Operation Manual
High Resolution IR D/N Dome Camera
IDI-540P(N)
WARNINGS AND CAUTIONS:
CAUTION:
CAUTIONCAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
Should any liquid or solid object fall into the cabinet,
unplug the unit and have it checked by the qualified
personnel before operating it any further.
Unplug the unit from the wall oulet if it is not going to
be used for several days or more. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
Allow adequate air circulation to prevent internal heat
build-up. Do not place the unit on surfaces (rugs,
blankets, etc.) or near materials(curtains, draperies)
that may block the ventilation holes.
Height and vertical linearity controls located at the
rear panel are for special adjustments by qualified
personnel only.
Do not install the unit in an extremely hot or
humid place or in a place subject to excessive
dust, mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage the unit.
Clean the unit with a slightly damp soft cloth.
Use a mild household detergent. Never use
strong solvents such as thinner or benzine as
they might damage the finish of the unit.
Retain the original carton and packing
materials for safe transport of this unit in the
future.
Safety ----------------------------------------- Installation -----------------------------------
Cleaning --------------------------------------
PRECAUTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
ii
FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED
AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION
AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS
OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT
GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH
THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE
TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN
A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO
CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE
COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN
ICES-003.
NORME NMB-003 DU CANADA.
WARNING
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.
CE COMPLIANCE STATEMENT
FCC COMPLIANCE STATEMENT
iii
IMPORTANT SAFEGUARDS
1 -1 Class 2 power source only.
7
-2 Do NOT use power source other than that specified.
17
17. CAUTION-these servicing instructions are
for use by qualified service personnel only.
to reduce the risk of electric shock do not
perform any servicing other than that contained
in the operating instructions unless you are
qualified to do so.
5. ACCESSORIES
iv
1
The camera provides high-quality images using SONY CCD technology especially
designed for closed-circuit television (CCTV) and security surveillance
applications.
Features:
High resolution and high performance 1/3" SONY Super HAD CCD
Technology
Excellent picture quality
540 lines(Color) of resolution
0.5 lux(Color), 0 lux(IR LED ON) @ F.1.2 Sensitivity
Auto electronic shutter [1/60(1/50) ~ 1/120,000] and manual electronic
shutter modes
OSD (On Screen Display)
(Digital Noise Reduction) Auto Function
DNR
Auto and manual white balance modes
BLC (Back Light Compensation)
Day&Night (Auto / DAY / NIGHT / EXT)
Privacy Zone 4point
AGC (Auto Gain Control)
Sense-up (x2 ~ x32)
MIRROR (NORMAL /MIRROR/VERTICAL /ROTATE)
VIDEO OUT(BNC)
Motion Detection
Internal / AC line lock
Operates in 12 VDC or 24 VAC
Use Certified / Listed Class 2 power supply only.
Camera Mount : camera mount directily to the wall or ceiling
4-9mm Day/Night A/I Varifocal Lens F1.6~2.4
INTRODUCTION
Test Monitor Output
2
CAMERA CONNECTIONS
2
3
1
REMINDER:
Never aim the camera directly into the sun.
1. Lens : 4-9mm D&N A/I Vari-focal lens for wide area monitoring.
2. Power : 24V AC input / 12V DC input
power source from a DC 12V or AC 24V ac +/-10% 60/50Hz +/-1Hz
Use Certified/Listed Class 2 power supply transformer only.
*If using DC 12V power adaptor,
use a power supply capable of supplying 8 Watts.
3. Video : BNC connector used to connect the camera to a monitor, switcher, etc.
3
BASE INSTALLATION
1
Make mounting holes and cable hole in the place (ceiling) to which
this dome camera is installed using the Drilling guide label.
Dome window
To remove dome cover, turn the dome cover counterclockwise
until locators reach end of travel and pull off.
2
Special Screw (M4)
Plastic anchor
Drilling Guide Label
BASE INSTALLATION, continued
Fasten Mounting screws(2X) and align the dome camera
with it like above picture.
Turn the dome camera to left direction about 16 degree.
