Intermec AD1 Quick Setup Manual

Download

Page 1

Worldwide Headquarters

6001 36th Avenue West

Everett, Washington 98203

U.S.A.

tel 425.348.2600

fax 425.355.9551

www.intermec.com

AD1 1-Bay Communications Dock

Heading 1

Serial Port Pinouts

Quick Start Guide

Speciﬁcations

What Is the AD1?

AD1 1-Bay Communications Dock Quick Start Guide

*073392-007*

P/N 073392-007

dna 03KC eht rof yrossecca na si )XXX-907-522 N/P( kcoD snoitacinummoC yaB-1 1DA ehT

:ot 1DA eht esu nac uoY .sretupmoC dlehdnaH 13KC

•

.13KC ro 03KC eht rewop

•

.13KC ro 03KC a ni si ti elihw yrettab eht egrahc

•

.snoitacinummoc laires 232-SR gnisu snoitacilppa dna atad refsnart

•

.noitcennoc tenrehtE xTesaB001/TesaB01 a hguorht snoitacilppa dna atad refsnart

•

.noitcennoc B epyT )sub laires lasrevinu( BSU

a hguorht snoitacilppa dna atad refsnart

.1DA eht esu dna llatsni ot woh snialpxe ediug sihT

N uoY tahW dee

:deen uoy ,1DA eht esu oT

•

y.lppus rewop CA na

•

.droc rewop CA na

Ethernet Port PinoutsUSB Port Pinouts

Use this pinout if you want to make your own Ethernet cable.Use this pinout if you want to make your own USB cable. Use this pinout if you want to make your own serial cable.

Electrical Requirements: x 12V, 4A

Requires Intermec AC power supply

~100 to 240V, 50-60 Hz

To prevent ﬁre or electric shock, do not expose the AD1 to rain or

moisture.

You must use the appropriate Intermec power supply with this device or

equipment damage may occur.

IOIOI

12V

2 3

4 5

7 8

DCD

RXD TXD

DTR GND

N/C CTS

RTS DSR

TX+ TXRX+ N/C N/C RXN/C N/C

8765 4321

IOIOI

12V

IOIOI

12V

VBUS

UDC-

UDC+

GND

erom roF .noitacol

ruoy rof

d and power supplyroc rewop etairporppa eht esahcrup ot deen uoY

.evitatneserper selas cemretnI ruoy tcatnoc ,noitamrofni

Page 2

AD1 1-Bay Communications Dock Quick Start Guide

Understanding the Lights

Installing the AD1

If you are using a USB or serial cable, you do not need to set any communications parameters on the CK30 or CK31. Ethernet communications are available on the CK30A model only and on the CK31. If you are using an Ethernet communications cable, you need to conﬁgure the CK30A or CK31 to communicate through the Ethernet por t. You need to set these Ethernet parameters.

If you have a DHCP server:

• DHCP enabled

If you do not have a DHCP server:

• IP address

• Subnet mask

• Default router

If required for your network, you may also need to set these parameters on each CK30A or CK31:

• Primary and secondary DNS servers

• Primary and secondary W INS servers

Ask your network administrator for the parameter values you should set. For help conﬁguring the CK30A, see the CK30 Handheld Computer User’s Manual (P/N 073528). For help conﬁguring the CK31, see the CK31 Handheld Computer User’s Manual (P/N 075207).

To conﬁgure the CK30A

Press the Power (

I) key to turn on the CK30A.

Press the green C key, and then press the orange B key to open the System Main menu.

Select Conﬁguration Utility > Communications > Ethernet > IP Settings and conﬁgure the Ethernet parameters.

Save your changes, and press Esc until you exit the System Main menu.

Press and hold the Power key for 5 seconds to warm boot the CK30A.

To conﬁgure the CK31

Press the Power (I) key to turn on the CK31.

From the Start menu, tap Intermec Settings.

Tap Communications > Ethernet > IP Settings and conﬁgure the Ethernet parameters.

Save your changes, and then exit Intermec Settings.

Press and hold the Power key for 5 seconds to warm boot the CK31.

Where to Find More Information

You may need additional information when working with the AD1 and CK30 or CK31 in a data collection system. Please visit our web site at www.intermec.com to download our current manuals (in PDF).

Patent Information

Product is covered by one or more of the following patents: 5,052,943; 5,195,183;

5,317,691;

5,331,580; 5,544,010; 5,644,471. There may be other U.S. and foreign patents pending.

Conﬁguring Ethernet Communications

Place the AD1 on a ﬂat, stable, and clean surface that is within 1.5 m (5 ft) of an AC power outlet.

Connect the other end of the communications cable to your network.

Place the CK30 or CK31 in the AD1 communications dock.

Connect the AC power supply to the power connector on the back of the AD1, and then connect the power supply to an AC power outlet. The yellow Power light turns on. The AD1 is now ready to charge a battery in a CK30 or CK31. The AD1 fully charges the battery in 3 hours.

(Optional) Connect one or more of the following communications cables:

• RS-232 serial cable

• 10BaseT/100BaseTx Ethernet cable

• USB Type B cable

This table explains the diﬀerent colors of the Charge and Power lights.

Charge light

Power light

IOIOI

12V

Serial connector

Ethernet connector

USB connector

Power connector

2 3

Light Color Description

Charge Oﬀ

Flashing green

Steady green

Flashing red

The AD1 is not receiving power. Make sure the power supply is connected properly.

The battery is charging.

The battery is fully charged.

The battery is not charging. Try these solutions:

• Make sure that the battery is ﬁrmly installed in the CK30 or CK31.

• Make sure that the CK30 or CK31 is ﬁrmly inserted in the bay.

• Make sure the power supply is connected properly to a powered AC outlet.

• Make sure the charging pins on the AD

1 and the battery

contacts on the battery are clean.

Power Oﬀ

Steady yellow

The AD1 is not receiving power. Make sure the power supply is connected properly.

The AD1 is connected to AC power and is ready to use.