Local Machine
3
2
1
OUTPUT 1
I
NPUT 1
INPUT 2
INPUT 3
INPU IN
L
M LINK
LM LINK
2
1
NLM-8000C
Features
This device is a wall controller that used by connecting with MR-8000 mounted on NPX-8000. It can select the sound source and volume, and can expand
up to eight in the mode of Daisy Chain.
Front Panel
Rear Panel
1. Displaying Window
Sound source, volume, and status information of the
channel set at NPX-8000 are displayed.
2. Selecting Switch
It is a switch that can change the sound source and
volume, and select the status information.
It is selected if the switch is turned to control the
value you want and press the switch at the position
to select.
3. Led Status Displaying Led
It is LED that displays the operation status of the device.
- Channel mode: GREEN LED is on.
- Volume mode: BLUE LED is on.
- Sleep mode: When Led Control is ON, BLUE LED
is on. When Led Control is OFF, LED is off.
In case Led Control is OFF, LED turns off.
- Communication error: RED LED is on.
- Setup mode: MAGENTA LED is on.
- Others: RED LED is on at Mute status.
1. Termination Switch
It is a switch used in the device connected finally in
case of connecting the device using LM port of MR8000 by Daisy Chain mode.
2. Lm Link Port
It is the terminal that can connect power supply
(+40V) and communication, audio line.
<RJ45 Terminal Description>
NO Description
1 CAN – H
2 CAN - L
3 N.C
4 DC 40V
5 GND
6 N.C
7 Audio Out+
8 Audio Out-
※ Be sure to use direct cable when connecting LINK
of device.
※ For cables, it is recommend to use those below
DCR 100m/9.8Ω.
Local Machine
ID1I
D Set
Cancel
Select
ID Set
1
Termin a t i o n
OFF
Firmware
Ver0 .0 .0 .0
Led Control
OFF
ON
LINK ERROR!
Setting
1. ID
2. Ter mi na ti on
3. Firmware
4. Led Control
5. Factory Reset
6. Back
NLM-8000C
Device setup method and cautions
1. Device Basic Operation
- Waiting Screen
1) If you connect NPX-8000 and NLM-8000C, power
is supplied to NLM-8000C, and NLM-8000C is
ON.
2) In case ID of NLM-8000C collides, ID set window
is displayed. In this case, ID is reset.
※ Refer to 2. Device set explanation or MP-8000
manual for ID set.
3) In case NLM-8000C was connected with the device normally, in case it is not communicated,
LINK ERROR is displayed. In this case, check
communication status (cable, etc.) again.
4) When there is no input for 10 seconds on the waiting display, it is converted into sleep mode.
ID Set
-
1) Device ID can be set.
2) In case ID is changed, if the selection switch is
pressed for 5 seconds or longer and the display
window ID phrase is changed into ID SET phrase
and ID can be changed.
3) When selection switch is pressed at the state ID value
to change is displayed after turning the selection
switch, Select, Cancel phrases are displayed. If Select
is selected, ID is changed and is cancelled if Cancel
is selected.
2. Device Set
It is a menu that can set the device.
1) When the selection switch is pressed for 10 seconds or longer on volume mode screen or channel
mode screen, it moves to the setting screen.
2) The menu pops up that can set if the switch is
turned. After turning the selected switch and moving to the menu desired, selection switch is
pressed and the menu is selected.
3) 6. When Back is selected, it returns to Volume
Mode.
- Termination
1) You can check the device termination status.
2) This menu can check ON/OFF status of termination
resistance switch only, and the change can be
done only with the termination switch at the back
of the device.
3) If you press the selection switch, it returns to Setting screen.
- Firmware
1) You can check the firmware version of the device.
- LED Control
Local Machine
Factory Reset?
Volu me
100
Chanel
Mode
OUTPUT 1
INPUT 1
INPUT 2
INPUT 3
Volu me
Mode
Factor y
Reset!!!
Volu me
100
Volu me
100
Mute
OUTPUT 1
INPUT 1
INPUT 2
INPUT 3
OUTPUT 1
INPUT 1
INPUT 2
INPUT 3
M
usic
Mute
Contact In
V
olume
70
Music Mute
NLM-8000C
) When the device is in sleep mode, Led On/Off can
1
be set.
