Intermec Z2400 Instructions Manual
P/N 069994-005
Specifications
Design and specifications are subject to change without notice.
Product
Intermec Z2400 battery charger
(P/N 069991)
Electrical requirements
Input voltage: x 12V 1,7A
Application
Intermec lithium-ion battery packs
(P/N 063278, 068537, 068868, 073152, or 073153)
Maximum voltage
Battery P/N 063278, 068868, or 073153: 8,2V
+/- 125mV
Battery P/N 068537 or 073152: 8,4V +/- 125mV
Operating environment
Temperature: 0ºC to 40ºC (32ºF to 104ºF)
Humidity: 0 to 95%, no n-condensing
Storage environment
Temperature: -20ºC to 50ºC (-4ºF to 122ºF)
Humidity: 0 to 95%, no n-condensing
Dimensions
Approx. 51 x 102 x 178 mm (2 x 4 x 7 in)
Weight
Approx. 394.1g (13.79 oz) (without power supply)
Ordering Power Cords for the Battery Charger
The AC power cord is ordered separately. If you need to order an Intermec
power cord, contact your Intermec sales representative.
Country Part Number
North and Central America 586105
Europe 586267
Denmark and Greenland 586283
Italy and Chile 586282
Liechtenstein and Switzerland 586276
United Kingdom 586266
South Pacific 586281
China 071918
Z2400 4-Pack Battery Charger Instructions
*069994-005*
*069994-005*
6001 36th Avenue West
Everett, WA 98203
U.S.A.
www.intermec.com
© 2003 Intermec Technologies Corp.
All Rights Reserved
Z2400 4-Pack Battery Charger Instructions
Use the Trakker Antares® Z2400 battery charger (P/N 069991) to simultaneously
charge up to four battery packs for the Trakker Antares 242X and 243X handheld terminals or the 502X Data Collection PC.
This guide describes how to install and use the charger. Before using the charger,
please read this guide thoroughly and r etain it for future reference. For hel p
managing battery power, see your Trakker Antares 242X terminal, Trakker
Antares 243X terminal, or 502X Data Collection PC user’s manual.
Choosing a Location for the Battery Charger
Warning
To prevent fire or electric shock, do not expose the battery
charger to rain or moisture.
Avertissement
Pour éviter des risques d’incendie ou de choc électrique, ne
pas exposer le chargeur de la batterie à la pluie ou à
l’humidité.
Choose an appropriate location for the charger using these guidelines:
• Locate a flat, stable, and clean surface that is within 1.5 m (5 ft) of an
electrical source (AC outlet).
• Provide access to the power supply jack on the battery charger and to the
battery charger itself so you can easily load and unload batteries.
Connecting the AC Power Supply
Before you can use the battery charger, you need to connect an autoranging AC
power supply (P/N 065236). Plug the AC power supply connector into the power
supply jack on the battery charger, and then connect the AC power cord to the
power supply and to an AC outlet. Both the power supply and the AC power
cord are ordered separately. For help determining which AC power cord to
order, see “Ordering Power Cords for the Battery Charger” later in this guide.
Charging a Battery Pack
You can charge up to four Intermec-labeled lithium-ion battery packs
(P/N 063278, 068537, 068868, 073152, or 073153 in any combination)
simultaneously, using any slot. The charging time depends on the condition
of the battery. Usually, a battery is fully charged in 4 to 6 hours.
Loading and Unloading a Battery Pack Into the Charger
Align the battery pack with a battery slot on the charger (as shown in the
illustration) and slide the battery pack down until it fits firmly in the charger.
To unload a battery pack from the charger, simply pull it out of the battery slot.
You can unload and use a battery pack before it has been fully charged.
Z2400
battery
charger
AC power
supply
2400I001.eps
Status
LEDs
AC power
cord
AC power
supply connector
AC power
supply jack
Lithium-ion
battery
pack
Battery label
on reverse
side of battery
Charger lens
(4 places)
Interpreting the Status LEDs
Each battery slot has two status LEDs that indicate the status of the battery pack
in the slot.
Yellow The battery pack is charging.
Green The battery pack is fully charged or overheated.
Off The battery slot is empty, the charger is not plugged in, or the battery is defective.
Flashing Yellow There has been a charge interrupt, a timeout, or the battery is cold.
Important Recommendations
• Use only Intermec-labeled lithium-ion battery packs (P/N 063278, 068537,
068868, 073152, or 073153) in the battery charger.
• Charge the battery pack immediately before use or within a couple of days of
use.
• For maximum battery efficiency, charge the battery at the recommended
charging temperature of 25ºC (77ºF).
• While the charger is in use, it becomes warm. This is normal.
• Keep the battery and charger contacts clean and free of dust and dirt.
Remove any accumulated debris using a non-metallic pointed object.
• Clean the contacts on the charger and battery pack with a cotton swab and
isopropyl alcohol.
• Clean the battery slot charger lens with a cotton swab and isopropyl alcohol.
• Clean the battery pack label with a cotton swab and isopropyl alcohol.
• Do not let anything metallic come into contact with the battery charger
contacts.
• Do not disassemble the charger. There are no user-serviceable parts in the
charger.
• Do not place the charger in locations that are extremely hot or cold, dusty or
dirty, very humid, or subject to vibration.
• If any part of the charger appears worn or damaged or if any difficulty arises
while using the battery charger, unplug the battery charger immediately and
contact your Intermec service representative.
Troubleshooting
If the charger does not charge the battery pack or if the LEDs do not light, try the
following solutions:
• Make sure that the AC po wer supply is connected to t he charger, plugged i n
to an electrical outlet, and that the electrical outlet has power.
• Make sure that the battery charger contacts are clean.
• Make sure that the battery slot charger lens and battery pack labels are clean.
Loading...