Inter-m VDC-272, VDC-412 Operating Manual
OPERATING MANUAL
1/3" COLOR CCD
CAMERA
VDC-272, VDC-412
MADE IN KOREA
NO: 9007908010
INSTALLATION
• LENS MOUNTING
Take-out the rubber cap before mounting the lens. This camera can use either C or CS
type mount lenses and it fixed C mount from factory. Remove the C mount adaptor by
tuning it counter-clockwise of the camera body when use CS mount lens. Mount the lens
by turning it clockwise onto the lens mount of the camera and connect the lens cable to
the Iris Lens when an auto iris lens is used.
• MOUNTING THE CAMERA STAND
This camera has the mounting foot on the bottom. To move the mounting foot, remove
the two screws holding the foot to the camera body and move the foot to the top and
reattach it with the two screws.
• CONNECTING THE VIDEO CONNECTOR
Plug the BNC jack from the monitor or other device to the BNC connector on the back of
the camera.
• CONNECTING THE POWER
Connect the power source (DC 12V) to the camera.
FOCUS ADJUSTMENT AT ZOOM LENS
This camera selected variable back focus system which is easy adjusted lens focus.
1) Fit in zoom lens and loosen the focus screw with L-wrench count-clockwise.
2) Adjusted lens focus to obtain the sharpest picture on the screen at maximum zoom in
position.
3) Checked sharpest picture on screen at zoom out position.
4) Repeated 2) and 3) process with correct focus with zoom-in and zoom-out position.
After that fixed focus screw with L-wrench.
TROUBLESHOOTING
• If there is no picture on the monitor screen,
–make sure all the cables are properly connected.
–make sure the monitor is properly adjusted.
• If a picture on the monitor screen is not clear,
–clean the lens.
–adjust the lens focus.
• If there is a video noise or other unknown problems,
–stop using the camera and call your local dealer.
Power DC 12V 200mA MAX
Image Sensor 1/3" COLOR CCD
Scanning System 2:1 Interlace
Min. Illumination 0.1 Lux at F:1.4
S/N Ratio 46dB
Video Output Composite 1.0Vp-p NTSC or PAL
Sync. System Internal System
AGC/AWB Automatic
Operating Humidity –90%
Lens Optional
Operating Temperature –20˚C~ 50˚C
Dimension(mm) 55(H)
55(W) 85(D)
Weight 220g
• Handle with care. Do not drop the camera.
• Do not expose the camera to direct sunlight or place it near a heat source.
• Be sure to use the camera in operating temperature range and less than 90% humidity.
• Do not install the camera in an excessively dusty or humid location.
• Do not expose the camera to rain or water.
• Do not install the camera in a location which is subject to excessive vibration or shock.
• Do not install the camera near equipments that generate a strong magnetic field and
radio frequencies.
• Do not disassemble the camera.
• Do not allow anything to get inside the camera.
• When the malfunction is observed, stop using the camera immediately.
Turn the power off and call your local dealer.
CAUTIONS
1. CCD Sensor: 1/3” Interline Transfer Color CCD
2. Camera Mounting Screw Hole
3. Video Output Connector
4. Power Indicator Lamp
5. Power Input Terminal
6. Auto Iris Lens Connector
7. ELC/Iris Switch (Electronic Level Control)
8. BLC On/Off Switch (Back Light Compensation)
PART NAMES/DESCRIPTIONS
SPECIFICATIONS
Common
Model
VDC-272(PAL) VDC-272(NTSC) VDC-412(PAL) VDC-412(NTSC)
Resolution 380 TV Lines 480 TV Lines
Pixel 512(H)
492(V) NTSC 768(H) 494(V) NTSC
512(H)
582(V) PAL 768(H) 582(V) PAL
Individual
* Specifications and design are subject to change without notice for improvement.
Front View Side View Rear View
Bottom View
Loading...