Intermatic PE10000 Series Installation, Operation & Service Manual

Download

Page 1

PE SERIES POOL/SPA EQUIPMENT CONTROLS

INSTALLATION

OPERATION &

SERVICE MANUAL

MMooddeell:: PPEE1100000000 SSeerriiees

CCOONNTTRROOLL PPAANNEELL FFOORR IINNDDOOOORR//OOUUTTDDOOOORR UUSSE

Suitable for Pool Equipment Control and for Direct Connection to a Wet-Niche or No-Niche Luminaire

EELLEECCTTRRIICCAALL RRAATTIINNGGSS:: SSeeee iiIInnssiiddee eenncclloossuurree ddoooor

PP11335533MMEE DDiiggiittaall TTiimmee CClloocckk:: SSeeee rraattiinngg iinnssiiddee eenncclloossuurree ddoooorr ((CClloocckk nnoott iinncclluuddeedd wwiitthh aallll mmooddeellss)

)

The short circuit current rating of this panel board is 10,000 symmetrical amperes.

Many of today’s energy efficient pools and spas utilize the advantages of a single electrical panel, containing all the necessary controls for the safe, efficient and automatic operation of the pool/spa equipment. In addition, this panel can also be used to control any outdoor equipment, sign or pump within its rated capacity.

As an option this all-weather enclosure contains the heavy-duty, industrial grade P1353ME Digital Time Clock. It also has provisions to install switches or a GFCI receptacle on the side as well as the inside.

The P1353ME Digital Time Clock (optional) is designed to operate any pump, within its rated capacity.However, if protection to prevent dry start is required by the pump manufacturer, it must be provided in addition to this control. Contact pump manufacturer if not sure and/or for more details.

DANGER! TO AVOID RISK OF INJURY:

...do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times. ...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA!

Contact a qualified service technician.

...always disconnect electricity before servicing this control or the equipment connected to it.

READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL

GENERAL INFORMATION

Because of our commitment to continuing research and improvements, Intermatic Incorporated reserves the right to make changes, without notice, in the specifications and material contained herein and shall not be responsible for any damages, direct or consequential, caused by reliance on the material presented.

INTERMATIC INCORPORATED, SPRING GROVE, IL 60081-9698

http://www.intermatic.com

158PE13011

LIMITED ONE YEAR WARRANTY

If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace

it, at its sole option, free of charge. This warranty is extended to the original house hold pur

chaser only and is not transferable. this warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair

, opened, taken apart or other

wise modified; (c) units not used in accordance with instructions; (d) damages exceed

ing the cost of the product; (e) sealed lamps and/or lamp bulbs, LED’

s and batteries; (f) the finish on any portion of the product, such as sur

face and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs. INTERMA

TIC INCORPORA

TED WILL NOT BE LIABLE FOR INCIDENT

AL OR CONSEQUENTIAL DAMAGES. SOME ST

ATES DO NOT ALLOW THE EXCLU-

SION OR LIMIT

TION OF INCIDENT

AL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS

ARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED W

ARRANTIES. ALL IMPLIED W

ARRANTIES, INCLUDING THE WARRANTY OF MER-

CHANT

ABILITY AND THE W

ARRANTY OF FITNESS FOR A P

ARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS

LIMITED W

ARRANTY

, AND SHALL BE OF THE SAME DURA

TION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIM-

TIONS ON THE DURA

TION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

This warranty gives you specific legal rights and you may also have other rights which var

y from state to state. W

arranty ser

vice is available by

mailing postage prepaid to: Intermatic Incorporated/After Sales Ser

vice, 7777 Winn Rd., Spring Grove, IL 60081-9698/815-675-7000

http://www/intermatic.com

WIRING DIAGRAM

NOTES: 1. Grounding connections are not shown but must be provided. Refer to the National Electrical Code for details.

2. Diag

rams above are only two of the many variations this Panel can accommodate.

P1353ME Operating instructions

1. Press PR

OG Key to cycle through menu options.

2. Press UP and DOWN arrow keys to change program settings.

ess ENTER k

ey to sa

ve c

hang

es and exit programming mode.

4. Press ON/OFF keys to manually turn devices ON or OFF.

For more details, please refer to instruction manual booklet

OPERATION

NOTE: Refer to P1353ME instruction manual booklet for description of modes.

Page 2

INSTALLATION

ACCESSORIES

TROUBLESHOOTING

1. Remove the two #10 hex head screws from the back

of the enclosure and attach mounting bracket to enclosure.

2. Select the proper location for the control panel and

hang enclosure on a flat vertical surface or other support. When mounting the enclosure, be sure to use hardware capable of supporting its weight. NOTE: The feeds may enter through any one of the 1/2, 3/4, or 1 inch knockouts at the bottom or back of the enclosure. A dimple is positioned on the top of the enclosure for piloting a drill to create an overhead entrance into the panel. The main feed must also pass through a listed outdoor conduit hub, mounted at the time of installation.

3. Prepare the necessary conduit runs, terminate them

at both ends and pull in the conductors as specified by the installation layout. If this control is used for direct conduit connection to a wet-niche or no-niche luminaire, order one of the following:

1/2” non-metallic - order 156PA13713A

3/4” non-metallic - order 156PA13714A 1” non-metallic - order 156PA13715A 1/2” metallic - order 156PA14336

4. Refer to Figure 1 below.

Note that though this figure shows a P1353ME Digital Time Clock installed, the P1353ME is not included on all models. See door panel for the specific configuration and rating of the model you are installing. To wire the panel, follow the wiring diagram located inside the enclosure door. When wiring the P1353ME, make sure that the connections are tight (25 lb

.-in.

minimum) and

insulation clears the pressure plate

(see illustr

ation).

