Intermec Technologies PC24 11 Users manual

Exhibit J: User Manual (DRAFT)

FCC ID: HN2PC24-11

Important PC24-11-FC/R Information!

Contents

P/N XXXXXX-001

For Users in the United States and Canada........................................................................ 2

For Users Outside of the United States and Canada .......................................................... 3

Pour les utilisateurs en dehors du Canada et des Etat-unis ................................................. 4

Für Benutzer außerhalb von Kanada und den Vereinigten Staaten..................................... 6

Per gli utenti al di fuori del Canada o degli Stati Uniti ...................................................... 7

Para Usuarios Fuera de Canada o de los Estados Unidos.................................................... 8

Para Usuários Fora do Canadá ou dos Estados Unidos ...................................................... 9

1

For Users in the United States and Canada

Place this supplement in your manual.
This device complies with Part 15 of the FCC Rules and with RSS-210 of

Industry Canada. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that can cause
undesired operation.

Federal Communications Commission Compliance

This equipment is intended for operation in a commercial environment,
in compliance with the requirements for a Class A digital device, pursuant
to Part 15 of the FCC Rules, and it must not be used in a residential
environment; however, it has also been tested and found to comply with
the more stringent requirements for a Class B device, pursuant to Part 15
of the FCC Rules. It generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instruction
manual, it may cause interference to radio communications. If this
equipment causes interference, the user will be required to correct the
interference at the user’s own expense.

Operation Warning: The user shall stay at least 20 cm (8 in) away from the antenna
of this device, when the device is in use in access points and other hosts, where
higher gain antennas may be used.

Installation Warning: To comply with the FCC’s RF exposure requirements and
minimize health hazards:

Host devices with higher gain antennas such as access points must be installed in
such a way that the user will be at least 20 cm (8 in) away from the antenna, when
the device is in use.

The installers should not forget that the burden of maintaining this distance is on
the installer and not the user. the antennas should be installed in a manner that will
comply with this requirement.

Changes or modifications not expressly approved by Intermec could void the user’s
authority to operate this equipment.

Note: To maintain compliance with FCC Rules, the input/output (I/O) cables that

interconnect between the device and any peripheral must be as specified by Intermec.

Industry Canada Compliance

This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.

2

This device requires a radio license, unless it is used totally inside a
building. (The user must obtain this license.)

Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.

Cet appareil exige une license radio à moins d’être entièrement installé
dans un bâtiment. (L’utilisateur doit obtenir cette license.)

For Users Outside of the United States and Canada

The Intermec product you purchased contains a Model PC24-11-FC/R
transceiver module. This module transmits and receives data using a 2.4
GHz Direct Sequence Spread Spectrum system.

In some host devices the transceiver is user accessible. If you are using such
a device, please pay attention to the radio usage guidelines provided in the
host device manual or getting started guide. The use of the correct antenna
with correct installation is especially important for legal and efficient use
of the product.

In some host devices the transceiver is not user accessible. Please see the
host device manual for any radio-related instructions for those products.

Programming and configuration information for the transceivers is also
provided in the host device documentation. Please check the Intermec
Web site for additional documentation at www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model
PC24-11-FC/R is in compliance with the essential requirements and other
relevant provisions of R&TTE Directive (1999/5/EC). This product has
been assessed to the following standards:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incl. Amdt. 1-4, 11)
The original Declaration of Conformity is available on the Intermec

Technologies Corporation Web site at www.intermec.com.
This product transmits electromagnetic waves at 2.4 GHz frequency

range. It has been tested and found compliant with U.S. (OET Guide 65)
and Canadian (RSS 102) RF exposure regulations. There are no
regulations covering this product type in the European Union at this time.

The transmitter module’s output power is 32mW. The products using this
module are intended for business and industrial environments. They
should not be used in residential environments and by children.

This product is marked with this logo and uses radio frequency bands that are
not harmonized throughout the European Community.

3