The assembly of the dome window cover and liner is in reverse
order of disassembly
Finally, lock dome window cover with locking screw(M2X4)
from the accessory kit.
4
3
- Video out check-
Video out Cab le
UP
D
OW
N
ENTE R
LE
F
T
RI
G
H
T
Tact swi tc h board
Test Monitor
4
5
CAMERA ADJUSTMENT
OSD MAIN SCREEN
+…
▶
M E NU
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION
PRIVACY
OPTION
DISPLAY
SYNC
INITIAL
EXIT
D EF AU LT
A U T O
+…
+…
+…
+…
+…
+…
- [ENTER] ON or OFF of OSD MENU
- [UP] / [DOWM] UP or DOWN of Cursor
- [LEFT] / [RIGHT] SUB MENU ON or Decision
1) EXPOSURE, WHITE BAL, DAY/NIGHT, MOTION, PRIVACY, OPTION and
DISPLAY has a SUB MENU. [UP]/[DOWN] of Cursor.
And SUB MENUS is displayed by [LEFT] / [RIGHT].
2) SYNC : AUTO or INT can be selected.
4) To EXIT the menu use the [LEFT] / [RIGHT] buttons when EXIT is highlighted.
3) When making INITIAL from USER to DEFAULT, all data is initialized.
6
▶
M E NU
EXPOSURE
WHITE BAL
DAY/NIGHT
MOTION
PRIVACY
OPTION
DISPLAY
SYNC
INITIAL
EXIT
EXPOSURE
LENS
BRIGHTNESS
BACKLIGHT
SHUTTER
AGC
SENSE UP
RETURN
▶
WHITE BAL
WB MODE
RED CONT
BLUE CONT
PUSH AUTO
RETURN
▶
MOTION
DETECT MODE
DETECT AREA
SENSITIVITY
ALARM TIME
RETURN
PRIVACY
AREA
MASK
LEVEL
TOP
DOWN
LEFT
RIGHT
RETURN
▶
▶
DAY/NIGHT
D/N MODE
AUTO LEVEL
FILTER DLY
S I N
SEN OR
RETURN
▶
OPTION
TITLE
NEGA/POSI
SHARPNESS
MIRROR
ZOOM
PAN/TILT
PHASE
RETURN
DISPLAY
TITLE
MOTION DET
RETURN
▶
▶
7
1) LENS
2) BRIGHTNESS
3) BACKLIGHT
4) SHUTTER
5) AGC
6) SENSE UP
7) RETURN
DC, ELC can be selected.
0 to 60 can be selected.
Level setting is available in DC mode.
*
ON or OFF can be selected.
Prevents such a back light effect to secure a clear image under
*
all illumination environments.
1/60 (1/50), FLC, 1/250, 1/500, 1/1000, 1/2000, 1/4000,1/10000
1/30000, 1/60000, 1/120000 sec.
When LENS is DC or VIDEO, it is possible to select it.
*
Another becomes NOT USE.
AGC OFF, LOW, MID, HIGH can be selected.
As the level of gain increases, the screen gets brighter and the level
*
Of noise also increases.
OFF, x2, x4, x8, x16, x32 can be selected.
SENSE UP helps maintain a bright, clear screen image
*
by automatically detecting change in the level of light
Return to MAIN MENU.
<EXPOSURE>
Press the [LEFT] or [RIGHT] button to access the "EXPOSURE" mode.
<WHITE BALANCE>
Press the [LEFT] or [RIGHT] button to access the "WHITE BALANCE" mode.
- ATW
- AWC
2) RED CONT
3) BLUE CONT
4) PUSH AUTO
5) RETURN
- MANUAL
This mode can be used within the color temperature range
1.800°K ~ 10.500°K
Please press the [LEFT] or [RIGHT] button in the PUSH AUTO mode
while the camera is directed at a piece of while paper to obtain the
optimum state under current illumination.
If the environment including the light source is
changed, you have to adjust the White balance again.
Adjust Red Gain Value (0 ~ 127)
Can be adjust while in manual mode.
Adjust BLUE Gain Value (0 ~ 127)
Can be adjust while in manual mode.
When it is AWC, OFF to PUSH can be selected.
