International Comfort Products CPFILTRK007A00, CPFILTRK008A00, CPFILTRK009A00 Installation Manual

COMMERCIAL PACKAGED PRODUCT (2 - 5 TONS)

Part Number:

CPFILTRK007A00, CPFILTRK008A00 & CPFILTRK009A00

Installation Instructions

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could cause personal injury or death.

Electrical shock can cause injury or death. Disconnect power supply and install lockout tag before attempting to install accessory.

SAFETY CONSIDERATIONS

Installation and servicing of this equipment can be hazardous due

to mechanical and electrical components. Only trained and qualied

personnel should install, repair, or service this equipment. Untrained personnel can perform basic maintenance functions such as cleaning and replacing air lters. All other operations must be performed by trained service personnel. When working on this equipment, observe precautions in the literature, on tags, and labels attached to or shipped with the unit and other safety precautions that may apply. Follow all safety codes. Installation must be in compliance with local and national building codes. Wear safety glasses, protective cloth-

ing, and work gloves. Have re extinguisher available.

Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit. Recognize safety information. This is the safety alert symbol . When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand these signal words: DANGER, WARNING, and CAUTION. These words are used with

the safety alert symbol. DANGER identies the most serious hazards

which will result in severe personal injury or death. WARNING signi-

es hazards which could result in personal injury or death. CAUTION

is used to identify unsafe practices which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.

CAUTION

CUT HAZARD

Failure to follow this caution may result in unit damage.

NOTE: On top lter rack for small cabinet, screw left side to coil

frame. On right side, bend tab on rack and screw to unit divider. Hold height dimension shown in Fig. 2.

3. Install the bottom lter rack in the HVAC unit next to the indoor coil. Filter rack will rest on the HVAC base and screw into the left and right

side of the coil frame. Be careful not to insert screws where coil dam-

age could occur. If using 2” (50.8mm) lters remove lter spacer. (See Fig. 2A, 3A and 4A.)

4. Install lters in rack. See Table 1 for sizes.

5. Replace lter access door on HVAC unit.

CPFILTRK007A00

CPFILTRK008A00

CPFILTRK009A00

FILTER RACK PACKAGE

PACKAGE CONTENTS

Part No. Qty Description

1 Top Filter Rack

1 Bottom Filter Rack

2 12 x 20 x 1 Filters

1 Hardware Bag

1 Instructions

1 Top Filter Rack

1 Bottom Filter Rack

1 14 x 24 x 1 Filter

1 16 x 24 x 1 Filter

1 Hardware Bag

1 Instructions

1 Top Filter Rack

1 Bottom Filter Rack

1 16 x 24 x 1 Filter

1 18 x 24 x 1 Filter

1 Hardware Bag

1 Instructions

Sheet metal parts may have sharp edges or burrs. Use care and wear appropriate attire.

General

These lter racks can be used in either a horizontal or vertical

discharge application, and are designed to accommodate either 1” or 2”

(25.4mm or 50.8mm) wide lters. Use caution not to damage indoor

coil during installation.

Installation

1. Remove the lter access panel on the HVAC unit. (See Fig. 1.)

2. Install the top lter rack in the HVAC unit next to the indoor coil.

Lift rack to the very top of the return chamber and screw rack into coil frame on both the left and right side. Be careful not to insert screws

where coil damage could occur. If using 2” (50.8mm) lters remove lter spacer. (See Figs. 2A, 3A, and 4A.)

Filter Accessory Panel for Accessory Filter Rack

Fig. 1 - Panel Removal

Filter spacer remove for 2”

lters

Screw

Fig. 2 - CPFILTRK007A00

Table 1 - Filter Sizes

PART NO. FILTERS

CPFILTRK007A00 (2) 12 X 20* (304.8 X 508mm)

CPFILTRK008A00

CPFILTRK009A00

*If using 2” (50.8mm) eld installed lters use (1) 10x20 (254x508mm) and (1) 12x20 (304.8x508mm). **Install 18 X 24 (457.2mm x 609.6mm) lter rst. The 18 x 24 (457.2mm x 609.6mm) will be on the left side when facing front coil.

(1) 14 X 24 (355.6 X 609.6mm) (1) 16 X 24 (406.4 X 609.6mm)

(1) 16 X 24 (406.4 X 609.6mm) (1) 18 X 24** (457.2 X 609.6mm)

Top Filter Rack

Fig. 2A

Bottom Filter Rack

Filter spacer remove for 2”

lters

Screw

Top Filter

Rack

Fig. 3A

Top Filter Rack

Evaporating Coil

Fig. 3 - CPFILTRK008A00

Top Filter

Rack

Bottom Filter Rack

Evaporating Coil

Screw

Fig. 4A

Filter spacer remove for 2”

lters

Fig. 4 - CPFILTRK009A00

Manufacturer reserves the right to discontinue, or change at any time, specications or designs without notice and without incurring obligations