Unless otherwise indicated,
all accessories support
both the CN3 and the
CN3e mobile computer.
Accessory NamePart NumberDescription
IP30Multiple configuration
numbers. Consult
the price guide.
A reader that snaps onto the
bottom of CN3 Series devices as
a passive UHF RFID handle.
Docks and Modules
Accessory NamePart NumberDescription
Single Dock871-025-001USB Host and Client Support with bay
for charging an auxiliary battery pack.
(7.5”L x 4.0”W x 2.3”T) Requires Power
Supply 851-082-003 and countryspecific AC power cord. Optional: Single
Dock Ethernet or Modem Modules.
Single Dock Ethernet Module
871-025-101CN3 Series Ethernet Module interfaces with
USB Host connector on Single Dock,
p/n 871-025-001. (1.5”L x 2.5”W x 1”T)
Single Dock Modem Module871-025-102CN3 Series v.92 Modem Module interfaces
with USB Host connector on Single Dock, p/n
871-025-001. (1.5”L x 2.5”W x 1”T) LEDs to
indicate DTR, DCD, TX and RX status.
Multi-Dock871-026-0014-slot Ethernet dock provides extra port
allowing for ability to link up to three (3)
multidocks. (17.2”L x 3.75”W x 2.3” T)
Requires Power Supply 851-075-003 and
country-specific AC power cord.
Multi-Dock, Charge Only871-026-002Allows for charging up to 4 devices.
Requires power supply 851-075-003 and
country specific power cord.
(17.2”L x 3.75”W x 2.3” T)
Multi-dock Wall Mount Kit 203-641-002Allows for mounting of one CN3
Series Ethernet or Charge Only
Multi-Dock to vertical wall surface.
(Used with 700 series too.)
Docks and Modules
CN
Series
Accessories Guide
Accessory NamePart NumberDescription
Vehicle Dock871-027-001 (CN3)
871-027-101 (CN3e)
Vehicle Dock Install Kit 203-802-001Preferred Solution. For connection of
Vehicle Dock Fuse
Block Power Kit
203-803-001Provides connection to vehicle fuse block.
Provides 3.5 mm headphone (output) jack to
allow for integration into the vehicle audio
system. Cabled RS232 or USB Host support
is also available. Requires use of Intermec
RS232 Serial cable (p/n 225-737-001) or
Intermec USB cable VE011-2016.
Handsfree speakerphone capabilities will
be supported via standard, o-the-shelf
Bluetooth headset and handsfree
speakerphone systems.
The CN3 Series vehicle dock uses the same
mounting
vehicle power kits (see below) as the 700 Series
vehicle dock. (5.65”L x 5.31” W x 2.84”T)
Vehicle Dock (871-027-001) directly to
vehicle battery. Includes power cables
and cable mounting hardware. Order
instructions (962-000-021) separately.
Requires Power Cable (226-109-003). Order
instructions (962-040-004) separately.
system (p/n 805-611-001) and
Vehicle Dock Serial Cable225-737-001Adapts CN3 Series Vehicle Dock Comm
Connector to RS232 Serial (DB9M) for
connectivity to serial peripherals.
Cable, Power, Dock
to Fuse Block
Vehicle Dock Mounting Kit805-611-001Allows mounting of Vehicle Dock
Auto Adapter, V-Docks,
3S Circular
Single USB CableVE011-2016Adapts CN3 Series Vehicle Dock
2
226-109-003Used with Vehicle Dock Fuse
Block Power Kit 203-803-001.
(871-027-001) in route vehicle applications.
Consists of one 4¾” adjustable pivot arm
with two 1½” stainless steel balls, and
assembly hardware. Due to wide range
of possible applications, this kit does not
include hardware for securing mount to
vehicle. (Same as used with 700 Series.)
852-057-005Auto Cigarette Lighter Adapter used
to power the CN3 Series Vehicle Dock
(871-027-001). Connects to 3-pin circular
power supply found on back of the v-dock.
Comm Connector to USB-A Female
for connectivity to USB peripherals.
Optional: Use 203-810-001 Cable
Retainer Kit to secure USB connectors.
Holsters & Handles
Belt holster designed for use with handheld
applications requiring scan handle support.
Customer installable. Use of scan
handle requires CN3 handheld unit
with an “H” in position #6 of the
configuration part number. All CN3E
configurations support the scan handle.
Holster for use with CN3 and CN3E
when using scan handle.
Lightweight holster designed for use with
handheld applications where scan handle
is not required. Includes integrated belt clip
that allows for easy attachment to belt.
Snap-on Adapters
Accessory NamePart NumberDescription
Mag Strip Reader850-557-001Attaches to heel of CN3 Series devices
and provides magnetic stripe reader.
Optional: Power Supply (851-089-003)
and country-specific AC power cord.
