Intermec Technologies MPCI3A 20 User Manual

Exhibit J: User Manual-MPCI3A-20

FCC ID: HN2MPCI3A-20

Contents

Part No. 072870-001

Important MPCI3A-20 Information!

For Users in the United States and Canada.......................................................................... 2

For Users Outside of the United States and Canada ............................................................ 3

Pour les utilisateurs en dehors du Canada et des Etat-unis ................................................... 4

Für Benutzer außerhalb von Kanada und den Vereinigten Staaten....................................... 6

Per gli utenti al di fuori del Canada o degli Stati Uniti ........................................................ 7

Para Usuarios Fuera de Canada o de los Estados Unidos...................................................... 8

Para Usuários Fora do Canadá ou dos Estados Unidos ........................................................ 9

1

For Users in the United States and Canada

t

t

Place this supplement in your manual.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that
can cause undesired operation.

Federal Communications Commission Compliance

This equipment is intended for operation in a commercial environment, in compliance with the
requirements for a Class A digital device, pursuant to Part 15 of the FCC Rules, and it must not be
used in a residential environment; however, it has also been tested and found to comply with the
more stringent requirements for a Class B device, pursuant to Part 15 of the FCC Rules. It
generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with
the instruction manual, it may cause interference to radio communications. If this equipment causes
interference, the user will be required to correct the interference at the user’s own expense.

Operation Warning

Warn ing
Avertissemen

Warn ing
Avertissemen

Caution
Conseil

Note

The user shall stay at least 20 cm (8 in) away from the antenna of this device, when
the device is in use in access points and other hosts, where higher gain antennas may
be used.

Installation Warning

To comply with the FCC’s RF exposure requirements and minimize health hazards:

Host devices with higher gain antennas such as access points must be installed in
such a way that the user will be at least 20 cm (8 in) away from the antenna, when
the device is in use.

The installers should not forget that the burden of maintaining this distance is on
the installer and not the user. the antennas should be installed in a manner that
will comply with this requirement.

Changes or modifications not expressly approved by Intermec could void the user’s
authority to operate this equipment.

To maintain compliance with FCC Rules, the input/output (I/O) cables that
interconnect between the device and any peripheral must be as specified by Intermec.

Industry Canada Compliance

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.

This device requires a radio license, unless it is used totally inside a building. (The user must obtain
this license.)

2

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

Cet appareil exige une license radio à moins d’être entièrement installé dans un bâtiment.
(L’utilisateur doit obtenir cette license.)

Agency Approvals

This device is UL Listed and CSA Certified.

For Users Outside of the United States and Canada

The Intermec product you purchased contains a Model MPCI3A-20 transceiver module. This
module transmits and receives data using a 2.4 GHz Direct Sequence Spread Spectrum system.

In some host devices the transceiver is user accessible. If you are using such a device, please pay
attention to the radio usage guidelines provided in the host device manual or getting started guide.
The use of the correct antenna with correct installation is especially important for legal and efficient
use of the product.

In some host devices the transceiver is not user accessible. Please see the host device manual for any
radio-related instructions for those products.

Programming and configuration information for the transceivers is also provided in the host device
documentation. Please check the Intermec Web site for additional documentation at
www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model MPCI3A-20 is in compliance
with the essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC).
This product has been assessed to the following standards:

• ETSI EN 300 328-2 v1.2.1 (2001-12)

• ETSI EN 301 489-17 v1.1.1 (2001-09)

• EN 60950:1992 (incl. Amdt. 1-4, 11)
The original Declaration of Conformity is available on the Intermec Technologies Corporation Web

site at www.intermec.com.
This product transmits electromagnetic waves at 2.4 GHz frequency range. It has been tested and

found compliant with U.S. (OET Guide 65) and Canadian (RSS 102) RF exposure regulations.
There are no regulations covering this product type in the EU at this time.

The transmitter module’s output power is 32mW. The products using this module are intended for
business and industrial environments. They should not be used in residential environments and by
children.

0981

This product is marked with this logo and uses radio frequency bands that are
not harmonized throughout the European Community.

3