) Away from micro wave ovens or other RF transmission equipment. The base unit should not

be mounted within about 10 ft. (3 m) of a microwave oven.

3. Charging Cradle

The charging cradle can be mounted vertically on a bulkhead or divider or it can be mounted horizontally in a drink rail or furniture assembly. Mounting considerations are as follows:

(A) The cradle assembly should be mounted away from metal and should be in an area

permitting unobstructed communications with the base unit.

(B) The cradle assembly should not be mounted within 24 inches (60 cm) of a microwave oven.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TESTING THE UNIT

1. Introduction

The ICG Cordless handset is easy to install and test. However, both advance planning and review of this document are recommended before beginning an installation.

Note

Throughout this section, the bulleted statements ()

indicate specific instructions for

performing an action.

2. Making an Outbound Call

 Remove the handset from the cradle.  Press the <§> button

 Dial the destination telephone number and wait for the call to connect.

3. Answering an Inbound Call

The telephone handset will ring on an inbound call.

 Remove the handset from the cradle.  Press the <§> button. The calling party will be on the line.

4. Making a New Call

The ICG Cordless telephone has a red button labeled <§>. It obviates the requirement to hang up the handset after every call.

 Press the red <§> button to disconnect a call in progress.

 Dial the number.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

FITS AND CLEARANCES

Figure 5a. The cordless handset

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 5b. The cordless handset

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 6. 28-VDC 4-wire unit

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 7. 28-VDC 2-wire unit

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 8. 115-VAC4-wire unit

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Figure 9. 115-Volt AC 2-wire unit

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

SYSTEM SPECIFICATIONS

1. Purpose

This section presents the specifications for Cordless handset.

2. Product Definition

The ICG Cordless telephone offers the convenience of a cellular phone and the special programming capabilities for aeronautical use. The cradle and power supply can be mounted anywhere and the handset can be conveniently moved about the aircraft. The telephone can be programmed for familiar services but also offers the option of changing the language to suit diverse users.

3. Specifications

DIMENSIONS: Base Unit: Length 8.0 in. (205 mm)

Width 5.0 in. (125 mm) Height 2.2 in. (56 mm)

Cradle Unit: Length 7.0 in. (180 mm) Width 2.9 in. (74 mm) Height 2.2 in. (56 mm)

WEIGHT:

Handset w/ batteries 463092-110 Cradle w/ cable 463092-120 Cradle w/ Mag-reader 463091-120 Base unit, 2 W, 28 VDC 463092-230 Base unit, 2 W, 115 VAC 463092-130 Base unit, 4 W, 28 VDC 463092-250 Base unit, 4 W, 115 VAC 463092-150

LIMITATIONS FOR OPERATIONS: Operating temperature 32°F (0°C) to 131°F (+55°C)

LIMITATIONS FOR HANDLING: Not applicable

5.3 oz (165 grams)

10.7 oz (333 grams)

15.7 oz (488 grams)

15.9 oz (495 grams)

15.1 oz (470 grams)

16.1 oz (500 grams)

24.1 oz (750 grams)

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

DEVIATIONS FROM SPECIFICATION: None

POWER REQUIREMENTS: 115 VAC, 10 VA

28 VDC, 20 VA

ALTITUDE: 15,000 ft. TESTS CONDUCTED: EMI/RFI DO-160E Sec. 21.4, cat M

FIRE RETARDANCY (Cradle and Base Unit)

BATTERIES (Handset): Varta T398 (or equivalent) 1.2-V AAA Rechargeable

(3 Each) NiMH 750mAh, slow charge only 70mA for 14 hrs.

CAUTION

USE ONLY THE RECOMMENDED BATTERIES WITH

THIS HANDSET. USE OF IMPROPER BATTERIES

MAY RESULT IN INJURY TO OPERATOR.

MODELS 463092-100/200: CTU Interface

Tip and Ring 24–48-VDC Loop Battery, 20 mA Audio Impedence 600 Ω

MODELS 463092-140/240: CTU Interface

Audio Impedence TX 600 Ω

Audio Impedence RX 600 Ω Hook Circuit/Open Collector 100 mA Max. Ring signal, 12 VDC Requires Ground at ring cadence

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

SPECIAL TOOLS, FIXTURES, AND EQUIPMENT

1. Introduction

No special tools are required to install the Cordless telephone unit.