Return to MAIN MENU.
Manual mode. User can change R and B Gain manually.
1) WB MODE
8
(IR camera default setting : EXT)
<DAY/NIGHT>
Press the [LEFT] or [RIGHT] button to access the "DAY/NIGHT" mode.
1) D/N MODE
- AUTO
- DAY
- NIGHT
- EXT
2) AUTO LEVEL
3) FILTER DLY
4) SENSOR IN
AUTO, DAY, NIGHT, EXT can be selected.
This camera has a function which automatically changes to
the appropriate mode for day-time or night-time.
In this mode, the camera outputs the video image only in color.
In this mode, the camera outputs the video image only in black and white.
In this mode, an external signal changes the camera output from the
COLOR mode to BW mode and back.
When set to AUTO, the 0 to 18 values can be selected.
AGC LOW : 0 ~ 3 AGC MID : 0 ~11 AGC HIGH : 0 ~18
*
When set to AUTO, 4 to 10 can be selected.
When AGC is OFF, NOT USED.
Adjust the delay time of filter movement when changing
*
from on to off or off to on.
When it is EXT, No or NC Can be selected.
<MOTION>
Press the [LEFT] or [RIGHT] button to access th "MOTION"mode.
1) DETECT MODE
2) DETECT AREA
3) SENSITIVITY
4) ALARM TIME
5) RETURN
ON or OFF can be selected.
Turning on becomes invalid while displaying OSD.
*
However, it becomes effective only at MOTION AREA.
MOTION AREA is displayed.
0 to 8 can be selected.
1 to 60 sec can be selected.
Return to MAIN MENU.
<PRIVACY>
Press the [LEFT] or [RIGHT] button to access the “PRIVACY” mode.
1) AREA
2) MASK
3) LEVEL
4) TOP
5) DOWN
6) LEFT
7) RIGHT
8) RETURN
1 to 4 can be selected.
ON or OFF can be selected.
When MASK is ON, 3 to 124(NTSC) or 6 to 150(PAL) can be selected.
When MASK is ON, 5 to 126(NTSC) or 8 to 152(PAL) can be selected.
When MASK is ON, 0 to 187(NTSC) or 0 to 185(PAL) can be selected.
When MASK is ON, 2 to 189(NTSC) or 2 to 187(PAL) can be selected.
Return to MAIN MENU.
When MASK is ON, 0 to 15 can be selected.
*It set the same value regardless of a set value of the AREA size.
<OPTION>
Press the [LEFT] or [RIGHT] button to access the "OPTION" mode.
1) TITLE
2) NEGA/POSI NEGA or POSI can be selected.
3) SHARPNESS 0 to 15 can be selected.
4) MIRROR
NORMAL, MIRROR, VERTICAL, ROTATE can be selected.
- MIRROR Horizontal image inversion
- VERTICAL Vertical image inversion
- ROTATE Horizontal image and Vertical image inversion
5) ZOOM 0FF(x1) and ON1 to ON8(x4) can be selected.
When PAN/TILT is ON, it is NOT USE.
6) PAN/TILT OFF or ON(x2) can be selected.
* When OSD MENU is OFF and PAN/TILT is ON,
o p erate by [UP],[DOWN],[LEFT],[RIGHT].
7) PHASE Sync phase is adjustable in line lock mode (Auto mode)
0 ~ 524 (NTSC) or 0 ~ 624 (PAL).
8) RETURN Return to MAIN MENU
<DISPLAY>
Press the [LEFT] or [RIGHT] button to access the "DISPLAY" mode.
TITLE
NOPQRSTUVWXYZ
ABCDEFGH I J KLM
END
POS
BS
abcdefghi j k
l
m
nopqr
s t
uvwxyz
* /
#
! % ( ) "
_
+ - ~
; .
012 3 456 78 9 :
&
A. TITLE
B. Command Line
: Move to left
: Move to right
BS : Erase a left character
POS : Change the position of the title
END : End
C. Charactor Table
: brank
: space
_
A
B
C
9
1) TITLE
2) MOTION DET
3) RETURN
ON or OFF can be selected.
