Intermatic CA600 Users Manual

Providing a Brighter Solution™

This product is compatible with other Z-Wave enabled products™

TM

WIRELESS CONTROLS

Model CA600

Single-Pole / Multi-Pole

Dimmer600 Watt Switch

Specifications:

Single-Pole (One Location)
or 3-Way (Multi-Location)
or Wireless RF Control
Operating Temperature Range:
32°F (0°C) to 104°F (40°C)
Power Consumption: 2.0W Max

Dimming:

Fade-on& Fade-off
1% Dimming (100 Increments)

Ratings:

120VAC, 50/60Hz
Maximum Wattage: 600W
Minimum Wattage: 40W

Colors:

Includes white, ivory, and light almond
snap-on rocker plates.

Connections:

Black-Line, Blue-Load, Red-Traveler,
Green-Ground

RF Information:

Minimum Range:
50ft indoor; 100ft outdoor
Frequency: 908.42 MHz

Network Information:

Mesh Network - Each line powered
node acts as a repeater to route
distant signals.
Data Rate: 9600 bits/second
Size: 232 Z-Wave™ Nodes

The CA600 In-Wall Dimmer is a Z-wave™ enabled device which is fully compatible with any Z-wave enabled
network. Z-wave enabled devices display the Z-wave logo and guarantee connectivity and interoperability
between devices. Each line powered node in a Z-wave network is designed to act as a repeater forming a
mesh network eliminating radio “dead spots” and providing the highest level of reliability.

Features

- Multiple location dimming when used with wireless accessory controls.

- Multiple location On/Off control using conventional 3-way or 4-way wiring and devices.

- Lights fade up or down turned on or off.

- Automatically returns to last level in the event of power fluctuations.

- Light levels can be set by pressing and holding the rocker until the desired light level is reached.

- Mini-scenes allows local control of connected load plus up to 5 additional Z-wave devices.

- Full 230 device scene control when used with Intermatic InTouch™ server .

- Dimmer always operates local load, does not require central control system.

WARNING: Read instructions completely before installation and retain for future reference.
WARNING:
WARNING:
CAUTION:

attempt to control a receptacle, fluorescent lighting, motor, or transformer.

CAUTION
OTHER CAUTIONS:

1. Use only one (1) dimmer per load. For remote operation, use standard 3-way or 4-way electrical devices for
ON/OFF operation or use with Z-Wave compatible control for wireless control from any location.

2. Use Air-Gap switch to disconnect power when servicing or changing lamp.

3. Use this device only with 75°C rated copper or copper clad wire.

INSTALLATION:

1. WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER AND
TEST THAT POWER IS OFF BEFORE WIRING.

2. For retrofit applications, remove wall plate and disconnect light switch.

3. Refer to wiring diagrams for proper connection of dimmer for intended application.

4. Check that all wire connections are secure.

5. Place all wires inside junction box. Install dimmer using (2) mounting screws furnished. Complete
installation with a decorator style wall-plate.

6. Reconnect your electrical power.

7. Tap top of rocker to turn lights on; tap bottom of rocker to turn lights off; press and hold top of

Operation:

rocker to brighten connected load; press and hold bottom of rocker to dim connected load.

8. For programming instructions refer to the (158CA12789).InTouch Installer & Users Guide

Rocker Color Conversion

The frame and rocker color of this device can be converted to
match interior design requirements. Simply use one of the
included color plates (white, ivory, or light almond) and proceed
as follows (please note that the device must be removed from
the junction box to change the rocker, follow the installation
instructions and warnings).

1. Select the color of the face you desire.

2. The frame has snaps on its sides. Using a small screwdriver
or thumbnail, gently remove the frame and rocker from the
housing body.

3. Take the new frame and position it properly to the housing
body. Notice that the locking snaps will align in only the proper
direction. Line up the plastic snaps with the slots in the housing
body and snap into place.

4. The frame snaps in with an audible click. Ensure that both
snaps are secure. Replace the device in the junction box
following installation instructions.
The color conversion is complete.

FCC STATEMENT OF COMPLIANCE

This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

WARNING! Changes or modifications not expressly approved by Intermatic Inc. could void the user’s authority to operate the
equipment.