3
RS232 Snap-on,
RoHS Adapter
USB Pass-through
Snap-on Adapter
Ethernet Snap-on,
RoHS Adapter
Power/Audio Snap-on,
RoHS Adapter
850-558-001
850-559-001Snap-on adapter for enabling USB host
850-560-001Supports RJ45 connection. Must purchase
850-561-001Snap-on power adapter recommended for
Snap-on adapter for enabling RS232 or
DEX cabled support from bottom of CN3 or
CN3e. Must order cables separately. Adapter
provides DB9M connector. Must order DEX
cable p/n# 236-194-001 separately. Supports
use of auto power charger p/n# 852-066-001
or AC power supply 851-089-003.
or client communications from bottom
of CN3 or CN3e. Must order cables
separately. Adapter provides DB15M
connector. Requires use of USB adapter
cable p/n VE011-2016. Supports use of
auto power charger p/n# 852-066-001
or AC power supply 851-089-003.
cable separately. Supports use of auto
power charger p/n# 852-066-001 or
AC power supply 851-089-003.
in-field charging solutions not requiring
vehicle dock. Also provides 3.5mm
standard audio jack for use of headset
with right angle connector. Supports use
of auto power charger p/n# 852-066001 or AC power supply 851-089-003.
Quad Battery Charger852-065-001Charges four CN3 Series battery packs.
Requires Power Supply 851-082-003
and country-specific AC power cord.
Cables
Accessory NamePart NumberDescription
RS232 Cable, DB9 F to DB25 M,
6 feet
226-084-002Connects Vehicle Dock RS232 Adapter
(225-737-001) to External Modem,
6820 Printer, or other serial device.
USB-A to USB-B Cable,
2 meter
USB-A to USB-Mini B Plug
Cable, 2 meter
DB9 to DEX, RoHS Cable236-194-001
Cable, Vehicle Power RoHS236-065-001Split (Y) Power Cable from Trck battery Cable
*NF* Cable, Developers CN3/
CV30
321-576-004Use with CN3 Series Single Dock
(871-025-001) or Vehicle Dock USB Adapter
Cable for ActiveSync (VE011-2016) connection
to PC USB port. Also connects to peripherals
equipped with USB-B Female jack.
321-611-102Use with CN3 Series Single Docks
(871-025-001) or Vehicle Dock USB
Adapter Cable (VE011-2016) for connection
to PB42 printer or other peripherals
equipped with USB-Mini B Female jack.
For use with Snap-on RS232/DEX
Adapter (850-558-001). Includes thumb
screws for secure attachment.
(206-875-xxx) to PB42 (or PB42 Vehicle
Cradle), CK60 or CN3 Series Vehicle Dock
VE011-2018For use with USB Snap-on adapter
(p/n 850-559-001) to support USB
active sync/client requirements.
4
Power Supplies and Adapters
CN
Series
Accessories Guide
Accessory NamePart NumberDescription
Universal Power Supply,
12VDC, 3Skt Output
Universal Power Supply,
12VDC 50W FW5012
Universal Power Supply,
5V FW1805 2.35x0.7
Universal Power Supply
12VDC 8A
CEC/RoHS
851-075-003Use with CN3 Series Multi-docks
(871-026-001 & 871-026-002). Order
country-specific AC power cord separately.
851-082-003Use with CN3 Series Single Dock
(871-025-001) or CN3 Series Quad Battery
Charger (852-065-001). Order countryspecific AC power cord separately.
851-089-003AC power supply with barrel jack. Allows
for charging CN3 Series devices without a
dock, however requires use of CN3 Series
Power Adapter (851-090-001) or CN3 Series
MSR Snap-on Adapter (850-557-001). Order
country-specific AC power cord separately.
851-064-106NORTH AMERICA, AUSTRALIA,
AND NEW ZEALAND USE ONLY.
Use with CN3 Series Multidocks
(871-026-001 & 871-026-002). Order
country-specific AC power cord separately.
Universal Supply
12V 2.5x5.5 FWC5012
CEC/RoHS
Universal Supply
5V FWC1805 2.35x0.7
CEC/RoHS
AC/DC Power Adapter851-090-001Attaches to the bottom of the CN3
Auto Power Adapter, RoHS852-066-001Auto Cigarette Lighter Adapter with
851-082-103NORTH AMERICA USE ONLY.
SEE 851-082-003 FOR USE OUTSIDE
NORTH AMERICA. Use with CN3 Series
Single Dock (871-025-001) or CN3 Series
Quad Battery Charger (852-065-001). Order
country-specific AC power cord separately.
851-089-103NORTH AMERICA USE ONLY.
SEE 851-089-003 FOR USE OUTSIDE
OF NORTH AMERICA. AC power supply
with barrel jack. Allows for charging
CN3 Series without a dock, however
requires use of CN3 Series Power
Adapter (851-090-001) or any of the CN3
Series Snap-on Adapters (See Snap-on
Adapters Section below). Order country
specific AC power cord separately.
Series device’s docking connector to
support barrel jack connections. Allows
for use of Universal AC Power supply
(851-089-003) or the Auto Cigarette
Lighter Power Adapter (852-066-001).
barrel jack that allows for charging
CN3 handheld. Requires use of
AC/DC Power Adapter (851-090-001).