2) When ON is selected, Led is on in case it is
hanged to sleep mode.
c
3) Select OFF if you want to turn OFF Led when it is
in sleep mode.
- Factory Reset
1) The device can be factory initialized.
2) If selection switch is pressed for 5 seconds or
longer under the state Factory Reset? Phrase is
displayed, Factory Reset!!! Phrase is displayed and
the status displaying LED blinks three times.
3) Factory Reset is completed and is re-booted automat-
ically. Reset ID of the device to the usage purpose to
use.
3. Volume Mode, Channel Mode Changing Method
1) If the switch is turned on the Volume control screen,
the Volume of channel selected at present can be
controlled. Please refer to the 4. Channel selecting
explanation for the way of selecting the channel.
2) Turn the selection switch counterclockwise and the
present Volume is reduced, and it can change to 0
at least.
If the selection switch is turned clockwise, the present
3)
Volume is increased, and it can change up to 100
at largest.
4) If the selection switch is pressed, the present
Volume is Muted. When it is Muted, Mute phrase
is displayed at the center of the screen, and when
controlling the Volume, Mute phrase is displayed at
the left bottom.
5) If the selection switch is pressed again, Mute is
cancelled.
※ On the Channel or Setting screen, Mute cannot
be set with the selection switch.
6) In case the point of contact is inputted with MUTE
terminal at the back of NPX-8000, Music Mute
Contact In phrase is displayed, Music Mute phrase
is displayed at the bottom of the screen. The control
of device is possible at this status, but an audio
signal is not outputted at NPX-8000.
1) If selection switch is pressed for 2 seconds or longer
on the Volume Mode screen, Chanel Mode phrase is
displayed, if the selection switch is unhanded under
this status, it is converted into Chanel Mode. In turn,
if the selection switch is pressed for 2 seconds or
longer on Chanel Mode screen, Volume Mode phrase
is displayed, and if the selection switch is unhanded
under this status, it converts into Volume Mode.
4. Volume control
5. CHANNEL SELECTION
1) You can move to the input channel you want mixing
by turning the switch on the Channel selecting
screen.
2) After moving to the channel desired, press the
selection switch and you can select input channel
to be mixed.
3) If the input channel to be mixed is selected, it is
checked V at the Check Box.
4) In case of cancelling the Mixing Channel, if selection
switch is pressed after selecting the channel to cancel,
V of the Check Box disappears, and the pertinent
channel is cancelled.
※ In case an input signal with higher priority than
BGM is broadcasted (EXT Contact, RM 1, RM
2~8, Schedule, Input Contact), Volume control
and Channel selection cannot be done.
Local Machine
115
70 39.7
9
RJ-45
RJ-45
Push
Encoder
STATUS
LED
DC-DC
CAN
DRIVER
MCU
OLED
DISPLAY
1.3 inch
120-240V~50/60Hz,30W
AC INPUT
DC 24V
RS-232C
MONITOR OUT
8 7 6 5 4 3 2 1
+
G
GRXTX
CONTACT OUTPUT
8 7 6 5 4 3 2 1
CONTACT INPUT
POWER
ON
OFF
MUTE EXT
B A
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
AUDIO OUTPUT
+
G
+
G
+
G
+
G
+
G
+
G
+
G
+
G
AUDIO INPUT
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
+
G
+
G
+
G
+
G
+
G
+
G
+
G
+
G
MR-8000
RM LM
ETHERNET
LINK OUT
LINK IN
LM LINK
LM LINK
LM LINK
LM LINK
LM LINK
LM LINK
LM LINK
LM LINK
NLM-8000C (MAX 8EA)
NLM-8000A
Daisy chain is a wiring scheme in which
multiple devices are wired together in sequence.
NLM-8000C
Application
Specifications
NLM-8000C
Communication mode CAN (Controller Area Network)
ommunication speed 20kbps
C
Communication distance MAX 300m(Including LINK connection)
ower Source DC 40V
P
Power consumption 2.4W
Weight(Set) 133g/0.29lb
Dimensions(Set)
* Design and specification are subject to be changed for the improvement of
roduct quality without pre notice.
p
70(W) x 115(H) x 39.7(D)mm
2.75(W) x 4.52(H) x 1.56(D)in
Block Diagram
※ DIMENSIONS
No. 140523 2017.5
Loading...