2. Test Setup and Calibration

Refer to the instructions and guidance presented in the Testing section of this manual. Test in accordance with the Aircraft Test Plan (ATP

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TROUBLESHOOTING THE SYSTEM

1. Introduction

The discussion that follows in this section provides procedures to aid the technician in diagnosing most Cordless handset equipment problems. For problems with no remedy presented in this section, replace the handset with an equivalent model and part number.

2. Fault System Quick Reference

TABLE 3. QUICK HELP

Problem Possible Cause Solution

The handset is not registering.

• The base is not connected.

• There are no batteries in

the handset or the batteries are dead.

• Make sure that the power supply is

properly connected to the base. Power must be switched on.

• Make sure that the rechargeable

batteries (included) are fitted in the handset correctly. Place the handset in the base station correctly and wait approximately 60 seconds before trying to register again.

No display is showing.

Nothing happens when you push any buttons.

There is no connection between the handset and the base station.

The handset on the base does not charge.

The batteries are dead. Charge or replace the batteries.

The key lock may be activated. See if the key lock icon is lit. If so, press

*P> to switch the key lock

• Are you out of range of the

base station?

• The handset is not

registered.

• The base station is not

connected to power.

• Is the handset placed in

the base properly?

• Are the batteries inserted

correctly?

<OK> and <

off.

• Move closer to the base station.

• Register the handset.

• Check that the main power is

connected correctly.

• Make sure that the handset is

placed on the base or in the charger correctly.

• Check that you have put the

batteries in the right way.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

The handset does not ring.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

• The handset ringer may be

switched off.

• The handset may be too

far away from the base.

• Cancel ringer off.

• Return to the base.

You cannot dial external numbers.

The incoming caller’s number is not displayed.

You cannot make a call to another handset.

• The telephone line may be

damaged.

• The telephone line may be

busy.

• The caller’s number has

been withheld.

• You do not subscribe to a

Caller ID service.

• The other handset is not

registered.

• The handset is out of

range.

Note

The handset cannot be turned off.

• Contact your operator.

• Make sure the telephone line is not

occupied.

• The caller has to allow the number

to be sent.

• Contact your telephone operator for

details.

• Register the handset with the base

station.

• Move closer to the base to regain

service.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TABLE 4. DISPLAY MESSAGES

Not registered. Place in base

Ready

Charging Battery low.

Place in charger Ready

Keys locked Ready

Line in use Ready

Both in use Ready

10 calls/3 new

The handset is not yet registered to the base. The display will say “Ready” upon successful registration.

The handset is ready for receiving and placing calls. If you have entered a handset name, this will be displayed instead.

The batteries are being charged.

The batteries are low and need charging.

The key pad is locked and the buttons cannot be activated. Unlock to use the handset.

The telephone line is occupied by another handset.

Both lines are busy.

You have had 10 incoming calls and 3 new calls in the log remain to be viewed.

Ext Talk 1:32:56 Mom

Ext Talk 1:32:56 Battery low

Ext talk 1:32:56

You have talked to Mom for 1 hour, 32 minutes, and 56 seconds.

The batteries are low and need charging. Place in the base or charger. This will also end the call.

The microphone is muted.

Mic mute Out of service

The handset is either out of range from the base or power has been disconnected. Return to the base and wait for the handset to regain service; also check power connections.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

TABLE 5. AUDIO ALERTS

• Positive confirmation tone.

• Negative confirmation tone.

• A one-time triple beep means that the handset is too far away from

the base (out of range)

• A double beep indicates that the batteries are low and must be

charged.

• When the handset is placed in the base, you will hear a single

beep. The handset is now being charged.

• Call waiting.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

WIRING DIAGRAMS

The base unit has three primary connections: (1) aircraft power, either 28 VDC or 115 VAC, (2) telephone connection to a CTU or communications transceiver, and (3) connection to the charging cradle either using the pre-wired cable or with an extension cable.

1. Aircraft Power

Standard aeronautical wiring practices should be utilized in connecting power to the base unit.

