VT7420-2DRDT
VR7420-2DRDT
VT7420-2DRDT-R3
VT7430-2DRDT
VT7430-2DRDT-R3
VR7420-2DRDT-R3
VR7430-2DRDT
VR7430-2DRDT-R3
IFS Fiber Module
Installation & Operation
Instructions
P/N 1062784 • REV B • ISS 01JUL11
1
NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.
2
3
4
POWER
CAMERA ON
VIDEO
INPUT
VIDEO TRANSMITTER
OFF
VT7430-2DRDT
4 CHANNEL DIGITAL
+
2 CHANNEL
DATA TRANSCEIVER
ifs
232
sw
1
1
2
OFF
ON
2
International
Fiber
Systems
Incorporated
2w
422
485
ON
OFF
OFF OFF
4w
485
ON
ON
RS422/
2W RS485
RS232
RS422/
4W RS485
RS422/
2W RS485
RS232
RS422/
4W RS485
- DATA (IN/OUT)- 7
+ DATA (IN/OUT) - 6
RS232 DATA IN- 5
RS232 DATA OUT- 4
- DATA OUT- 3
+ DATA OUT- 2
- DATA (IN/OUT)- 7
+ DATA (IN/OUT) - 6
RS232 DATA IN- 5
RS232 DATA OUT- 4
- DATA OUT- 3
+ DATA OUT- 2
POWER
- 1
- 1
- 8
- 8
OPTICAL
IN/OUT
- 2
+12 VDC- 1
4 BNC Cables
(Fixed Video Inputs from Cameras)
OFF
VR7430-2DRDT
4 CHANNEL DIGITAL
VIDEO RECEIVER
+
2 CHANNEL
DATA TRANSCEIVER
ifs
232
sw
1
1
2
OFF
ON
2
International
Fiber
Systems
Incorporated
2w
422
485
ON
OFF
OFF OFF
4w
485
ON
ON
Simplex single mode
fiber optic cable
4 BNC Cables
(Video Output to Monitors)
RS422/
2W RS485
RS232
RS422/
4W RS485
RS422/
2W RS485
RS232
RS422/
4W RS485
- DATA (IN/OUT)- 7
+ DATA (IN/OUT) - 6
RS232 DATA IN- 5
RS232 DATA OUT- 4
- DATA OUT- 3
+ DATA OUT- 2
- DATA (IN/OUT)- 7
+ DATA (IN/OUT) - 6
RS232 DATA IN- 5
RS232 DATA OUT- 4
- DATA OUT- 3
+ DATA OUT- 2
POWER
- 8
- 1
- 8
OPTICAL
- 1
IN/OUT
+12 VDC- 1
- 2
Black wire
Black with
white stripe
VT/VR7430-2DRDT
RS232 DATA
RS422 DATA
2-WIRE
RS485 DATA
ON
ON
ON
OFF
OFF
ON
21
ON
OFF
21
OFF
21
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Ground
Data Input
Data Output
Ground
- Data In
+ Data In
- Data Out
+ Data Out
- Data In/Out
+ Data In/Out
4-WIRE
RS485 DATA
ON
ON
21
ON
8
7
6
5
4
3
2
1
- Data In
+ Data In
- Data Out
+ Data Out
A
VT7430-2DRDT
B
F
C
G
D
H
E
B
1 2
OFF
1 2
A
TX RX
TX RX
R
Q
CARRIER DETECT
CHAN 1 CHAN 2
CHAN 3 CHAN 4
POWER
O
P
N
CAMERA ON
I
J
K
L
M
Carrier Detect
A
Channel A Data: Switch 1
B
C
Channel A Data: Switch 2
Electrical Data Transmitted Channel A
D
Optical Data Received Channel A
E
Video Input From Camera: Channel 1
F
Camera 1 "ON"
G
Video Input From Camera: Channel 2
H
Camera 2 "ON"
I
Video Input From Camera: Channel 3
J
Camera 3 "ON"
K
Video Input From Camera: Channel 4
L
Camera 4 "ON"
M
Power
N
Electrical Data Transmitted Channel B
O
LED: RED to GREEN
LED: RED to GREEN
LED: RED to GREEN
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: RED to GREEN
Optical Data Received Channel B
P
Channel B Data: Switch 1
Q
Channel B Data: Switch 2
R
LED: RED to GREEN
VR7430-2DRDT
E
H
A
F
I
B
G
J
C
D
K
A
1 2
TX RX
CHAN 1 2
TX RX
TRANSMIT
CARRIER
REMOTE VIDEO ON
3 4
LOCAL VIDEO ON
B
1 2
OFF
POWER
RECEIVER
LOCKED
O
P
N
R
Q
M
L
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
Channel A Data: Switch 1
Channel A Data: Switch 2
Electrical Data Transmitted Channel A
Optical Data Received Channel A
Video Present at Transmitter: Channel 3
Video Present at Transmitter: Channel 2
Video Present at Transmitter: Channel 1
Video Present at Receiver: Channel 1
Video Present at Receiver: Channel 2
Video Present at Receiver: Channel 3
Video Present at Receiver: Channel 4
Video Present at Transmitter: Channel 4
Receiver Locked
Power
Electrical Data Transmitted Channel B
Optical Data Received Channel B
Channel B Data: Switch 1
Channel B Data: Switch 2
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
LED: Illuminates
INSTALLATION INSTRUCTIONS FOR ADDITIONAL COMPONENTS
REQUIREDTO MEET EMISSION REQUIREMENTS ON THE
VR74XX-2DRDT SERIES STAND ALONE UNIT.
