Intermec Technologies EASYLAN User Manual

Exhibit O: User Manual 2

FCC ID: HN2EASYLAN

Part No. 072642-001

Important EasyLAN Wireless Information!

Contents

For Users in the United States and Canada ........................................................................2

For Users Outside of the United States and Canada ..............................................................3

Français .................................................................................................................5

Deutsch..................................................................................................................6

Italiano ..................................................................................................................7

Español ..................................................................................................................8

Português ...............................................................................................................9

For Users in the United States and Canada

Place this supplement in your manual.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is

subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that can cause undesired operation.

Federal Communications Commission Compliance

This equipment is intended for operation in a commercial environment, in compliance with the
requirements for a Class A digital device, pursuant to Part 15 of the FCC Rules, and it must not be used
in a residential environment; however, it has also been tested and found to comply with the more
stringent requirements for a Class B device, pursuant to Part 15 of the FCC Rules. It generates, uses, and
can radiate radio frequency energy. If not installed and used in accordance with the instruction manual, it
may cause interference to radio communications. If this equipment causes interference, the user will be
required to correct the interference at the user’s own expense.

To maintain compliance with FCC Rules, the input/output (I/O) cables that

Note:

interconnect between the device and any peripheral must be as specified by Intermec.

Operation Warning

To comply with the FCC’s RF exposure requirements and minimize health hazards:
The user shall stay at least 20 cm (8 in) away from the antenna of this device, when
the device is in use in Intermec printers.

Installation Warning

To comply with the FCC’s RF exposure requirements and minimize health hazards:

Printers containing this device must be installed in such a way that the user will be
at least 20 cm (8 in) away from the antenna, when the device is in use.

The installers should not forget that the burden of maintaining this distance is on
the installer and not the user. the antennas should be installed in a manner that will
comply with this requirement.

Caution

Changes or modifications not expressly approved by Intermec could void the user’s
authority to operate this equipment.

Industry Canada Compliance

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.

This device requires a radio license, unless it is used totally inside a building. (The user must obtain this
license.)

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

2

Cet appareil exige une license radio à moins d’être entièrement installé dans un bâtiment. (L’utilisateur
doit obtenir cette license.)

For Users Outside of the United States and Canada

The Intermec product you purchased contains a Model 2126 transceiver module. This module transmits
and receives data using a 2.4 GHz Direct Sequence Spread Spectrum system.

In some host devices the transceiver is user accessible. If you are using such a device, please pay
attention to the radio usage guidelines provided in the host device manual or getting started guide. The
use of the correct antenna with correct installation is especially important for legal and efficient use of
the product.

In some host devices the transceiver is not user accessible. Please see the host device manual for any
radio-related instructions for those products.

Programming and configuration information for the transceivers is also provided in the host device
documentation. Please check the Intermec Web site for additional documentation at www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model 2126 is in compliance with the
essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product has
been assessed to the following standards:

ETSI EN 300 328-2 v1.2.1 (2001-12)

•

ETSI EN 301 489-17 v1.1.1 (2001-09)

•

EN 60950:1992 (incl. Amdt. 1-4, 11)

•

SP/DGPT/ATAS 23 (1995-02)

•

The original Declaration of Conformity is available on the Intermec Technologies Corporation Web site
at www.intermec.com.

This product transmits electromagnetic waves at 2.4 GHz frequency range. It has been tested and found
compliant with U.S. (OET Guide 65) and Canadian (RSS 102) RF exposure regulations. There are no
regulations covering this product type in the EU at this time.

The transmitter module’s output power is 100mW or less. The products using this module are intended
for business and industrial environments. They should not be used in residential environments and by
children.

This product is marked with this logo and uses radio frequency bands that are not
harmonized throughout the European Community.

The following table indicates the areas of intended use of the equipment and any
known restrictions.

3