Recommended Cable: three-conductor stranded overall shield 18 AWG

Circuit Breaker: 2 Amps 28 VDC 1 Amp 115 VAC

Base Unit (J1) Aircraft Power 28 VDC, 2

Wire

1 +28 VDC 115 VAC Hot 2 -28-VDC Return Neutral 3 Airframe Ground Aircraft Ground

Aircraft Power 115 VAC

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

2. Physical Connectivity 4 WIRE CORDLESS TO MAGNASTAR

CBDR-2 Signal Name

CBDR-2 Source Pin (J5: Analog Interface Port)

Cable Type Cordless Base

Unit (J2: Line Interface

Cordless Base Unit Signal Name

Connector)

Speaker_Audio_(+)

Speaker_Audio_(-)

J5/19

J5/20

Aud_Shld Shield Braid

#22 AWG Shielded, Twisted Pair

#22 AWG

J2/2

J2/3

Audio Hi

Audio Lo

Connect to J5 connector backshell

Mic_Audio_(+)

Mic_Audio_(-)

J5/4

J5/5

#22 AWG Shielded, Twisted Pair

J2/4

J2/5

Mic_Shld #22 AWG Shield Braid

Mic Hi

Mic Lo

Connect to connector backshell

Hook Switch J5 / 17 #22 AWG

J2/7 Hook Switch

Shielded

Status_A J5/7 #22 AWG

J2/6 Ringer In

Shielded

Audio_Sel_0 J5/22

#22 AWG Connect to J5/24 (Config_Gnd)

Pwr_Rtn J5/18 #22 AWG

Shielded

J2/8

Ground

Note

Connecting Audio_Sel_0 to configuration ground

configures the CBDR-2 operating mode to

600_OHM_AUDIO.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

3. Telephone Circuit Connection 2-Wire Telephony

A standard telephone circuit must be connected to the base unit. The 1.9-GHz cordless telephone will operate correctly with any telephony circuit that provides a standard tip-and-ring connection with 24-VDC to 48-VDC loop battery and a high-voltage AC ring signal.

Recommended Cable: two-conductor stranded

overall shield

20–24 AWG

Base Unit (J2)

Signal

CTU/Transceiver

Connection

1 Telephone Circuit TIP Telephone Circuit TIP 2 Shield Aircraft /Chassis Ground 3 Telephone Circuit RING Telephone Circuit RING

4. Telephone Circuit Connection 4-Wire Telephony

For the 4-wire cordless models, several additional circuits are required to support telephone operations. These include the following:

TX Audio = 2wires RX Audio = 2 Wires Hook Switch = 1 Wire (Referenced to Ground) Incoming Ring Signal = 1 Wire (Referenced to Ground) Ground Wire = 1 Wire

Base Unit (J2)

Signal

CTU/Transceiver

Connection

1 Shield Chassis Ground/Airframe 2 RX Hi 4-W Receive Hi 3 RX Lo 4-W Receive Lo 4 TX Hi 4-W Transmit Hi 5 TX Lo 4-W Transmit Lo 6 Ring In Ring Out 7 Hook Switch Hook Signal 8 Ring/Hook Switch Common CTU/Transceiver Ground 9 Power 28 VDC 4 wire only + 28 VDC

10–15 No Connection N/C

Note

It is important to remember that the ring-In signal and

Hook-switch signals must be referenced to the same

return as the CTU or Transceiver return signals. This is

usually power supply return or chassis ground.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Recommended Cable Eight conductor (4-twisted pairs) stranded Overall shield 20–24 AWG

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

5. Cradle Connections

The cradle is provided with a pre-wired cable and connector for connection to the base unit. The standard cable length is 35.4 inches (90 cm). However, ICG provides a connector kit to permit manufacture of an extension cable or the cradle unit can be ordered with a longer pre-wired cable attached.

The cradle has a pre-wired 35-in. (90-cm) cable with connector for connection to the base unit. Connector pinning and signal descriptions are shown in the Wiring section.

When the cradle is mounted, it is fastened through “4-40 PEM” nuts in the rear of the cradle. Typically, the cradle unit is mounted onto a plate or bulkhead panel that is re-installed after mounting.