ON or OFF can be selected.
Return to MAIN MENU.
LENS ADJUSTMENT (OPTIONAL VARIFOCAL LENS)
10
Field of view: Adjust setting from Tele (T)
to Wide (W) field of View.
Focus: Adjust lens focus from near
(N) to infinity ( ).
DC AUTO IRIS LENS
Image Size 1/3" CCD
Focal Length
Aperture Ratio
Angular
Field of View
4-9mm
DIAGONAL
o
4mm : 92.4
o
9mm : 39.2
4.0-9.0mm 5%
1 : 1.6 5%
Black Control ( - )
White Control ( + )
Red Drive ( + )
Green Drive ( - )
LENS
N
T
W
Adjust Focus
Adjust Angular Field View
11
SPECIFICATIONS
1/60(1/50) / FLICKERLESS / MANUAL SHUTTER
(1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000)
Power source
Power consumption
Image sensor
Total number of pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
Min. illumination
Video output
Power input
AGC
Lens mount
1/3" SONY Super-HAD CCD
2:1 interlace
15.734KHz(H) x 59.94Hz(V)
Internal / Line Lock
1/60 ~ 1/120,000 sec.
540 TV Lines
0.5 lux(Color), 0 lux (IR LED ON) @ F1.2, 50 IRE
More then 50dB (AGC off)
AUTO / DAY / NIGHT / EXT
(IR Camera default setting : EXT)
INITIAL / EXIT(Auto save) / RETURN
795(H) x 596(V)
2-Pin wire
Fixed Mount
IDI-540N
3.5 Watts / 6.0 Watts (IR ON)
811(H) x 508(V)
MODEL
S/N ratio
Auto Exposure
Lens(Auto Iris Control)
Sense-up
BLC
Privacy zone
Day & Night
White Balance
Display Title
Motion detection
Power
15.625KHz(H) x 50Hz(V)
1/50 ~ 1/120,000 sec.
Lens
Connector
&
etc.
IDI-540P
Video output
Operating Temperature
1.0 Vp-p (75 ohm, composite)
DC / ELC
ATW / AWC / MANUAL
OFF / x2 /x4 / x8 / x16 / x32
ON / OFF
OFF / ON (4 point)
POSI / NEGA
OFF / ON (Sensitivity & Alarm time Selective)
BNC connector
o o o o
-10 C ~ 50 C [14 F ~ 122 F
]
General
DNR Funcion
Function Control
TACT Switch
ON
OFF / LOW / MIDDLE / HIGH
OFF / ON
Preset
Mirror
Video Picture
NORMAL / MIRROR / VERTICAL / ROTATE
Zoom
INT / AUTO
Sync
OFF(x1) / ON1 ~ ON8(x4)
(When PAN/TILT is ON, it is NOT USE.)
Day/Night A/I Varifocal 4~9mm Lens, F1.6~2.4
(Day/Night A/I Varifocal 2.6~6mm Lens is optional)
IR LED
IR Wavelenght
IR distance range
IR project angle
IR ON/OFF
23 pcs high brightness IR LED
IR
850nm
25m~30m (from object of view reflected infrared)
40 degree
Light Sensor Control
Function
Brightness
Sharpness
0 ~ 60
0 ~ 15
Pan& Tilt
OFF / ON(x2)
(When OSD Menu is OFF & PAN/TILT is ON.)
Operating humidity
0 ~ 96% (non-condencing)
EXTERNAL DIMENSION
Dimensions
Maximum Camera and
Lens Size
Window Size
Cable Entry
Weight - Unit:
Shipping:
2.6L x 1.65W x 1.65H in.
(6.5L x 4.2W x 4.2H cm)
Unit: mm
0.1 in. (2.5mm thick),
impact-resistant P.C (LEXAN)
3.93 in. (10.0cm) diameter
Two 0.3"(0.8cm)and one 0.5"(1.3cm)
opening holes.
0.61 lb. (0.28 kg)
0.82 lb. (0.37 kg)
32.9
87.9
120
100 (Inner)
MADE IN KOREA
www.inter-m.com
5030XXXXA
Loading...