5. If required by the heater manufacturer, the P1353ME

includes a connection for a fire-man switch.This switch only works in conjunction with circuit #1 (Load #1) the P1353ME. Refer to pages 6 & 7 of the instruction manual for connection information, and refer to page 28 for fireman s

witch prog

amming information. Use at least #18 AWG wiring with insulation rated 300 volt or higher. Some heaters may require a special connecting har

ness

, contact heater manufacturer for details. Place heater ON/OFF switch on heater to ON position.

6. To install additional wiring devices inside the enclo-

sure, first remove rectangular knockout(s) in dead front. Next, remove hex head screws in back of enclosure and install stand-offs* in place of scre

Attach wir

ing device to stand-offs.

*Stand-offs are not furnished. Order 21T156A for a set of four (4) stand-offs and mounting hardware.

If external bonding is required, install a bonding lug at bottom of enclosure and bond installation according to code requirements (Order 156T11047A for Bonding Lug Kit).

8. Testing of the installation is optional and recom-

mended only if the desired loads are securely in place and will not be damaged by this test:

a. Turn ON power at breaker panel. b. P1353ME display should fully illuminate and

then start to blink 12:00 a.m. Time clock will not blink only if time has been maintained by internal battery. c. Push each of the ON/OFF buttons to verify devices cycle on and off. In case of unsatisfactory results, turn OFF power, check your wiring, refer to Troubleshooting on Page 3.

9. Install front panel over wiring compartment.

The control is now ready for programming, see OPERATION section on Page 4.

2 3

IMPORTANT SAFETY INSTRUCTIONS

hen installing and operating this Product and other associated equipment, basic safety precautions should always be followed,

including the following:

1. Read and follow all instructions.

2. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.

3. Install this control not less than 5 feet (3 meters in Canada) from inside edge of pool. USE COPPER CONDUCTORS ONLY.

4. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.

5. For Control grounding, bonding, installing and the wiring of underwater lights, refer to Article 680 of the National Electrical Code or Article 68 of the Canadian Electrical Code.

. The Control should not operate any equipment which would cause bodily injury or property damage should it be activated unexpectedly.

READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE INSULATION CLEARS PRESSURE PLATE

Figure 1

SYMPTOM CAUSE(S) CORRECTIVE ACTION

1. Display will not come “ON” 1a. Jumper on back of clock is missing Set Jumper to proper location. See when unit is powered up? or set incorrectly. Pg.7 of instruction manual.

1b. Fuse on back of clock blown open. Replace fuse with 1/8 amps fuse.

See Pg. 7 of instruction manual.

1c. Power to clock not present. Check connections to clock.

Check circuit breakers.

2. F

reeze protection circuit not 2a. Freeze Probe (P/N 178PA28A) Install Intermatic freeze probe. See

working? not installed or bad. Pg. 7 of instruction manual.

2b. Clock programming not setup. Setup freeze programming. See

Pg. 7 of instruction man

ual.

3. Unit does not turn “ON” or 3a. Internal ON/OFF Times have Setup ON/OFF programming. See “OFF” at desired times? not been defined. Pg.’s 24-27 of instruction manual.

3b.

ON or OFF time is in o

verride mode. Cycle through programming menu.

See Pg.’s 24-27 of instruction manual.

3c.

Cloc

k is in Freeze protection Review programming menu. See

Countdown Mode. Pg.’s 29 & 33 of instruction manual.

4. Display continues to blink ON 4a. Power to clock was interrupted long Set time of day on clock.See Pg. 23 and OFF? enough to loose time of day. of instruction manual.

4b. Clock still in programming mode. Press “ENTER KEY” or wait 1

minute for clock to time out.

Fireman switch not working? 5a.Fireman switch wires not hooked up Connect fireman switch wires to

correctly from heater. clock. See Pg. 7 of instruction

manual.

. Fireman switch programming not Program fireman switch settings.

defined. See Pg. 28 of instruction manual.

FLTR

PUMP

HTR

SPA

JETS

CLNR

LITE1

LITE2

HIGH

LOW

AUX 1

AUX 2

AUX 3

W/FA

External Wired Remote Accessory Part Number 133PE1484A (not included with all models)

The New Intermatic Wired Remote Control allows you to control the P1353ME from a remote location. Included with the Wired Remote Control is a label arrangement allowing you to identify each button specific to your pool or spa equipment pad. The new wired remote control comes standard with 100 foot of cable and is designed to slip fit into any standard 1 1/2” conduit adapter.This remote works in conjunction with the P1353ME and displays feedback information on the present state of the pool or spa equipment pad. For more information refer to instructions provided with the accessory.

Freeze Probe Accessory P

art Number 178PA28A

(not included with all models)

he New Intermatic Freeze Probe allows you to protect your pool or spa equipment during an unexpected freeze condition. The freeze probe comes with a 10 foot cable and plugs into the back of the P1353ME. The P1353ME can be programmed to turn on

each or all-individual loads at any desired outside temperature.

Heater Protection (Fireman) Switch is standard with each Digital Time Clock.

It comes standard with a Fireman Switch connection for your pool or spa heater. Simply connect the two wires from your heater thermostat to the back of the P1353ME. The fireman switch is only associated with circuit one on the P1353ME, therefore the filter pump should be connected to circuit one. Program the time desired for the cool down period and the P1353ME will take over. For more details, refer to instruction manual.