CAUTION

THE PEM NUTS ON THE CRADLE PROVIDE A

MAXIMUM DEPTH OF 0.472 in. (12 mm) FOR

MOUNTING SCREWS OR BOLTS. IT IS RECOMMENDED THAT THE MAXIMUM

PENETRATION OF THE MOUNTING HARDWARE IS

NO MORE THAN 0.394 in. (10 mm).

(A)

Handset

The cordless handset

is a standard RTX handset with a modification to provide the automatic shut-off feature. Before the handset is operated it should be charged for approximately 2 hours to provide a maximum ch

Cordless with Magnetic Stripe Reader

(B)

arge on the batteries.

The 1.9-GHz Cordless telephone is available with an optional magnetic-stripe reader attached. In this configuration, the cradle and magnetic (mag)-reader are mounted on a special mounting plate. Wiring between the cradle and mag-reader is internal. Additionally, two extra wires are utilized in the cradle-to-base-unit cable to provide the tip-and-ring Telco signals to the mag-stripe reader. Consideration should be made to extend these signals if an extender cable is manufactured to lengthen the cradle-to-base-unit cable.

When mounting the cordless with mag-reader, consult the dimensional drawing for the mag-reader mounting plate in the section, “Fits and Clearances.”

Note

The mounting-hole locations on the cradle for the mag

reader are different from that of the cradle assembly

without the mag-reader.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

An extender cable can be manufactured to extend the distance between the location of the charging cradle and the base unit. ICG provides a connector kit (P/N 500480) for the convenience of the installer.

Note

The cable is not included. See the section “Wiring

Diagrams for wiring pin-outs for an extender cable.

The following part numbers are needed for the mating connectors on each end of the extender cable:

Mating Connector Cradle End: (MIL-C-24308/2-1) ITT-Cannon P/N DEMA9S (9 Pin SubD Socket) with D110277 Spring Clips.

Mating Connector Base Unit End: (MIL-C-24308/4-1) ITT-Cannon P/N DEMA9P (9-Pin Sub-D Plug) with D110278 Retaining Clips.

Note

The above part numbers are kits that include connector

body, pins, and back shell. It is not necessary to use the

ITT part; any 9-pin sub-D connectors can be used with

the appropriate spring-and-clip latching mechanism.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Connector Pins 115-VAC 2-Wire Model

J1 Mating Connector: MS24266R10B5SN/Connector Backshell: MS27291-1

Pin 1 110–220 VAC 40–400 Hz Pin 2 220 VAC/115-VAC RTN Pin 3 Chassis GND Pin 4 NC Pin 5 NC

J2 Mating Connector: D-Sub 9 Position Socket (Female)

MIL C 24308/2-1/Backshell: 85049/48-1-1/Spring Latch: Canon D110278

Pin 1 TIP Pin 2 Shield Pin 3 RING Pin 4 NC Pin 5 NC Pin 6 NC Pin 7 NC Pin 8 NC Pin 9 NC

J3 Mating connector: D-Sub 9 Position Plug (Male)

Pin 1: Black Off-Hook LED Pin 2: Red +12 VDC Pin 3 Cradle Ground Pin 4: Yellow Charge (+) Pin 5 TIP (CC Reader) Pin 6: Blue Charge (-) GND. Pin 7 RING (CC Reader) Pin 8: Grey Page/Register Pin 9 Shield

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Connector Pins 28-VDC, 2-Wire Model

J1 Mating Connector: MS24266R10B5SN/Connector Back Shell: MS27291-1

Pin 1 28 VDC (+) Pin 2 28-VDC Return (GND) Pin 3 Chassis GND (Shield) Pin 4 NC Pin 5 NC

J2 Mating Connector: D-Sub 9 Position Socket (Female) MIL C 24308/2-1/Backshell: 85049/48-1-1/Spring Latch: Canon D110278

Pin 1 TIP Pin 2 Shield Pin 3 RING Pin 4 NC Pin 5 NC Pin 6 NC Pin 7 NC Pin 8 NC Pin 9 NC

J3 Mating Connector: D-Sub 9 Position Plug (Male)

Pin 1: Black (Brown) Off Hook LED Pin 2: Red +12 VDC Pin 3: Orange Credit Card Reader Ground / Cradle Ground Pin 4: Yellow Charge Voltage (+)

Pin 5: Green TIP (CC Reader) (No Connection for 463092)