Install Supplied EMI Filters (IFS P/N FL28A0640-0A0 or Steward P/N
28A06040-0A0 on each data cable as shown.
The data cables must have two turns through the clamp!
INSTALLATION INSTRUCTIONS FOR ADDITIONAL COMPONENTS REQUIRED
TO MEET EMISSION REQUIREMENTS ON THE VT74XX-2DRDT-R3 and
VR74XX-2DRDT-R3 Series RACK MOUNT UNITS.
INSTALL SUPPLIED CONDUCTIVE FOAM GASKET
(IFS P/N MMRFGSKT 375X500 or CHOMERICS P/N 82-122-74021-09600)
CUT TO 3 INCH LENGTH AND PLACE ON TOP RAIL OF THE RACK
(AS SHOWN), WHERE THE UNIT IS TO BE INSTALLED.
GASKET
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
CLASS 1 LASER PRODUCT
(For purposes of IEC 60825-1)
Complies with FDA Performance Standard for Laser Products
Title 21
Code of Federal Regulations
Subchapter J
Comprehensive
Lifetime Warranty
(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontinuance, warranty support is limited to ve (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for
manufactured by Seller (e.g., ber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period oered by
the original manufacturer, if any.
(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notied of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and maintenance, and conformance with
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.
(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,
any applicable recommendations of
products not
(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
eorts, the parties will negotiate an equitable adjustment in price.
(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,
liability shall terminate and BUYER shall have a reason-
all such
able time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.
Contacting us
For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).
Sales and support contact information
North
America
Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.
Outside the toll-free area: 503.885.5700.
E-mail: techsupport@interlogix.com
Europe
Australia
Select Contact Us at www.utcfssecurityproducts.eu
security.tech.support@interlogix.com.au
Note: Be ready at the equipment before calling.
Online
Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:
http://www.interlogix.com/transmission
1
1. Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.
Product Disassembly Instructions for WEEE
Per European Directive 2002/95/EC Waste Electrical and
Electronic Equipment
Required Tools:
One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.
For the enclosed box version:
1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.
2. Lift off box top cover.
3. Locate and remove securement screws for printed circuit board.
4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
5. Lift off printed circuit board.
6. Disassembly of box version of product is complete.
For rack version:
1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.
2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.
3. Lift off printed circuit board(s).
4. Disassembly of rack card version of product is complete.
Copyright © 2011 UTC Fire & Security. All rights reserved.
r
Trademarks and
patents
Manufacture
Certification
ACMA compliance Notice! Thi
Canada This Class A digital apparatus complies with Canadian ICES-003.
European Union
directives
Interlogix and IFS names and logos are trademarks of
UTC Fire & Security.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
N4131
product may cause radio interference in which case the user may be
required to take adequate measures.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0
2004/108/EC (EMC directive): Hereby, UTC Fire & Security
decl
requirements and other relevant provisions of Directive
2004/108/EC.
03 du Canada.
ares that this device is in compliance with the essential
s is a Class A product. In a domestic environment this
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information For contact information, see www.interlogix.com.
Loading...