Intermatic WL070HPSPC User Manual

HID Wall Pack - WL Series

INSTALLATION INSTRUCTIONS
Lamp Type: High Pressure Sodium 70 Watt
Models: WL070PSPC

FOR OUTDOOR USE ONLY

NOT FOR USE IN HAZARDOUS ATMOSPHERES

IMPORTANT: Read instruction sheet carefully before installing fixture.

Retain instructions for future reference.

ELECTRICAL REQUIREMENTS

A qualified electrician should complete all required wiring. This fixture is for use with 120V AC only and
must be properly grounded for safety. A mounting suitable for outdoor use and rated for wet locations is
required. Follow all applicable electrical codes and regulations.

WARNING:

Disconnect power at circuit breaker or fuse box before installing or servicing light.

WARNING:

USE MIN 90ºC SUPPLY CONDUCTORS.
CONNECT TO SUPPLY IN EXTERNAL JUNCTION BOX ONLY.
Lamp and housing become very hot during use.
Ensure free air circulation around unit to dissipate heat.
Avoid enclosed locations and locations where flammable debris (leaves, cut grass, etc.) might collect.
Avoid locations where humans or animals might accidentally touch fixture.

WARNING:

Never operate light without fixture lens secured in place. When light is operating, the gas in the lamp is
at high pressure.
Never operate light if the fixture lens is broken or missing.

ARNING:

W

ear safety glasses and gloves when handling lamp, High Pressure Sodium outer envelope is under

W
vacuum and could implode.

MOUNTING & WIRING

Remove fixture lens cover by loosening two screws. (See Figure 2).

1.
Remove reflector by loosening two screws to allow the reflector to slide upward until the keyholes

2.
in the reflector release the screws. (See Figure 3).

3. Select mounting style and knock out the appropriate holes. (See Figure 4).

a. Mounting with two bolts - Knock out two slugs in the rear housing. Mount with (2) bolts

b.

c. Optional bottom conduit entrance - Drill out and tap recessed indentation in the bottom of

d. To weather proof the fixture, be sure to seal all holes in fixture housing (mounting

Electric shock hazard

Fire hazard

Explosion hazard

Explosion hazard

CAUTION:

or lag screws.
Mounting on outlet box - Knock out appropriate holes around outlet hole in rear housing.
Fasten the rear housing to the outlet box using the screws supplied with the outlet box.

rear housing.

conduit, plugs, photo controls, etc.) with silicone sealant.

Mount the fixture vertically with lens on bottom. (See Figure 2).

Fixture lens
cover

crew

S

igure 2

F

Figure 1

Screws

Grounding
Screw

Reflector

Conduit
Entry

Figure 3

round

G
Lead

Photocontrol

Knock-out

Black

White

Figure 4

4. Using provided twist on or other approved connectors, connect the fixture wires to the supply
wires as follows: (See Figure 5)

a. Connect the Black fixture wire to the Black (hot) supply wire.
b. Connect the White fixture wire to the White (neutral) supply wire.
c. Connect the supply grounding wire to the fixture by hooking it around the green

grounding screw between the brass washer and screw head. Tighten the screw
securely.

X1

X3

LAMP

IGN-01

Screw

120 V

COM

X2

COM

Figure 5

Replace reflector; secure it with (2) screws.

5.

6. Screw lamp into socket in lamp holder until finger-tight.

7. Replace fixture lens cover, secure it with (2) screws.

8. To operate, restore power to the circuit and switch light on.

LAMP REPLACEMENT

1.

urn of

T

CAUTION:

f power at circuit breaker or fuse box. Allow fixture and lamp to cool.

Use lamp of correct type and wattage as specified on fixture.

2. Remove fixture lens cover by loosening (2) screws.

3. Remove old lamp and replace with new lamp of correct type and wattage. Screw lamp into socket

in lamp holder until finger-tight.
Replace fixture lens cover

4.

. Secure it with (2) screws, making sure that gasket is properly seated,

free of debris, and compressed to seal out moisture.

5. Turn power back on.

Properly dispose of lamp per manufacturer’s recommendations.

6.

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of
charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in
handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with
instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD

ABOVE. SOME ST

TED

A

ST
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage
prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675­7000 http://www

.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.

THESE INSTRUCTIONS DO NOT

RELATED TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR
DISTRIBUTOR OR INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 [phone] www.intermatic.com

ATES DO NOTALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOTAPPLY TO YOU.

COVER

LIMITED 1 YEAR WARRANTY

ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS

158HL12122