Pin 6: Blue Charge (-) GND. 12-VDC Return

Pin 7: Purple RING (CC Reader) (No Connection for 463092)

Pin 8: Grey Page/Register Pin 9: Shield Shield

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Connector Pinning, 115-VAC 4-Wire Model

J1 Mating Connector: MS24266R10B5SN/Connector Backshell: MS27291-1

Pin 1 110–220 VAC 40–400Hz Pin 2 220 VAC/115-VAC RTN Pin 3 Chassis GND Pin 4 NC Pin 5 NC

J2 Mating Connector: D-Sub 15 Position Socket (female) MIL C 24308/2-2/ Backshell: 85049/48-1-2/Spring Latch: Canon D110278

Pin 1 Shield Pin 2 Rx HI Pin 3 Rx LO Pin 4 Tx HI Pin 5 Tx LO Pin 6 Ring In (input, active LO) Pin 7 Hook Switch (output, active LO)

System Ground (must be common to CTU/Transceiver

Pin 8

ground)

Pin 9–15 NC

J3 Mating connector: D-Sub 9 position Plug (Male)

Pin 1: Black Off Hook LED

Pin 2: Red +12 VDC

Pin 3 Cradle Ground

Pin 4: Yellow Charge (+)

Pin 5 Future Use

Pin 6: Blue Charge (-) GND.

Pin 7 Future Use

Pin 8: Grey Page/Register

Pin 9 Shield

J1 J3

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Connector Pins, 28-VDC, 4-Wire Model

J2 Mating Connector: D-Sub 15 position Socket MIL C 24308/2-2/Backshell: 85049/48-1-2/Spring Latch: Canon D110278

Pin 1 Shield Pin 2 Rx HI Pin 3 Rx LO Pin 4 Tx HI Pin 5 Tx LO Pin 6 Ring In (input, active LO) Pin 7 Hook Switch (output, active LO) Pin 8 System Ground (must be common to CTU/Transceiver ground) Pin 9 +28 VDC

J3 Mating connector: D-Sub 9 position Plug (Male)

Pin 1: Black (Brown) Off-Hook LED

Pin 2: Red +12-VDC

Pin 3: Orange Cradle Ground

Pin 4: Yellow Charge Voltage(+) Pin 5: Green Future Use

Pin 6: Blue Charge (-) GND. 12-VDC Return

Pin 7: Purple Future Use

Pin 8: Grey Page/Register

Pin 9: Shield Shield

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

Notes

1. All nine conductors are required.

2. The cable from the cradle to the base unit is a Teflon-insulated, shielded 9*AWG24 (19). (Isotec-P/N: 1TXS24-19 (10) SFJ), ICG P/N 211031.

POWER CONSUMPTION: Not to Exceed 20 VA at 28 VDC

WEIGHT: Base Unit: 770 grams. Cradle with Handset: 800 grams.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

AIR WORTHINESS/RMA PROCEDURE

1. Air Worthiness

The Cordless handset is not flight critical. This equipment complies with Parts 68 of the FCC rules and the requirements adopted by the Administrative Council for Terminal Attachments (ACTA). This device complies with Part 15 of the FCC rules. For further information on Parts 15 and 68, see “FCC and other information” on the Safety Information sheet.

The removal of the unit is based only on the condition of failure or upgrade. There are no required maintenance and troubleshooting procedures other than those detailed in this manual. If the Cordless handset requires removal because of a failure condition, return the defective unit to ICG as instructed below.

2. ICG Customer Support for Returning Cordless Units

Contact Customer Support to arrange for a Return Material Authorization (RMA) number. ICG Customer Support will request the following information before issuing an RMA number:

• Product Model Number

• Product Part Number

• Product Serial Number

• Installation location (aircraft Tail Number or other identifier)

• Problem description

• Technical contact name with contact Information

• Return address for repaired/refurbished unit

• Original installation date and installing agent, if known.

3. ICG Customer Service Contact Information

TELEPHONE:

Within the U.S. 1-800-279-1991 Select Customer Support option when prompted by

Outside the U.S. 1-757-947-1030 Select Customer Support option when prompted by

Direct Line 1-757-947-1060

FAX: E-Mail:

the Automated Attendant.

