Interlogix VR71630-2DRDT-R3 User Manual

VT71630-2DRDT-R3
VR71630-2DRDT-R3

IFS Fiber Module
Installation & Operation
Instructions

P/N 1062781 • REV B • ISS 01JUL11

VT/VR71630 -2DRDT

RS232 DATA

ON

OFF

21

ON

7
6
5
4
3
2
1

Data Input
Data Output

Ground

RS422 DATA

2-WIRE
RS485 DATA

4-WIRE
RS485 DATA

ON

ON

ON

OFF

ON

ON

OFF

21

OFF

21

21

ON

7
6
5
4
3
2
1

7
6
5
4
3
2
1

7
6
5
4
3
2
1

NOTE: A 120 ohm resistor (provided)
may need to be connected across
the data lines to ensure proper
operation.

- Data In
+ Data In

- Data Out
+ Data Out

- Data In/Out
+ Data In/Out

- Data In
+ Data In

- Data Out
+ Data Out

NOTE: A 120 ohm resistor (provided)
may need to be connected across
the data (IN) lines to ensure proper
operation.

A

NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.

B

8 CHANNEL DIGITAL VIDEO TRANSMITTER

VT7800A-2DRDT

2 CHANNEL DATA TRANSCEIVER

+

ifs

POWER

VIDEO STATUS

CHAN 1 CHAN 5

CHAN 2 CHAN 6

CHAN 3 CHAN 7

CHAN 4 CHAN 8

VT71630-2DRDT

OPTICAL
CARRIER

RX
TX

RX

TX

1
2

VT7800B

8 CHANNEL

DIGITAL VIDEO TRANSMITTER

A

OFF

ifs

1
2

B

OFF

POWER

CWDM1X5

ifs

VIDEO STATUS

CHAN 9 CHAN 13

CHAN 10 CHAN 14

CHAN 11 CHAN 15

CHAN 12 CHAN 16

VT71630-2DRDT

PS-R3

POWER SUPPLY

115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ

POWER

International
Fiber

ifs

Systems
Incorporated

ifs

C

Simplex Single

Mode Fiber

Optic Cable

8 CHANNEL DIGITAL VIDEO RECEIVER

VR7800AX-2DRDT

2 CHANNEL DATA TRANSCEIVER

+

ifs

VIDEO STATUS

VT VT

VR VR

VT VT

VR VR

VT VT

VR VR

VT VT

VR VR

VR71630-2DRDT

OPTICAL
CARRIER

POWER

CH 1 CH 5

CH 2 CH 6

CH 3 CH 7

CH 4 CH 8

A

Video input from a camera

B

Power

C

Carrier is detected from the transmitter

VR7800B

8 CHANNEL

DIGITAL VIDEO RECEIVER

A

RX
TX

B

RX

TX

1
2

OFF

OFF

1
2

ifs

CWDM1X5

OPTICAL
CARRIER

POWER

ifs

VIDEO STATUS

VT VT

CH 9 CH 13

VR VR

VT VT

CH 10 CH 14

VR VR

VT VT

CH 11 CH 15

VR VR

VT VT

CH 12 CH 16

VR VR

VR71630-2DRDT

LED changes from RED to GREEN

LED illuminates GREEN

LED changes from RED to GREEN

PS-R3

POWER SUPPLY

115VAC - 1A 50/60HZ
220VAC - 1/2A 50/60HZ

POWER

International
Fiber

ifs

Systems
Incorporated

ifs

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.

Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to cor­rect the

interference at his own expense.

CLASS 1 LASER PRODUCT

(For purposes of IEC 60825-1)

Complies with FDA Performance Standard for Laser Products

Title 21

Code of Federal Regulations

Subchapter J

Comprehensive
Lifetime Warranty

(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontin­uance, warranty support is limited to ve (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for
manufactured by Seller (e.g., ber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period oered by
the original manufacturer, if any.

(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notied of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and mainte­nance, and conformance with
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.

(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,

any applicable recommendations of

products not

(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
eorts, the parties will negotiate an equitable adjustment in price.

(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,

liability shall terminate and BUYER shall have a reason-

all such
able time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.

Contacting us

For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).

Sales and support contact information

North
America

Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.

Outside the toll-free area: 503.885.5700.

E-mail: [e-mail]

Europe

Australia

Select Contact Us at www.utcfssecurityproducts.eu

[e-mail]

Note: Be ready at the equipment before calling.

Online

Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:

http://www.interlogix.com/transmission

1

1. Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will
need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.

Product Disassembly Instructions for WEEE

Per European Directive 2002/95/EC Waste Electrical and

Electronic Equipment

Required Tools:

One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.

For the enclosed box version:

1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.

2. Lift off box top cover.

3. Locate and remove securement screws for printed circuit board.

4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.

5. Lift off printed circuit board.

6. Disassembly of box version of product is complete.

For rack version:

1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.

2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.

3. Lift off printed circuit board(s).

4. Disassembly of rack card version of product is complete.

Copyright © 2011 UTC Fire & Security. All rights reserved.

r

Trademarks and

patents

Manufacture

Certification

ACMA compliance Notice! Thi

Canada This Class A digital apparatus complies with Canadian ICES-003.

European Union

directives

Interlogix and IFS names and logos are trademarks of

UTC Fire & Security.
Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

N4131

product may cause radio interference in which case the user may be
required to take adequate measures.

Cet appareil numérique de la classe A est conforme à la norme
NMB-0

2004/108/EC (EMC directive): Hereby, UTC Fire & Security

decl
requirements and other relevant provisions of Directive
2004/108/EC.

03 du Canada.

ares that this device is in compliance with the essential

s is a Class A product. In a domestic environment this

2002/96/EC (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.

Contact information For contact information, see www.interlogix.com.