Intermec Technologies 02CN3, 06CN3, 01CN3, 08CN3, 802UIAG User Manual

Part No. 074821-001

Important BTS080 Information!

Contents

For Users in the United States and Canada....................................................................... 2

For Users Outside of the United States and Canada............................................................. 3

Pour les utilisateurs en dehors du Canada et des Etat-unis.................................................... 5

Für Benutzer außerhalb von Kanada und den Vereinigten Staaten................................................ 6

Per gli utenti al di fuori del Canada o degli Stati Uniti ......................................................... 6

Para Usuarios Fuera de Canada o de los Estados Unidos ...................................................... 7

Para Usuários Fora do Canadá ou dos Estados Unidos ......................................................... 8

For Users in the United States and Canada

Place this supplement in your manual.
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is

subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that can cause undesired operation.

Federal Communications Commission Compliance

FCC Digital Emissions Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the radio or television receiving antenna.

• Increase the separation between the computer equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the radio or television

receiver is connected.

• Consult the dealer or an experienced radio television technician for help.

Operation Warning

To comply with the FCC’s RF exposure requirements and minimize health hazards:
The user shall not touch the antenna of this device when the device is in use.

Caution

Changes or modifications not expressly approved by Intermec could void the user’s
authority to operate this equipment.

Industry Canada Compliance

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.

This device requires a radio license unless it is used totally inside a building. (The user must obtain this
license.)

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

Cet appareil exige une license radio à moins d’être entièrement installé dans un bâtiment. (L’utilisateur
doit obtenir cette license.)

2

For Users Outside of the United States and Canada

The Intermec product you purchased transmits and receives data using a 2.4 GHz Spread Spectrum
system.

Programming and configuration information for the transceivers is also provided in the host device
documentation. Please check the Intermec Web site for additional documentation at www.intermec.com.

Hereby, Intermec Technologies Corporation declares that this Model BTS080 is in compliance with the
essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC). This product has
been assessed to the following standards:

• ETSI EN 300 328-2 v1.4.1 (2003-04)

• ETSI EN 301 489-17 v1.2.1 (2002-08)

• EN 60950:1992 (incl. Amdt. 1-4, 11)

The original Declaration of Conformity is available on the Intermec Technologies Corporation Web site
at www.intermec.com.

This product transmits electromagnetic waves at 2.4 GHz frequency range. It has been tested and found
compliant with CENELEC EN50360 and EN50361, 1999/519/EC, ACA Radiocommunications Standard
2003, U.S. (OET Guide 65), and Canadian (RSS 102) RF exposure regulations.

The transmitter module’s output power is 11.9 mW. The products using this module are intended for
business and industrial environments. They should not be used in residential environments and by
children.

0981

The following table indicates the areas of intended use of the equipment and any known restrictions.

This product is marked with this logo and uses radio frequency bands that are not
harmonized throughout the European Community.

3