1-757-947-1036

techsupport@icg.aero

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

4. Packaging For Shipment

If the original packaging is available, please return the defective device in its original container and packaging materials. When this is not possible, internal packaging material should be of a type that guards against static accumulation.

DISCLAIMER: ICG is not responsible for damage during shipping or for freight charges for returned

equipment.

5. Package Markings

Aside from the customary shipping information, the outside of the shipping container should display the RMA number. The packing list must also include the RMA number and any special instructions, purchase order information, etc.

6. Shipping

The customer is responsible for selecting the courier or freight transport service and is responsible for all freight charges, customs clearance fees, taxes, duties, insurance, etc.

7. Notification

Notify ICG customer service as soon as the device is shipped and provide the following information: freight forwarder, airway bill, anticipated arrival at ICG, etc.

8. Website for Notices, Patches, and Updates to the Firmware

ICG has established on the corporate website (www.icg.aero) an area where clients can register to

receive advance information and notices about changes to this unit. Clients wishing to participate will also be able to download patches or future updates as those become available.

To take advantage of this free opportunity, simply go to the ICG website and fill out the requested information. You may remove your name from this service at any time.

Privacy Statement

ICG will not sell, trade, or transfer user addresses or

information to any other sources.

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

GLOSSARY

For your convenience, you will find here an acronym and abbreviation list pertinent to the material in this document. If the terminology is specialized, the terms will generally be written out to save you the inconvenience of having to look up the meaning of an acronym. However, common terms and units of measure will appear in the text as their recognized acronyms.

AC Alternating Current AIU Analog Interface Unit

AW Air Worthiness AWG American Wire Gauge CTU Cabin Telephony Unit

DC Direct Current DECT Digital Enhanced Cordless Telecommunications

DTMF Dual-Tone Multi-Frequency

FAA Federal Aviation Agency

FCC Federal Communications Commission ICG International Communications Group, Inc. LCD Liquid Crystal Display

LEP List of Effective Pages mA Milliamperes N/A Not Applicable PC Personal Computer

PCB Printed Circuit Board

PCM Pulse Code Modulation

P/N Part Number PIN Personal Identification Number

RMA Return Material Authorization

RR Record of Revisions SB Service Bulletin TOC Table of Contents TR Temporary Revision

W Watts

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

THIS PAGE IS INTENTIONALLY LEFT BLANK.

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Cabin Handset

INTERNATIONAL COUNTRY CODE DIRECTORY

International country codes are listed here. The countries are listed in alphabetical order.

Country

Afghanistan +93 Albania +355

Algeria +213 American Samoa +1 (684)

Andorra +376 Angola +244

Anguilla +1 (264)

Argentina +54 Armenia +374

Aruba +297 Ascension +247

Australia +61

Austria +43 Azerbaijan +994

Bahamas +1 (242) Bahrain +973

Bangladesh +880 Barbados +1 (246)

Belarus +375 Belgium +32

Belize +501 Benin +229

Bermuda +1 (441) Bhutan +975

Bolivia +591

Botswana +267 Brazil +55

British Virgin Islands

Bulgaria +359 Burkina Faso +226

Burma (Myanmar)

Cambodia +855 Cameroon +237

Canada +1 Cape Verde +238

Caribbean Nations

Central African Republic

Chile +56 China +86

Colombia +57

Country Code

+1 (284) Brunei Darussalm +673

+95 Burundi +257

+1 Cayman Islands +1 (345)

+236 Chad +235

Country

Antigua and Barbuda

Australian External Territories

Bosnia and Hercegovina

Comoros & Mayotte

Country Code

+1 (268)

+672

+387

+269

Congo (Brazzaville)

Country

Cote d'Ivoire (Ivory Coast)

Cuba +53 Cyprus +357

Czech Republic +420 Denmark +45

Diego-Garcia +246 Djibouti +253

Dominica +1 (767) Dominican Republic

East Timor +670 Ecuador +593

Egypt +20 El Salvador +503

Equatorial Guinea

Estonia +372 Ethiopia +251

Europe --- Falkland Islands +500

Faroe Islands +298 Fiji +679

Finland +358 France +33

French Antilles +590 French Guiana +594

French Polynesia

Gambia +220 Georgia +995

Germany +49 Ghana +233

Gibraltar +350 Greece +30

Greenland +299 Grenada, Carricou +1 (473)

