Intermatic 158WF12659REF User Manual

WF306

GENERAL INSTRUCTIONS FOR WATERFALL USE

1. Unpack the product, wipe off dust with a damp cloth. Take out all accessories: River rocks, pump, adapter, and waterfall parts

See diagram).

(

2. Familiarize yourself with the pump. Turn valve on pump counter clockwise placing the handle in a horizontal position for maximum water flow. Turn the valve on the pump in a vertical position for minimum water flow.

CAUTION: This pump has been evaluated for use with water only. NOTE: It is recommended the pump be set at its highest flow during assembly and later adjusted to a lower setting if desired. Be sure to unplug pump before adjusting flow setting.

WARNING: RISK OF ELECTRICAL SHOCK

• Do not connect to any voltage other than that shown on the pump.

This pump is supplied with a grounding conductor and grounding-

• type attachment plug. To reduce the risk of electric shock, be certain that it is connected only to a properly grounded, grounding-type receptacle.

• The national electric code requires that a ground fault circuit interrupter (GFCI) be used in the branch circuit supplying waterfall pumps and other pond equipment. See your electrical supplies dealer for this device.

• If the supply cable is damaged it can not be replaced and the pump unit should be discarded.

WARNING: RISK OF FIRE

• Do not use with water above 30˚C.

• Do not pump flammable liquids.

WATERFALL ASSEMBLY

1. Place base of waterfall on a level surface.

2. Take copper top tubing and screw in intermediate copper tubes.

3. Take copper tube assembly and attach to waterfall cover securing with nuts and washers ~ provided.

4. Attach the clear plastic tube to pump and other end of tube to copper tubing protruding below bottom of waterfall cover.

5. Once assembled, place the waterfall cover in base of waterfall.

6. Place pump in the base of waterfall ensuring that the wires go out the notches located on the back of the waterfall base and cover.

7. Locate Panel A slate piece.

8. Using the brackets and screws attach Panel A to the top of the copper tubing.

9. Make sure bevel is toward the front.

10.Attach middle Panel B to the back of top slate piece using screws and nuts, tighten.

11. Attach Panel C to the back of middle slate using the screws and nuts, tighten.

12.Connect the pump and connect the power cord to the AC adapter

DO NOT plug into

outlet at this time. Once assembled, place the waterfall lid in base of waterfall.

WARNING:

Place hook or nail (not included) or choose an attachment mechanism appropriate for your wall in wall and secure fountain by placing hook or nail in chain. Please ensure that product is assembled according to the directions provided in this information packet. Doing these things will increase safety measures and avoid tipping of the waterfall.

6) SCREWS

(

6) PCS

(

N (2) PCS

ANEL A

LATE

PANEL B

ANEL C

RESERVOIR

NOTE: Do not let pump run when NOT submerged in water. Doing so may damage the pump. Always submerge the pump in water first, and then plug in the unit.

14. Fill base with distilled water to approximately 1/2" above pump. Use distilled water only. Tap water will create mineral deposits that will result in the corruption of the W

aterfall and pump.

15. Plug adapter into 120V household outlet. Put stones on the lid. (The waterfall is controlled by the switch on the power cord.) If pump doesn't operate, rotate in-line switch once to turn to "off" and once to turn to "on."

WARNING: This is not a toy. To avoid danger of choking keep small river rocks away from Children and Pets.

NOTE: Ensure that the electrical cord loop is below the electrical outlet.” This will prevent water from running down the cord into the electrical outlet.

MAINTAINING CLEANLINESS AND LIFE OF WATERFALL & PUMP

. Ensure water pump is kept clean and free of debris. We recommend

Motorhead

using distilled water with this product.

NOTE: To clean pump, first make sure pump is UNPLUGGED from 120V circuit and remove front plate. Check for and remove dirt and debris from impeller. Reassemble.

Regulator

Impeller Holder

Front Plate

Seal Ring

Impeller

2. Periodically change water and clean the structure of the waterfall with a mixture of vinegar and cold clean water.

3. Add water to waterfall periodically to keep water level at an optimum

Shaft

Suction Bracket

level (approximately 1/2” above pump) to avoid shortening the life of the pump. Water level should completely cover pump at all times.

NOTE: Never let the pump run dry. This will shorten the life of the pump.

4. To store waterfall after use, unplug the waterfall from the electrical outlet, empty the water, and store in a cool dry place.

TROUBLESHOOTING

1. If jets do not spray correctly, check water level and add if necessary or clean jet holes to unclog any deposits.

2. If pump fails to operate, check the circuit breaker, or try a different outlet to make sure the pump is getting electrical

power.

3. If the pump gurgles, spews, or “burps”, check the water level to make sure the pump has enough water to function.

4. If water is splashing outside of the waterfall, adjust the flow control valve to a lower setting.

LIMITED ONE YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME

TES DO NOT

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.

ALLOW LIMIT

This warranty is extended to the original household purchaser only and is not transferable.

TIONS ON THE DURA

TION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

AUTHORIZED SER

VICE CENTER

This warranty does not apply to:

Intermatic Incorporated

After Sales Service

7777 W

Spring Grove, IL

inn Road

60081-9698

158WF12776