GE
VT/VR4930WDM
Security
Overview
The IFS VT/VR4930WDM video transmitter/data transceiver
and video receiver/data transceiver units utilize frequency
modulation for high video transmission quality. These
environmentally hardened units provide the simultaneous
transmission of video and full-duplex data over one single
mode optical fiber and are ideal for use in unconditioned
out-of-plant or roadside installations. Completely
transparent to and universally compatible with any NTSC,
PAL, or SECAM CCTV camera system. All standard pan-tiltzoom control signals including RS-232, RS-422, and 2-wire
RS-485 data are supported. Plug-and-play design ensures
ease of installation and no electrical or optical adjustments
are ever required. LED indicators are provided for rapidly
ascertaining equipment operating status, and these units are
available in either stand-alone or rack mount configurations.
Application Examples
• CCTV with PTZ Control
IFS FM Video
with Bi-Directional Data
Standard Features
• Frequency Modulation for High Quality Video Transmission
• Directly Compatible with All NTSC, PAL, or SECAM CCTV
Camera Systems
• LED Status Indicators Provide Rapid Indication of Critical
Operating Parameters
• Integrated WDM for Greater Reliability
• Solid-State Current Limiters on All Power Lines Provide
Equipment Protection
• Wide Optical Dynamic Range: Optical Attenuators are
Never Required
• Robust Design Ensures Extremely High Reliability In
Unconditioned Roadside Environments
• Tested and Certified by an Independent Testing Laboratory
for Full Compliance with the Environmental Requirements
(Ambient Operating Temperature, Mechanical Shock,
Vibration, Humidity with Condensation, High-Line/Low-Line
Voltage Conditions and Transient Voltage Protection) of
NEMA TS-1/TS-2 and the Caltrans Specification for Traffic
Signal Control Equipment.
FM Video with
Bi-Directional Data
Video and data units
designed for FM high quality
video transmission.
• NTCIP Compatible
• Comprehensive Lifetime Warranty
Video
(Coax)
Control
Data
Video
(Coax)
1 Fiber
9/125µm SM
VT4930WDM
Control
Data
VR4930WDM
up to 43 miles
(69 km)
ifs
International
Fiber
Systems
Incorporated
203.426.1180
ifs
International
Fiber
Systems
Incorporated
203.426.1180
GE
Security
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E sales@ifs.com
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
© 2008 General Electric Company
All Rights Reserved
Agency compliance
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
Specifications
Video
Video Input: 1 volt pk-pk (75 ohms)
Bandwidth: 5 Hz - 6.5 MHz
Differential Gain: <3%
Differential Phase: <3°
Tilt: <1%
Signal-to-Noise Ratio (SNR): 60 dB Minimum @ Maximum Optical Power Budget
Data
Data Interface: RS-232. RS-422, 2-Wire RS-485
Data Format: NRZ, NRZI, Manchester, Bi-phase
Data Rate: DC-100 Kbps (NRZ)
Operating Mode: Simplex or Full Duplex
Wavelength 1310/1550 nm, Single Mode
Optical emitter Laser Diode
Number of fibers 1
Led indicators VT: Video Input Sync Presence, Transmitted Data, Received Data,
Optical Carrier Detect, Operating Power
VR: Video Output Sync Presence, Transmitted Data, Received Data,
Optical Carrier Detect, Operating Power
Connectors
Optical: ST, SC, or FC (see ordering information)
Power and Data: Terminal Block with Screw Clamps
Video and Sync: BNC (Gold Plated Center-Pin)
Electrical & Mechanical
Power:
Surface Mount: VT: 24 VAC C.T. @ 300 mA
VR: 24 VAC C.T. @ 600 mA
Rack: From Rack
Number of Rack Slots: 2
Current Protection: Automatic Resettable Solid-State Current Limiters
Max. RG59 Cable Length: 750 ft.
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.9 x 2.0 in., 17.8 x 12.5 x 5.1 cm
Rack Mount: 7.7 x 5.0 x 2.0 in., 19.6 x 12.7 x 5.1 cm
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.
Ordering Information
Part Number Optical Pwr. Budget Max. Distance*
Single Mode
9/125µm
Accessories
◆
Options
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget.
VT4930WDM
VR4930WDM
PS-24 VAC C.T. 24 Volt AC Center Tap Power Supply (Included)
PS-24 VAC C.T.-230 24 Volt AC CenterTap Power Supply, 230 VAC Input (Included if specified at time of order)
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-SC’ to Model Number for SC Optical Connector (For Single Mode equipment only)
Add ‘-FC’ to Model Number for FC Optical Connector (For Single Mode equipment only)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
Description
Video Transmitter/Data Transceiver (1310/1550 nm)
Video Receiver/Data Transceiver (1550/1310 nm)
◆
All accessories are third party manufactured.
Fibers Required
1
System Design
23 dB
43 miles (69 km)