Guadeloupe (see

French

Antilles)

Guatemala +502 Guinea +224

Guinea-Bissau +245 Guyana +592

Haiti +509 Honduras +504

Hong Kong +852 Hungary +36

+242

Country Code

+225 Croatia +385

+240 Eritrea +291

+689 Gabon +241

+590 Guam +1 (671)

Congo (Kinshasa, formerly Zaire)

Country

+243

Country Code

+1 (809), +1 (829)

Cordless Handset

May 2007

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Telephone Handset

Iceland +354 India +91

Indonesia +62 Inmarsat

International Freephone Service

Iraq +964 Ireland +353

Israel +972 Italy +39

Ivory Coast (Cote d'Ivoire)

Japan +81 Jordan +962

Kazakstan +7 Kenya +254

Kiribati, Gilbert Islands

Kyrgyz Republic +996 Laos +856

Latvia +371 Lebanon +961

Lesotho +266 Liberia +231

Libya +218 Liechtenstein +423

Lithuania +370 Luxembourg +352

Macao +853 Macedonia +389

Madagascar +261 Malawi +265

Malaysia +60 Maldives +960

Mali +223 Malta +356

Marshall Islands +692 Martinique +596

Mauritania +222 Mauritius +230

Mexico +52 Micronesia +691

Moldova +373 Monaco +377

Mongolia +976 Montserrat +1 (664)

Morocco +212 Mozambique +258

Namibia +264 Nauru +674

Nepal +977 Netherlands +31

Netherlands Antilles

New Zealand +64 Nicaragua +505

Niger +227 Nigeria +234

Niue Island +683

North Korea +850

Norway +47 Oman +968

+800 Iran +98

+225 Jamaica +1 (876)

+686 Kuwait +965

+599 New Caledonia +687

North American Numbering Plan

Northern Mariana Islands (Commonwealth of)

+870 to +874

+1 (670)

Pakistan +92 Palau +680

Palestine +970 Panama +507

Papua New Guinea

Peru +51 Philippines +63

Poland +48 Portugal +351

Puerto Rico +1 (787) Qatar +974

Reunion (France)

Russia +7 Rwanda +250

St Helena +290 St Kitts and Nevis +1 (869)

St Lucia +1 (758)

St Vincent/Grenadi nes

San Marino +378

Saudi Arabia +966 Senegal +221

Serbia and Montenegro

Sierra Leone +232 Singapore +65

Slovakia +421 Slovenia +386

Solomon Islands +677 Somalia +252

South Africa +27 South Korea +82

Spain +34 Sri Lanka +94

Sudan +249 Suriname +597

Swaziland +268 Sweden +46

Switzerland +41 Syria +963

Taiwan +886 Tajikistan +992

Tanzania +255 Thailand +66

Togolese Republic

Tonga +676

Tunisia +216 Turkey +90

Turkmenistan +993 Turks and Caicos +1 (649)

Tuvalu, Ellice Islands

Ukraine +380

United Kingdom +44 United States +1

+675 Paraguay +595

+262 Romania +40

St Pierre and Miquelon

+1 (784) Samoa +685

Sao Tome & Principe

+381 Seychelles +248

+228 Tokelau +690

Trinidad and Tobago

+688 Uganda +256

United Arab Emirates

+508

+239

+1 (868)

+971

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group, Inc.

User’s Guide and Installation Manual

1.9-GHz Cordless Unit

Aviation Telephone Handset

U.S. Pacific Islands

U.S. Virgin Islands

Uzbekistan +998 Vanuatu +678

Vatican City

Vietnam +84 Wallis & Futuna +681

Yemen +967 Yugoslavia

Zaire - now Congo (Kinshasa)

Zanzibar (see Tanzania)

+1 670, +1 671, +1 684

+1 (340) Uruguay +598

+39, +379

+243 Zambia +260

(+259 never used)

Universal Personal Telecommunications+878

Venezuela +58

(+38 discontinue d)

Zimbabwe +263

Cordless Handset

Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.

May 2007

International Communications Group 463091, 463093, 463095, 463092 User Manual And Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

DISPLAY

UP&DOWN