On/Off and

(CA5500B)

For installation and/or use in accordance with appropriate electrical codes and regulations.
Consult a qualified electrician for installation and operation.

To avoid overheating and possible damage to this device and connected equipment, do not

(For Incandescent Only): USE WITH INCANDESCENT OR 120V HALOGEN FIXTURES ONLY.

Rocker
Frame
Snap

Note: Air-Gap switch should be used to remove
power from connected loads before servicing.

(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation.

-- Reorient or relocate the receiving antenna or device.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

158CA12471REF

Providing a Brighter Solution™

This product is compatible with other Z-Wave enabled products™

TM

WIRELESS CONTROLS

Wire Connector Installation

Connect wires per Single Pole, 3-Way, or Multi-Way
Application Diagrams as follows:

Screw wire connectors on clockwise making sure no
bare conductors show below the wire connector.
Secure each connector with electrical tape.

3/8”

Strip wires to expose
3/8” of conductors

Insert wires straight
then twist clockwise

Secure each connnector
with electrical tape

Single Pole Application

Hot Black

120VAC

50/60 Hz

Green

Blue

Red

Incandescent
Lighting Load

For non-standard wiring applications, refer to

Wire Combination & Connector Chart

Orange Wire Connector Combination Chart

1- #14 AWG

1- #16 AWG

+

1 #14 AWG

or

1 #16 AWG

or

1-2 #18 AWG

Maximum Load Per Dimmer for Multiple Devices

Cat. No.

CA600

3-Way Application

Hot Black

Green

120VAC

50/60 Hz

1 #16 AWG

1-2 #18 AWG

+

or

Single

600 Watt

1to2#18AWG

Blue

Red

2- #16 AWG

+

Two Devices

500 Watt

Jumper

1- #18 AWG

+

1to3#18AWG

Three or More

400 Watt

Incandescent
Lighting Load

Neutral

Wire Connector

CA600 CA600 CA-3PS / Standard 3-Way Switch

Ground

Neutral

Wire Connector

Ground

Multi-Way Application

Hot Black

Green

120VAC

50/60 Hz

Neutral

Wire Connector

If within ten (10) years from date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace, at its

If within ten (10) years from date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace, at its
sole option. This warranty applies only to the original purchaser and is not transferable. This warranty excludes and this is disclaimed liability for labor for

sole option. This warranty applies only to the original purchaser and is not transferable. This warranty excludes and this is disclaimed liability for labor for
removal of this product or reinstallation. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any

removal of this product or reinstallation. The warranty does not apply to: (a) damage caused by accident, abuse, mishandling, dropping, acts of God, or any
negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with

negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart, or otherwise modified; (c) units not used in accordance with
directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you.

directions; (d) damages exceeding the cost of the product. Some states do not allow a limitation of damages, so the foregoing limitation may not apply to you.
This warranty gives you specific legal rights and you may have other rights that vary from state to state.

This warranty gives you specific legal rights and you may have other rights that vary from state to state.

LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES.

LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES.
ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR

ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS

PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS
THE WARRANTY PERIOD STATED ABOVE.

THE WARRANTY PERIOD STATED ABOVE.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to the

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing postage prepaid to the
nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:

nearest authorized service center listed. Please be sure to wrap the product securely when mailing to avoid shipping damage. This warranty is made by:
Intermatic Incorporated, After Sales Service, 7777 Winn Road, Spring Grove, IL 60081-9698, 815-675-7000 www.intermatic.com

Intermatic Incorporated, After Sales Service, 7777 Winn Road, Spring Grove, IL 60081-9698, 815-675-7000 www.intermatic.com

Blue

Red

CA600 CA-3PS / Standard 3-Way SwitchCA-4PS / Standard 4-Way SwitchCA-3PS / Standard 3-Way Switch CA-4PS / Standard 4-Way Switch

Ground

LIMITED TEN YEAR WARRANTY

LIMITED TEN YEAR WARRANTY

Incandescent
Lighting Load

INTERMATIC INCORPORATED WILL NOT BE

INTERMATIC INCORPORATED WILL NOT BE